☆ 4.7 Article

A damage-based uniaxial fatigue life prediction method for metallic materials

MATERIALS & DESIGN (2023)

Related references

Note: Only part of the references are listed.

Article Mechanics

A new approach for rapid fatigue limit assessment for C45 steel based on contrast damage parameters

Alessandra Pirinu et al.

Summary: This study presents a different procedure for rapid estimation of fatigue limit for C45 steel elements under two fatigue stress ratios. Three damage parameters are proposed for fatigue limit assessment of metallic materials, estimated through a contrast-based approach using raw thermal data. The obtained thermal factors are correlated to loading conditions and fatigue limit estimations are made using linear regression and signal to noise ratio data. The results show agreement with classical methods and comparable results to other research data, adding reliability to the proposed approach for fatigue limit estimation on tempered steel.

MECHANICS RESEARCH COMMUNICATIONS (2023)

Add to Collection

Article Engineering, Mechanical

Efficient experimental methods for rapid fatigue life estimation of additive manufactured elements

Chiara Colombo et al.

Summary: Three techniques for assessing the fatigue response of AMed parts were compared and proved to be effective, with infrared thermography and ultrasonic fatigue tests identifying the most critical defects.

INTERNATIONAL JOURNAL OF FATIGUE (2023)

Add to Collection

Article Engineering, Mechanical

Strain controlled fatigue behaviour of a wire plus arc additive manufactured Ti-6Al-4V

Abdul Khadar Syed et al.

Summary: This paper investigates the cyclic deformation behavior and fatigue properties of a wire + arc additive manufactured Ti-6Al-4V alloy. Compared to Ti-6Al-4V alloys produced by other additive manufacturing processes, the material used in this study has a coarser primary columnar beta grain structure and alpha microstructure. Fatigue tests were conducted on specimens with horizontal and vertical orientations. The vertical samples, where the loading axis was parallel with the primary columnar beta grains, showed slightly higher fatigue life and a higher cyclic softening rate compared to the horizontal samples. No porosity defects were found, and cracks initiated from either the alpha laths or alpha/beta interface due to cyclic slip localization.

INTERNATIONAL JOURNAL OF FATIGUE (2023)

Add to Collection

Article Engineering, Mechanical

Rapid fatigue life prediction of butt joint using energy dissipation

Wei Wei et al.

Summary: This study aims to rapidly evaluate the fatigue life of butt joints Q310NQL2-Q345NQR2 using the concept of energy dissipation within the framework of thermodynamics. A Representative Volume Element (RVE) model is introduced to characterize the energy dissipation related to two microstructural movements, i.e., anelastic and inelastic dissipated energy. The inelastic energy dissipation is used to deduce a non-linear damage evolution model, and a normalized damage model is developed based on this. S-N curves with different probabilities are estimated using the maximum likelihood method, and they are validated by test data.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2023)

Add to Collection

Review Engineering, Mechanical

A review of fatigue damage detection and measurement techniques

Fredrik Bjorheim et al.

Summary: This paper reviews the existing techniques for fatigue damage detection and measurement, focusing on fatigue crack monitoring and fatigue damage monitoring. Parameters of these techniques are critically evaluated for choosing the suitable method for detecting fatigue crack or damage in materials or components.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Mechanics

Fatigue limit evaluation via infrared thermography for a high strength steel with two strength levels

Aiguo Zhao et al.

Summary: The study showed that in the evaluation of fatigue limit of high strength steel, the presence of grain boundaries can affect the strength performance.

ENGINEERING FRACTURE MECHANICS (2022)

Add to Collection

Article Engineering, Mechanical

Fatigue resistance evaluation of high Mn-TWIP steel through damage mechanics: A new method based on stiffness evolution

Sergi Parareda et al.

Summary: The work presents a new methodology for determining fatigue strength quickly and reliably by monitoring specimen stiffness changes. The proposed method offers a more efficient and evident experimental procedure compared to traditional methods.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

On the correlation of temperature harmonic content with energy dissipation in C45 steel samples under fatigue loading

Riccardo Cappello et al.

Summary: This study evaluates the correlation between the harmonic content of temperature and material dissipation, proposing the Second Harmonic phase parameter as an effective indicator for monitoring internal intrinsic dissipation in the material.

MECHANICS OF MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Characterization of the Fatigue Behaviour of Low Carbon Steels by Means of Temperature and Micromagnetic Measurements

Haoran Wu et al.

Summary: Investigations were conducted on low carbon steels using load increase tests and constant amplitude tests to study the correlation between material behavior, mechanical load, and the type of non-destructive testing method. Results showed differences in temperature and magnetic Barkhausen noise-derived variables during the tests.

METALS (2022)

Add to Collection

Article Engineering, Mechanical

Rapid estimation of fatigue limit for C45 steel by thermography and digital image correlation

Chiara Colombo et al.

Summary: This paper experimentally captures fatigue damage phenomenon in steels through the combination of thermography and Digital Image Correlation (DIC) measurements, providing a rapid estimation of the fatigue limit. Results indicate that both thermography and DIC-based parameters exhibit bilinear trends as a function of stress amplitude, with changes in thermal and mechanical behaviors sensitive to the selected stress ratio, giving a precise estimation of the fatigue limit.

JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN (2021)

Add to Collection

Article Engineering, Mechanical

Fatigue resistance of press hardened 22MnB5 steels

Sergi Parareda et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Engineering, Mechanical

A unified fatigue life calculation based on intrinsic thermal dissipation and microplasticity evolution

Zhenjie Teng et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Considerations about the existence or non-existence of the fatigue limit: implications on practical design

A. Fernandez-Canteli et al.

INTERNATIONAL JOURNAL OF FRACTURE (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Additive manufacturing of Ti6Al4V alloy: A review

Shunyu Liu et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Engineering, Mechanical

SteBLife - A new short-time procedure for the evaluation of fatigue data

Haoran Wu et al.

INTERNATIONAL JOURNAL OF FATIGUE (2019)

Add to Collection

Proceedings Paper Construction & Building Technology

Comparison between thermal energy and acoustic emission for the fatigue behavior of steels

F. Giudice et al.

25TH INTERNATIONAL CONFERENCE ON FRACTURE AND STRUCTURAL INTEGRITY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

The effects of bimodal grain size distributions on the work hardening behavior of a TRansformation-TWinning induced plasticity steel

H. Eskandari Sabzi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

An influence of cyclic loading on the form of constitutive relationship for DP500 steel

W. Mocko et al.

MATERIALS & DESIGN (2016)

Add to Collection

Proceedings Paper Engineering, Mechanical

Effects of microstructure and surface roughness on the fatigue strength of high-strength steels

Junbiao Lai et al.

21ST EUROPEAN CONFERENCE ON FRACTURE, (ECF21) (2016)

Add to Collection

Article Engineering, Mechanical

Fatigue crack growth of a metastable austenitic stainless steel

D. F. Martelo et al.

INTERNATIONAL JOURNAL OF FATIGUE (2015)

Add to Collection

Article Engineering, Mechanical

Crack closure and fatigue crack growth near threshold of a metastable austenitic stainless steel

D. F. Martelo et al.

INTERNATIONAL JOURNAL OF FATIGUE (2015)

Add to Collection

Article Engineering, Mechanical

Fatigue limit evaluation of various martensitic stainless steels with new robust thermographic data analysis

R. De Finis et al.

INTERNATIONAL JOURNAL OF FATIGUE (2015)

Add to Collection

Article Engineering, Mechanical

An energy method for rapid evaluation of high-cycle fatigue parameters based on intrinsic dissipation

Qiang Guo et al.

INTERNATIONAL JOURNAL OF FATIGUE (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Plastic deformation and damage induced by fatigue in TWIP steels

J. J. Roa et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Proceedings Paper Engineering, Mechanical

Fatigue tests for automotive design: optimization of the test protocol and improvement of the fatigue strength parameters estimation

Matteo Luca Facchinetti

FATIGUE DESIGN 2015, INTERNATIONAL CONFERENCE PROCEEDINGS, 6TH EDITION (2015)

Add to Collection

Article Engineering, Mechanical

Determination of high cycle fatigue properties of a wide range of steel sheet grades from self-heating measurements

Remi Munier et al.

INTERNATIONAL JOURNAL OF FATIGUE (2014)

Add to Collection

Article Engineering, Multidisciplinary

The systematic error in digital image correlation induced by self-heating of a digital camera

Shaopeng Ma et al.

MEASUREMENT SCIENCE AND TECHNOLOGY (2012)

Add to Collection

Article Engineering, Mechanical

Analysis of the fatigue strength of a stainless steel based on the energy dissipation

G. Meneghetti

INTERNATIONAL JOURNAL OF FATIGUE (2007)

Add to Collection

Article Engineering, Mechanical

A new iteration method for the thermographic determination of fatigue limit in steels

F Curà et al.

INTERNATIONAL JOURNAL OF FATIGUE (2005)

Add to Collection

Article Engineering, Mechanical

Prediction of the fatigue life on the basis of damage progress rate curves

G Socha

INTERNATIONAL JOURNAL OF FATIGUE (2004)

Add to Collection

Article Engineering, Mechanical

Experimental investigations of fatigue cracks nucleation, growth and coalescence in structural steel

G Socha

INTERNATIONAL JOURNAL OF FATIGUE (2003)

Add to Collection

Article Engineering, Mechanical

On 'multi-stage' fatigue life diagrams and the relevant life-controlling mechanisms in ultrahigh-cycle fatigue

H Mughrabi

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2002)

Add to Collection

Article Engineering, Mechanical

Rapid determination of the fatigue curve by the thermographic method

G Fargione et al.

INTERNATIONAL JOURNAL OF FATIGUE (2002)

Add to Collection

Article Engineering, Mechanical

Thermographic methodology for rapid determination of the fatigue limit of materials and mechanical components

G La Rosa et al.

INTERNATIONAL JOURNAL OF FATIGUE (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.