☆ 4.7 Article

Optimization in strength-ductility of Mg-RE-Zn alloy based on different repetitive upsetting extrusion deformation paths

MATERIALS & DESIGN (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Back stress dynamic balancing strategy enabled strength-ductility synergy in heterostructured Al-SiC composites

Dongxin Mao et al.

Summary: An ingenious nano-micro SiC-reinforced Al matrix composite (AMC) with heterogeneous grain structures was designed via a novel deformation-driven metallurgy method. By tailoring the accumulated geometrically necessary dislocations and intragranularly dispersed SiC particles based on the principle of back stress amelioration, a dynamic balance between strength and ductility was maintained. The designed composite exhibited a high ultimate tensile strength of 324 MPa and a uniform elongation of 12.9%, with a strength that was 181% higher than that of the ductile SiC10(mu p)/Al composite. This research provides a new strategy to promote strength-ductility synergy by modifying back stress.

SCIENCE CHINA-MATERIALS (2023)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of heat treatment on mechanical properties of an extruded Mg-4.3Gd-3.2Y-1.2Zn-0.5Zr alloy and establishment of its Hall-Petch relation

Lei Liu et al.

Summary: The effects of different treatments on the microstructure and mechanical properties of an extruded Mg-4.3Gd-3.2Y-1.2Zn-0.5Zr alloy were investigated. The study found that grain growth, texture changes, and stability of LPSO phases have an impact on the alloy's properties.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Combining gradient structure and supersaturated solid solution to achieve superior mechanical properties in WE43 magnesium alloy

Wanting Sun et al.

Summary: Surface mechanical attrition treatment was used to produce a gradient nanostructured layer on WE43 magnesium alloy, resulting in enhanced mechanical properties with exceptional strain hardening effects.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Optimization in strength-ductility of heterogeneous Mg-13Gd alloy via small extrusion ratio combined with pre-aging

Shuaishuai Liu et al.

Summary: In this study, a Mg-13Gd alloy sheet was fabricated through hot extrusion combined with aging prior to extrusion treatment, showing a combination of strength and ductility attributed to various factors such as the synergy of heterogeneous texture between coarse and fine grains, elevated heterogeneous deformation-induced strengthening and hardening, pre-existing precipitates, and dynamic generation of nanoscale chain-like precipitates during deformation. The findings provide guidance for designing magnesium-rare earth alloys with excellent strength and ductility.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Dilute long period stacking/order (LPSO)-variant phases along the composition gradient in a Mg-Ho-Cu alloy

Kai Guan et al.

Summary: The microstructures of an as-cast Mg97.49Ho1.99Cu0.43Zr0.09 alloy were investigated using atomic resolution high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM). The study revealed the presence of ordered long period stacking/order (LPSO) phases and short-range order (SRO) clusters embedded in stacking fault layers. The results support the importance of L1(2)-type TM6RE8 clusters in the formation of LPSO phases.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Plastic deformation mechanism and hardening mechanism of rolled Rare-Earth magnesium alloy thin sheet

Jia-fei Deng et al.

Summary: In this study, a rolled rare earth magnesium alloy thin sheet was successfully prepared, and the plastic deformation mechanism and hardening mechanism were explored. The shape of the precipitates and the competition between local strain and macroscopic strain were found to affect the plastic deformation behavior of the alloy.

MATERIALS & DESIGN (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Revealing the role of heterostructural parameters in hetero-deformation induced stress of Mg-13Gd alloy

Shuaishuai Liu et al.

Summary: This paper investigates the effect of heterostructural parameters on the evolution of geometrically necessary dislocations (GNDs) and heterodeformation induced (HDI) stress. The results show that the heterogeneous texture between coarse and fine grains, as well as the larger dislocation storage space in coarse grains, play important roles in affecting the density of GNDs and the level of HDI stress.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of grain size on microstructure, mechanical properties and strain hardening behavior of Mg-0.3Ca (wt.%) alloy

X. Q. Liu et al.

Summary: In this study, Mg-0.3Ca binary alloy with different grain sizes was prepared by low-temperature extrusion and heat treatment, showing a significant effect of grain size on the mechanical properties of the alloy. The alloy exhibited a decrease in tensile yield strength but an increase in elongation to failure with increasing grain size. Abnormal strain softening was observed in fine-grained samples with grain size less than 2 μm during tensile testing.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Plastic deformation and fracture mechanisms of rolled Mg-8Gd-4Y-Zn and AZ31 magnesium alloys

Jia-fei Deng et al.

Summary: This paper investigates the microstructure evolution and plastic deformation mechanism of rare-earth and rare-earth-free magnesium alloys during room temperature deformation. The results show that the twin boundaries in rare earth alloys cannot move due to the pinning effect of precipitates, leading to difficulties in slip transmission and the generation of ledges. On the other hand, slip variants between adjacent grains in rare-earth-free alloys are strain compatible, and twinning stimulates the generation of slip for coordinated deformation.

MATERIALS & DESIGN (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Heterostructured materials: superior properties from hetero-zone interaction

Yuntian Zhu et al.

Summary: Heterostructured materials are a new class of materials with superior performances that exceed the prediction by the rule-of-mixtures. By controlling heterostructures, unprecedented performances can be achieved.

MATERIALS RESEARCH LETTERS (2021)

Add to Collection

Article Chemistry, Physical

The microstructure evolution, texture weakening mechanism and mechanical properties of AZ80 Mg alloy processed by repetitive upsetting-extrusion with reduced deformation temperature

Xi Zhao et al.

Summary: The repetitive upsetting-extrusion (RUE) method is utilized to improve the strength and toughness of AZ80 Mg rods while reducing tensile anisotropy. The resulting microstructure after RUE processing shows a refinement of grains and dynamic recrystallization, leading to enhancements in mechanical properties. The introduction of an interactive stress state promotes dispersion of fiber texture and contributes to the elimination of tensile yield anisotropy in extruded bars.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced strength in pure Ti via design of alternating coarse- and fine-grain layers

Danyang Li et al.

Summary: A specially designed layered titanium with alternating coarse- and fine-grain layers (C/F-Ti) shows an extraordinarily high yield strength beyond predicted values, with the strengthening mechanism investigated through experimental characterizations. The enhanced interface constraint effect on deformation mechanism in hexagonal close-packed (hcp) materials is highlighted, demonstrating a new structural design strategy for property optimization.

ACTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructures and mechanical properties of a Mg-9Gd-3Y-0.6Zn-0.4Zr (wt.%) alloy modified by Y-rich misch metal

Nan Wang et al.

Summary: The microstructural evolution and mechanical properties of a Y-rich misch metal modified Mg-9Gd-3Y-0.6Zn-0.4Zr alloy were studied, revealing that the as-extruded and peak-aged alloys exhibit excellent yield strength at room temperature and 250 degrees C, with grain boundary strengthening and precipitation strengthening identified as the dominant mechanisms.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Nano-steps in long-period stacking ordered structures for ductility asymmetry of a strong-textured Mg-Gd-Zn alloy

Qiang Yang et al.

Summary: This study reveals strong ductility asymmetry in extruded Mg alloys containing LPSO plates, which is mainly caused by deformation steps in LPSO plates, contributing significantly to compressive ductility. The results provide fundamental insights into deformation modes and mechanisms of thin LPSO plates, as well as a better understanding of the ductility asymmetry in extruded Mg alloys containing LPSO plates.

MATERIALS & DESIGN (2021)

Add to Collection

Article Chemistry, Physical

Microstructure and texture evolution of Mg-RE-Zn alloy prepared by repetitive upsetting-extrusion under different decreasing temperature degrees

Guanshi Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

The evolution of long-period stacking ordered phase and its effect on dynamic recrystallization in Mg-Gd-Y-Zn-Zr alloy processed by repetitive upsetting-extrusion

Yingze Meng et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Achieving enhanced mechanical properties in Mg-Gd-Y-Zn-Mn alloy by altering dynamic recrystallization behavior via pre-ageing treatment

Kui Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of long-period stacking ordered phases and their effect on recrystallization in extruded Mg-Gd-Y-Zn-Zr alloy during annealing

Jianxiong Xiao et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Chemistry, Physical

Mechanical properties and Hall-Petch relationship of the extruded Mg-Zn-Y alloys with different volume fractions of icosahedral phase

T. Y. Kwak et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Development of low-alloyed and rare-earth-free magnesium alloys having ultra-high strength

Hucheng Pan et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Altered ageing behaviour of a nanostructured Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr alloy processed by high pressure torsion

W. T. Sun et al.

ACTA MATERIALIA (2018)

Add to Collection

Review Materials Science, Multidisciplinary

Hall-Petch relationship in Mg alloys: A review

Huihui Yu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Strengthening mechanisms in magnesium alloys containing ternary I, W and LPSO phases

N. Tahreen et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Deformation Behavior of Ultra-Strong and Ductile Mg-Gd-Y-Zn-Zr Alloy with Bimodal Microstructure

C. Xu et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of LPSO phases in a Mg-Zn-Y-Gd-Zr alloy during semi-continuous casting, homogenization and hot extrusion

Tao Chen et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Towards strength-ductility synergy through the design of heterogeneous nanostructures in metals

Evan Ma et al.

MATERIALS TODAY (2017)

Add to Collection

Article Multidisciplinary Sciences

Effect of LPSO and SFs on microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Chao Xu et al.

Scientific Reports (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of a nanostructured Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr supersaturated solid solution prepared by high pressure torsion

W. T. Sun et al.

MATERIALS & DESIGN (2017)

Add to Collection

Article Multidisciplinary Sciences

Ageing behavior of extruded Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr (wt.%) alloy containing LPSO phase and γ′ precipitates

C. Xu et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

The mechanism for the high dependence of the Hall-Petch slope for twinning/slip on texture in Mg alloys

Huihui Yu et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Extrusion Speed on the Microstructure and Mechanical Properties of Mg-9Gd-3Y-1.5Zn-0.8Zr alloy

Xuan Liu et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Quantitative evaluation of creep strain distribution in an extruded Mg-Zn-Gd alloy of multimodal microstructure

Yuri Jono et al.

ACTA MATERIALIA (2015)

Add to Collection

Article Materials Science, Multidisciplinary

On the Structure, Transformation and Deformation of Long-Period Stacking Ordered Phases in Mg-Y-Zn Alloys

J. F. Nie et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Prediction models for the yield strength of particle-reinforced unimodal pure magnesium (Mg) metal matrix nanocomposites (MMNCs)

Chang-Soo Kim et al.

JOURNAL OF MATERIALS SCIENCE (2013)

Add to Collection

Article Nanoscience & Nanotechnology

An Analytical Model for Predicting the Yield Strength of Particulate-Reinforced Metal Matrix Nanocomposites with Consideration of Porosity

F. A. Mirza et al.

NANOSCIENCE AND NANOTECHNOLOGY LETTERS (2012)

Add to Collection

Article Chemistry, Physical

Microstructures and mechanical properties of Mg-10Gd-6Y-2Zn-0.6Zr(wt.%) alloy

Liang Zheng et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

Add to Collection

Article Chemistry, Physical

The relationship between (Mg,Zn)3RE phase and 14H-LPSO phase in Mg-Gd-Y-Zn-Zr alloys solidified at different cooling rates

S. Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of grain size and texture on Hall-Petch relationship for a magnesium alloy

W. Yuan et al.

SCRIPTA MATERIALIA (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of long-period stacking ordered phase on mechanical properties of Mg97Zn1Y2 extruded alloy

K. Hagihara et al.

ACTA MATERIALIA (2010)

Add to Collection

Article Chemistry, Physical

Plastic deformation behavior of Mg12YZn with 18R long-period stacking ordered structure

K. Hagihara et al.

INTERMETALLICS (2010)

Add to Collection

Article Nanoscience & Nanotechnology

Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD

Marion Calcagnotto et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Dislocation structure in rapidly solidified Mg97Zn1Y2 alloy with long period stacking order phase

M Matsuda et al.

MATERIALS TRANSACTIONS (2005)

Add to Collection

Article Materials Science, Multidisciplinary

Rapidly solidified powder metallurgy Mg97Zn1Y2Alloys with excellent tensile yield strength above 600 MPa

Y Kawamura et al.

MATERIALS TRANSACTIONS (2001)

Add to Collection

Article Materials Science, Multidisciplinary

Novel hexagonal structure and ultrahigh strength of magnesium solid solution in the Mg-Zn-Y system

A Inoue et al.

JOURNAL OF MATERIALS RESEARCH (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.