☆ 4.7 Article

Rapid fabrication of Si3N4 ceramics with gradient appearance and microstructure

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

The lamellar preparation of continuous porosity-graded Si3N4 ceramics without obvious interfaces for broadband radome application

Haoqian Zhang et al.

Summary: In this study, porous Si3N4 ceramics with a continuous porosity gradient were successfully achieved through lamellar gel-casting, freeze-drying, and subsequent sintering process. The porosity-graded structure exhibited excellent thermal expansion matching performance at high temperatures, making it a potential candidate for radar dome design.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

Joining dense Si3N4 to porous Si3N4 using a novel glass-ceramic interlayer with precipitated β-LiAlSi2O6/Mg2SiO4

Liangbo Sun et al.

Summary: In this work, a new beta-LiAlSi2O6/Mg2SiO4 glass-ceramic interlayer was developed to join dense and porous Si3N4 ceramics, forming a gradient infiltration layer to enhance mechanical strength and high-temperature resistance of the joint.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Comparison of the bio-tribological properties of UHMWPE-Chirulen® and PEEK-OPTIMA® articulating against ceramics: Implications for orthopedic implants

Shuai Yan et al.

Summary: The study found that under DPPC lubrication, PEEK exhibited better wear resistance than UHMWPE, and under high load and low frequency conditions, the friction coefficient of Si3N4/Chirulen(R) 1020 XPE was low. Additionally, the tribological performance of Si3N4 was superior to Al2O3 due to the formation of a protective SiO2 film on its surface in water.

MATERIALS LETTERS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

In situ fabrication of continuously graded Si3N4 ceramics via DC field-assisted hot pressing

Jingkun Xu et al.

Summary: The effects of different DC electric fields (0-167 V/cm) on the liquid-phase hot pressing of Si3N4 ceramics were investigated in this study. It was found that the application of a DC field could promote the phase transformation of Si3N4 near the cathode while inhibiting it near the anode. Additionally, the migration of Mg2+ and Y3+ ions driven by the DC field was observed, but the graded phase transformation phenomenon was linked to the Peltier effect.

SCRIPTA MATERIALIA (2022)

Add to Collection

Article Materials Science, Ceramics

Surface modification of Si3N4 powder for hydrolysis control

Songmo Du et al.

Summary: The hydrolysis of Si3N4 powder was controlled by surface modification with Al(H2PO4)(3) and Mg(H2PO4)(2) with TEOS. The existence of Al(H2PO4)(3) and Mg(H2PO4)(2) catalyzed the hydrolysis of TEOS. The surface modification had no clear influence on the dielectric loss of Si3N4 powders. The surface modification agent forms a strong bonding with the surface of Si3N4 particles.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Preparation of porous SiC ceramics skeleton with low-cost and controllable gradient based on liquid crystal display 3D printing

Huan Wang et al.

Summary: In this study, a gradient porous ceramic skeleton (GPCS) was prepared by combining a liquid crystal display (LCD) 3D printer with liquid silicon infiltration (LSI) technology. The experimental results showed that the optimal ceramic slurry for printing had ceramic powder accounting for 45% of the mass of photosensitive resin, and the photosensitive resin had a faster thermal decomposition rate in the range of 300-450 degrees C. The effects of LSI temperature on the composition, microstructure, and mechanical properties of the GPCS were also investigated.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Multidisciplinary Sciences

Plastic deformation in silicon nitride ceramics via bond switching at coherent interfaces

Jie Zhang et al.

SCIENCE (2022)

Add to Collection

Article Dentistry, Oral Surgery & Medicine

Silicon nitride ceramic for all-ceramic dental restorations

Mahmut Sertac Ozdogan et al.

DENTAL MATERIALS JOURNAL (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Silicon Nitride: A Bioceramic with a Gift

Giuseppe Pezzotti

ACS APPLIED MATERIALS & INTERFACES (2019)

Add to Collection

Article Materials Science, Ceramics

Silicon nitride bioceramics in healthcare

Mohamed Rahaman et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Ceramics

Fabrication and wear behaviors of graded Si3N4 ceramics by the combination of two-step sintering and beta-Si3N4 seeds

Jun-Jie Yu et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

Add to Collection

Article Chemistry, Multidisciplinary

A spontaneous solid-state NO donor to fight antibiotic resistant bacteria

Giuseppe Pezzotti

MATERIALS TODAY CHEMISTRY (2018)

Add to Collection

Article Multidisciplinary Sciences

Bioactive silicon nitride: A new therapeutic material for osteoarthropathy

Giuseppe Pezzotti et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Chemistry, Multidisciplinary

Silicon Nitride Bioceramics Induce Chemically Driven Lysis in Porphyromonas gingivalis

Giuseppe Pezzotti et al.

LANGMUIR (2016)

Add to Collection

Article Materials Science, Ceramics

Fabrication and properties of porous Si3N4-SiO2 ceramics with dense surface and gradient pore distribution

Xiangming Li et al.

CERAMICS INTERNATIONAL (2014)

Add to Collection

Article Orthopedics

Total knee arthroplasty in patients with hypersensitivity to metals

Massimo Innocenti et al.

INTERNATIONAL ORTHOPAEDICS (2014)

Add to Collection

Review Materials Science, Multidisciplinary

Biomimetic porous scaffolds for bone tissue engineering

Shuilin Wu et al.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2014)

Add to Collection

Article Dentistry, Oral Surgery & Medicine

Five-year results of a randomized controlled clinical trial comparing zirconia and titanium abutments supporting single-implant crowns in canine and posterior regions

Anja Zembic et al.

CLINICAL ORAL IMPLANTS RESEARCH (2013)

Add to Collection

Article Engineering, Biomedical

Anti-infective and osteointegration properties of silicon nitride, poly(ether ether ketone), and titanium implants

T. J. Webster et al.

ACTA BIOMATERIALIA (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of chemical vapor infiltration of Si3N4 on the mechanical and dielectric properties of porous Si3N4 ceramic fabricated by a technique combining 3-D printing and pressureless sintering

Xiangming Li et al.

SCRIPTA MATERIALIA (2012)

Add to Collection

Review Microbiology

Scenery of Staphylococcus implant infections in orthopedics

Lucio Montanaro et al.

FUTURE MICROBIOLOGY (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Continuous in situ functionally graded silicon nitride materials

Manuel Belmonte et al.

ACTA MATERIALIA (2009)

Add to Collection

Article Multidisciplinary Sciences

Inspiration and application in the evolution of biomaterials

Nathaniel Huebsch et al.

NATURE (2009)

Add to Collection

Article Dentistry, Oral Surgery & Medicine

Titanium allergy in dental implant patients: a clinical study on 1500 consecutive patients

Alberto Sicilia et al.

CLINICAL ORAL IMPLANTS RESEARCH (2008)

Add to Collection

© Peeref 2019-2024. All rights reserved.