Related references
Note: Only part of the references are listed.
Article
Thermodynamics
Min Chang et al.
Summary: This paper proposes and comprehensively compares air-and water-cooling methods for electric motors in unmanned aerial vehicles. The effects of fan speed, water flow speed, and convection heat transfer coefficient on the cooling capacity of the electric motor are discussed. A comprehensive performance evaluation factor for the cooling method of the motor is proposed. The findings can provide guidance for designing highly efficient electric motor cooling equipment for unmanned aerial vehicles.
APPLIED THERMAL ENGINEERING
(2023)
Article
Thermodynamics
Zheng Wang et al.
Summary: This paper investigates a novel direct cooling structure for permanent magnet synchronous linear motors, which can greatly reduce the temperature rise and improve the cooling performance. Detailed numerical calculations and analysis reveal the advantages of the direct cooling structure compared with the traditional cooling structure. An improved thermal network model is proposed to accurately calculate the average winding temperature and predict the maximum temperature without additional computational burden. Experiments on a prototype verify the excellent cooling performance and effectiveness of the proposed cooling structure and improved thermal network model.
APPLIED THERMAL ENGINEERING
(2023)
Article
Thermodynamics
Myeong Hyeon Park et al.
Summary: In this study, an asymmetric lumped parameter thermal network (LPTN) model of a rotational oil-spray-cooling motor is developed. The heat loss is calculated using correlation equations and electro-magnetic analysis, and the internal temperature distribution of the motor is predicted using conjugate heat transfer and multiphase flow computational fluid dynamics (CFD) analysis. The temperature of the coil inside the motor is measured using experiments. The developed LPTN model determined that the temperature prediction errors of coil parts were 0.15% and 4.42% at the nominal and maximum speeds, respectively.
APPLIED THERMAL ENGINEERING
(2023)
Article
Thermodynamics
Wei Zuo et al.
Summary: A hydrogen-fueled micro planar combustor with tube outlet is designed to improve the energy output power and energy conversion efficiency for micro-thermophotovoltaic system. The effects of tube outlet structure parameters on the performance of micro planar combustor are numerically investigated. The results show that increasing the tube distance slightly improves the energy output and conversion efficiency, and reduces the pressure loss. Additionally, using square tubes instead of circular tubes is more suitable for the MTPV system, and increasing the number of tubes significantly enhances the energy output and conversion efficiency while reducing pressure loss.
Article
Thermodynamics
Wei Zuo et al.
Summary: Optimizing the structure of micro combustors to enhance their thermal performance can effectively improve the output power and energy conversion efficiency of micro thermophotovoltaic systems. The introduction of a tube outlet can effectively increase the mean outer wall temperature and temperature uniformity of micro planar combustors, as well as the energy output and energy conversion efficiency of MTPV system, but it also leads to higher pressure loss. The energy output and energy conversion efficiency of MTPV system can be further increased by reducing the tube length and increasing the tube diameter, while the pressure loss decreases slowly. When nickel is used as the solid wall material, the energy output and energy conversion efficiency of MTPV system can reach 6.14 W and 3.54%, respectively.
Article
Thermodynamics
Wei Zuo et al.
Summary: A hydrogen-fueled micro planar combustor with cavity is designed to achieve high energy output power and energy conversion efficiency for micro-thermophotovoltaic system. Numerical investigations show that the micro planar combustor with cavity can achieve higher and more uniform outer wall temperature. With the reduction of cavity length and outlet size, the energy output and energy conversion efficiency of MTPV increase, but the pressure loss also becomes larger. The optimal dimensionless cavity length and outlet size are found to be 3/9 and 5/7 x 1/3, respectively. Nickel is identified as the optimal solid wall material for higher energy conversion efficiency, reaching 3.86% at an inlet velocity of 5 m/s. Therefore, the micro planar combustor with cavity is more suitable for MTPV system with higher energy output and energy conversion efficiency.
Article
Thermodynamics
Zhijie Chen et al.
Summary: This study optimized the performance of a proton exchange membrane fuel cell by using response surface methodology and non-dominated ranking genetic algorithm. The Pareto optimal solution obtained through this method improves the power density, system efficiency, and exergy efficiency of the fuel cell. This work provides a new multi-objective optimization method for designing more efficient fuel cells.
ENERGY CONVERSION AND MANAGEMENT
(2023)
Article
Thermodynamics
X. Wang et al.
Summary: The development of electric cars requires powerful electric motors, and effective thermal management is essential for the efficiency, durability, and safety of motors. This paper summarizes the latest thermal management methods, including air cooling and liquid cooling, and highlights heat transfer enhancement methods based on conduction.
APPLIED THERMAL ENGINEERING
(2022)
Article
Thermodynamics
Seounghwan Hyeon et al.
Summary: A cooling system with a flow guide is proposed to enhance the winding cooling of an air-cooled motor. Thermal and flow modeling was performed using computational analysis and the results are validated through experiments. The effects of the flow guide installation on the flow and heat transfer characteristics inside the motor are analyzed, and the variation in cooling effect and pressure drop ratio with various design factors are investigated through numerical analysis.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2022)
Article
Thermodynamics
Yuntian Zhang et al.
Summary: In this study, an inclined channel cold plate was designed for a LiFePO4 battery in an electric vehicle, and its performance was compared with that of a straight channel cold plate under different conditions. The results showed that the inclined channel cold plate outperformed the straight channel cold plate, and the performance improved with a larger inclined angle. This study suggests that the inclined channel cold plate is more suitable for battery thermal management systems.
Article
Green & Sustainable Science & Technology
Wei Zuo et al.
Summary: A double S-channel cold plate is designed for cooling a battery, which can reduce temperature difference and pressure drop, and improve overall thermal performance evaluation compared to a single S-channel cold plate.
Article
Thermodynamics
Changbo Guo et al.
Summary: The study indicates that moving cooling channels into deepened stator slots can significantly lower the motor temperature with little influence on motor efficiency.
CASE STUDIES IN THERMAL ENGINEERING
(2022)
Article
Thermodynamics
Xuehui Wang et al.
Summary: This paper presents an innovative experimental study on oil spray for end winding thermal management in electric motors. The results indicate that oil spray cooling can significantly decrease the temperature of the winding, and a heat transfer performance prediction model based on an artificial neural network is developed to accurately predict the heat transfer performance of oil spray.
CASE STUDIES IN THERMAL ENGINEERING
(2022)
Article
Savithry K. Thangaraju et al.
International Journal of Thermofluids
(2022)
Article
Thermodynamics
Joonbum Park et al.
Summary: This study adopts direct slot cooling (DSC) technology to cool the traction motor of an electric vehicle. By comparing it with other existing cooling technologies, the study finds that DSC has good cooling performance, effectively controlling the temperature of the winding, and improving the dynamic performance of the motor.
APPLIED THERMAL ENGINEERING
(2022)
Article
Thermodynamics
Nianyong Zhou et al.
Summary: This paper experimentally studied the heat transfer performance of ethylene glycol spray cooling, and found that the ethylene glycol mass fraction significantly affects the heat transfer performance. The increase of dynamic viscosity and the decrease of specific heat capacity and thermal conductivity are the direct causes of this effect. Meanwhile, an increase in nozzle inlet temperature improves the surface heat transfer coefficient and increases evaporation intensity.
APPLIED THERMAL ENGINEERING
(2022)
Article
Energy & Fuels
Xiaokun Zhao et al.
Summary: This paper proposes a flux-intensifying permanent magnet synchronous motor (FIPMSM) and its magnetic equivalent circuit (MEC) model. The dynamic MEC model is established and an equivalent reluctance calculation method is used for complex structures. The accuracy of the MEC model is verified through finite element analysis and experiments.
Article
Engineering, Environmental
Tao Cai et al.
Summary: The study investigates the effect of implementing a perforated plate on NOx emissions in ammonia-fueled micro-power systems, finding that an optimized perforated plate can significantly reduce NO emissions due to the formation of a low flame temperature recirculation zone. Additionally, increasing hole width helps minimize NO generation, while hole position variation leads to an opposite trend in NOx emissions.
JOURNAL OF HAZARDOUS MATERIALS
(2021)
Article
Thermodynamics
Huaqiang Chu et al.
Summary: The study investigates the effects of oxygen-free and oxygen-containing aliphatic and aromatic hydrocarbons on soot formation, finding that soot formed in flames doped with ethanol has a unique structure, while other doped flames are susceptible to oxidation by free radicals.
COMBUSTION AND FLAME
(2021)
Article
Engineering, Electrical & Electronic
Pratik Roy et al.
Summary: The paper introduces a new cooling jacket design algorithm for permanent magnet traction motors, combining electromagnetic and thermal co-analysis, shape and size optimization, and multiphysics finite element analysis. This algorithm can achieve the performance and temperature design goals of the motor in different operating conditions.
IEEE TRANSACTIONS ON MAGNETICS
(2021)
Article
Automation & Control Systems
Alessandro Acquaviva et al.
Summary: This article presents a solution for in-slot and in-stator direct oil cooling for a tooth coil winding machine, and designs, manufactures, and verifies a corresponding 50-kW machine. Heat transfer simulations and finite-element analysis are used in the design process to establish a continuous operating point at 25 A/mm(2).
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS
(2021)
Article
Thermodynamics
Yongsheng Li et al.
Summary: A cooling system utilizing internal oil circulation and external water circulation was proposed for heat dissipation of PMSM, with an optimization framework developed to find the best parameters. Through various methods, the motor heat dissipation was effectively improved, demonstrating the practical significance of the optimization framework.
CASE STUDIES IN THERMAL ENGINEERING
(2021)
Article
Green & Sustainable Science & Technology
Ningqiang Shi et al.
Summary: A heat dissipation system was designed in this paper to address the issue of excessive temperature rise during the operation of a 2.5 MW permanent magnet wind turbine. By optimizing the cooling pipe gap and piping arrangement, it was verified that the designed cooling system meets the cooling requirements.
Article
Energy & Fuels
Feng Han et al.
Summary: The study focused on the integrated design of liquid-cooled heat sink for a 30 kW motor inverter, selecting a serpentine channel configuration for its best cooling performance. Further optimization of the heat sink's geometrical configuration led to achieving high power density of 9.677 kW/kg. Experiment results validated the numerical simulation results, showcasing the effectiveness of the design approach.
Article
Thermodynamics
Xingping Li et al.
Summary: The study investigates a highly efficient two-phase direct immersion cooling system and compares the thermal performances of three different dielectric liquids. Ethanol is found to be the optimal choice for heat dissipation under both forced air convection and natural convection.
THERMAL SCIENCE AND ENGINEERING PROGRESS
(2021)
Article
Automation & Control Systems
Chiranjit Sain et al.
Article
Thermodynamics
Yalong Sun et al.
APPLIED THERMAL ENGINEERING
(2020)
Article
Thermodynamics
Wei Chen et al.
APPLIED THERMAL ENGINEERING
(2019)
Article
Engineering, Multidisciplinary
Jian Li et al.
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS
(2019)
Article
Thermodynamics
Huaqiang Chu et al.
Article
Engineering, Multidisciplinary
Pey-Shey Wu et al.
Article
Thermodynamics
Yu Xiwei et al.
APPLIED THERMAL ENGINEERING
(2018)
Article
Energy & Fuels
Zabdur Rehman et al.
Article
Engineering, Multidisciplinary
Aurelie Fasquelle et al.
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS
(2017)
Article
Thermodynamics
Marco Satrustegui et al.
APPLIED THERMAL ENGINEERING
(2017)
Article
Thermodynamics
Kea-Ho Lee et al.
APPLIED THERMAL ENGINEERING
(2016)
Article
Thermodynamics
Dan Zhao et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
(2015)
Article
Thermodynamics
Dan Zhao et al.
Article
Thermodynamics
Junwei Li et al.
EXPERIMENTAL THERMAL AND FLUID SCIENCE
(2014)
