☆ 4.7 Review

A review of recent developments in the corrosion performance of aluminium matrix composites

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Related references

Note: Only part of the references are listed.

Article Metallurgy & Metallurgical Engineering

Effect of B4C and CNTs' nanoparticle reinforcement on the mechanical and corrosion properties in rolled Al 5083 friction stir welds

Jehanzaib Anwar et al.

Summary: The effect of adding boron carbide and carbon nanotubes on the mechanical properties, microstructure evolution, and corrosion behavior of friction stir welded aluminium alloy 5083 plates was investigated. Tensile testing showed a decrease in strength after welding, but it increased with the addition of reinforcements. The presence of hybrid reinforcement led to premature failure due to lack of fusion and improper bonding.

CANADIAN METALLURGICAL QUARTERLY (2023)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructural, mechanical and corrosion behaviour of B4C/BN-reinforced Al7075 matrix hybrid composites

N. Ramadoss et al.

Summary: This study focuses on improving the mechanical and corrosion properties of aluminium hybrid metal matrix composites (AHMMCs) by using boron carbide (B4C) and boron nitride (BN) as reinforcement particles. The AHMMCs with different weight percentages of B4C and fixed weight percentage of BN were synthesized using the stirring-squeeze cast method. The results show that the microstructure and chemical composition changes significantly improve the performance of the composites, making them potentially useful in automotive and marine applications.

INTERNATIONAL JOURNAL OF METALCASTING (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Surface degradation behavior of aluminium cenosphere composite foam developed by powder metallurgy route

Amarish Kumar Shukla et al.

Summary: This study focuses on the effect of cenosphere content (5 vol% to 50 vol%.) on the surface degradation behavior (by wear and corrosion) of aluminum cenosphere composite foam. The composite foam was developed through compaction and two-step sintering. The density and wear resistance of the foam increased with the increase in cenosphere content up to 30 vol%, while the corrosion rate increased up to 30 vol% and then decreased.

MATERIALS CHEMISTRY AND PHYSICS (2023)

Add to Collection

Article Chemistry, Multidisciplinary

Effect of Nanoscale W Coating on Corrosion Behavior of Diamond/Aluminum Composites

Ping Zhu et al.

Nanomaterials (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on corrosion behaviors and mechanical properties of TiB2/7075Al composites with various particle contents

Liang Chen et al.

Summary: TiB2/7075Al composites with different particle contents were prepared through hot-pressing sintering and hot extrusion, and their mechanical properties and corrosion resistance were studied. The results showed that increasing TiB2 content refined the grain size, reduced texture strength, and improved wear resistance. TiB2 particles hindered corrosion channels and crack propagation, enhancing the resistance to intergranular and exfoliation corrosion, but aggravated pitting corrosion due to the destruction of the oxide film on the composite surface. The electrochemical corrosion resistance of the composite was lower than that of 7075Al without particles, but could be improved again by increasing TiB2 content.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Add to Collection

Article Materials Science, Ceramics

Effect of the B4C content on microstructure, microhardness, corrosion, and neutron shielding properties of Al-B4C composites

Yasin Gaylan et al.

Summary: The study aimed to produce and investigate the properties of Al-B4C metal matrix composites (MMCs) as an alternative material for baskets in spent fuel casks. Al-xB4C composite powders were prepared by high-energy planetary ball milling and then compacted and sintered. The microstructure analysis showed that the synthesized Al-B4C MMCs consist of Al and B4C phases with a homogeneous distribution of B4C reinforcement. The relative density, microhardness, corrosion rate, and neutron cross-section all increased with an increasing B4C ratio.

CERAMICS INTERNATIONAL (2023)

Add to Collection

Article Chemistry, Physical

Improving the properties of an Al matrix composite fabricated by laser powder bed fusion using graphene-TiO2 nanohybrid

Siavash Imanian Ghazanlou et al.

Summary: The impact of graphene-TiO2 nanohybrid reinforcement on an aluminum matrix after the laser powder bed fusion process was studied. Several characterization techniques were used to compare the microstructure, mechanical properties, wear resistance, and corrosion behavior of different nanocomposite structures. The results showed that the graphene-TiO2 nanohybrid improved the properties of the Al matrix composite by preventing the formation of Al4C3, creating strong interfacial bonding, and reducing crack propagation.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Wear and corrosion properties of low-cost eggshell-reinforced green AZ91 matrix composites

Muhammet Emre Turan et al.

Summary: This study focuses on the production of economical, recyclable, and low-weight magnesium matrix composites with waste eggshell reinforcement. The eggshell reinforcement improved the microhardness value and wear performance of the alloys, but also accelerated the corrosion rate as the reinforcement content increased. The statistical analysis showed that the wear rate was mainly affected by load, while the corrosion rate was mainly affected by pH value.

CANADIAN METALLURGICAL QUARTERLY (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of TiB2 Particles on the Morphological, Mechanical and Corrosion Behaviour of Al7075 Metal Matrix Composite Produced Using Stir Casting Process

M. Manoj et al.

Summary: This study focused on investigating the morphological, mechanical, and corrosion behavior of Al7075-TiB2 metal matrix composites. The addition of TiB2 particles through stir casting process improved the tensile strength and micro hardness of the composites, while reducing the wear rate. Electrochemical potentiodynamic polarization and salt spray tests confirmed the enhanced corrosion resistance of the Al-TiB2 composites.

INTERNATIONAL JOURNAL OF METALCASTING (2022)

Add to Collection

Article Chemistry, Physical

Structural and corrosion behavior investigation of novel nano-quasicrystalline Al-Cr-Fe reinforced Al-matrix composites produced by ARB process

Shima Pashangeh et al.

Summary: In this study, AlQC nanoparticles reinforced AMCs were produced using the ARB process, with structural evaluation conducted using XRD and SEM. The results demonstrated improvements in nanoparticle distribution and interlayer connections with increasing ARB cycles, while density measurements revealed discrepancies between theoretical and measured densities. Corrosion behavior studies showed the impact of AlQC nanoparticles on corrosion potential and rate.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Chemistry, Physical

On the interactions between molten aluminum and high entropy alloy particles during aluminum matrix composite processing

Xuejun Huang et al.

Summary: The study found that adding AlCrTiV HEA particles to molten aluminum can significantly improve the mechanical properties of metal matrix composites, primarily through grain refinement and dispersion strengthening. The interactions between matrix aluminum alloys and the particles are crucial in controlling the final microstructure and properties of the composites.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Magnetic-Mechanical Coupled Stirring on the Distribution of B4C Particles in Al-B4C Composites

Junfeng Zhao et al.

Summary: This study improved the manufacturing process of Al-B4C composites by introducing magnetic-mechanical coupled stirring, which effectively distributed B4C particles in the matrix and enhanced the composite material's properties. Through numerical investigations and experiments, an optimal configuration was selected for successful production of the composites.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Chemistry, Physical

Corrosion and Mechanical Properties of Novel AA2024 Matrix Hybrid Nanocomposites Reinforced with B4C and SiC Particles

Abdullah Hasan Karabacak et al.

Summary: The powder metallurgy method was used to synthesize a nano-sized B4C and SiC reinforced AA2024 matrix hybrid nanocomposite. The study examined the effect of B4C and SiC reinforcement content on the mechanical and corrosion behavior of the hybrid nanocomposite. The results showed that the appropriate reinforcement content could decrease the corrosion rate and increase the hardness of the hybrid nanocomposite.

SILICON (2022)

Add to Collection

Article Chemistry, Physical

Mechanical Behavior and Metallographic Characterization of Microwave Sintered Al/SiC Composite Materials - an Experimental Approach

Shoba Chintada et al.

Summary: Incorporating tougher ceramic particles into a softer aluminium matrix was traditionally considered a challenge, but powder metallurgy has emerged as a significant fabrication technology in this field. By reinforcing aluminium with silicon carbide (SiC), improvements were seen in hardness, ultimate tensile strength (UTS), and yield strength (YS), although elongation decreased rapidly. Furthermore, mechanical properties were found to increase with a decrease in reinforcement particle size.

SILICON (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Development of Al-SiC composite material from rice husk and its parametric assessment

Madhusudan Baghel et al.

Summary: In this research, Al-SiC composite material was developed from rice husk using a CNC milling machine. The material's surface was characterized and its mechanical properties were studied. The results showed that the composite material has a large surface area and good fracture toughness, making it suitable for aerospace applications.

MATERIALS RESEARCH EXPRESS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical corrosion and tribological behaviour of AA6063/Si3N4/Cu(NO3)2 composite processed using single-pass ECAPA route with 120° die angle

P. Sureshkumar et al.

Summary: The study focused on the electrochemical corrosion and tribological behavior of AA6063 aluminum composite fabricated using the stir casting technique and ECAP processing. The corrosion resistance of the composite improved with the addition of metallic reinforcement and after ECAP treatment. The wear resistance of the composite also significantly increased after ECAP processing.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article

Corrosion Behaviour of Mg, Graphite-, B4C and Ti-Reinforced Hybrid Aluminium Composites

Jigar Suthar et al.

Journal of The Institution of Engineers (India): Series C (2022)

Add to Collection

Article Electrochemistry

Investigation on the Microstructure and Electrochemical Corrosion Properties of TiB2 reinforced aluminum matrix composites

Qi-di Wu et al.

Summary: The TiB2 particles reinforced AlSi10Mg composites were prepared using selective laser melting (SLM) method, and the effect of TiB2 particles on the microstructure and electrochemical corrosion properties of Al-based composites was studied. The addition of TiB2 effectively improved the morphology of the molten pool and changed the corrosion type of the composites. The corrosion potential of the samples was positively shifted by adding TiB2, indicating an improved electrochemical stability. The corrosion resistance of the samples increased with the addition of TiB2, with the maximum resistance observed at 15% TiB2 content.

INTERNATIONAL JOURNAL OF ELECTROCHEMICAL SCIENCE (2022)

Add to Collection

Article

Investigation of Mechanical, Wear, and Corrosion Properties of Al–BN–SiC–RHA Hybrid Composites Synthesized Through Powder Metallurgy Process

G. R. Raghav et al.

METALLOFIZIKA I NOVEISHIE TEKHNOLOGII (2022)

Add to Collection

Article Chemistry, Physical

Tribological, Thermal and Corrosive Behaviour of Aluminium Alloy 2219 Reinforced by Si3N4 Nanosized Powder

C. J. Manjunatha et al.

Summary: By reinforcing the Al2219 aluminum alloy using high energy stir casting method with Si3N4 particles, it was found that the addition of Si3N4 significantly reduced wear and improved mechanical properties of the aluminum composites. Wear tests showed that with increasing reinforcement content, wear rate decreased.

SILICON (2022)

Add to Collection

Article Chemistry, Physical

Effect of SiC and MoS2 Co-reinforcement on Enhancing the Tribological and Anti-Corrosive Performance of Aluminum Matrix (Al6063-T6) Nanocomposites

N. Ramadoss et al.

Summary: Particulate reinforced aluminium matrix composites were prepared and their wear and corrosion properties were studied. The wear rates of the composites were lower than the base alloy at different applied loads, but the friction coefficients were higher. SEM micrographs revealed that particulates micro fracture was the predominant wear mechanism. The corrosion resistance was significantly improved in composites with SiC and MoS2 reinforcement, forming a protective layer to reduce corrosion rate.

SILICON (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on Corrosion Behaviour of LM25-SiCp Composite Using Taguchi Method

R. Suresh Kumar et al.

Summary: The aim of this investigation is to optimize the process parameters of Al/SiCp metal matrix composites to achieve minimum corrosion rate and weight loss. A Taguchi based grey relation analysis was conducted to determine the influential parameters on corrosion rate and weight loss.

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of interfacial bridging atoms on the strength of Al/CNT composites: machine-learning-based prediction and experimental validation

KeunWon Lee et al.

Summary: This study proposes a method to enhance the interfacial wetting between aluminum and CNTs by using bridging atoms, and uses machine learning and sensitivity analysis to determine copper as the most effective bridging atom. Experimental results validate the high strengthening efficiency of CNTs in the Al-Cu matrix, consistent with the prediction of the machine learning model.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article

Gravimetric, Electrochemical and Theoretical Study on Corrosion of AA6061/3wt% SiC/3wt% B4C Hybrid Composite in Acid Medium Using EDTA

J.D.E. Robledo et al.

Tribology in Industry (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Corrosion behavior of Al/TiO2/Y2O3 hybrid nanocomposites manufactured using the vacuum-assisted stir casting route

Mandeep Singh et al.

Summary: This study examined the corrosion and flexural behavior of advanced hybrid aluminum matrix nanocomposites reinforced with titanium oxide and yttrium oxide nanoparticles. The results showed that the addition of these nanoparticles improved the corrosion resistance and flexural strength of the composite materials, making them suitable for aerospace and automobile structural components.

ANTI-CORROSION METHODS AND MATERIALS (2022)

Add to Collection

Article Chemistry, Physical

Nanopowder derived Al/h-BN composites with high strength and

Shakti Corthay et al.

Summary: Al/h-BN composites with high strength and ductility were successfully obtained through ball milling and spark plasma sintering. The composites showed improved tensile and compressive properties at room and elevated temperatures. The combination of Al and h-BN nanoparticles resulted in enhanced strength and elongation to fracture, making the materials superior to other Al-based composites.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Surface Investigation of Physella Acuta Snail Shell Particle Reinforced Aluminium Matrix Composites

Catalin Iulian Pruncu et al.

Summary: Aluminium-matrix composites are highly desirable for various critical applications due to their lightweight nature and superior properties. In this study, Aluminium-matrix composites reinforced with Physella Acuta Snail Shell particles were developed using stir-casting method. The composites exhibited excellent performance in terms of tribological behavior, morphology, and corrosion resistance. Among the different compositions tested, the composite with 2% snail shell reinforcement (Al98SNS2) showed the best overall performance. The findings indicate that the inclusion of snail shell in aluminium-matrix composites promotes cost-effective, sustainable, and eco-friendly manufacturing.

COATINGS (2022)

Add to Collection

Article Materials Science, Ceramics

Effect of in-situ synthesized TiB2 on microstructure and mechanical property of Al/TiB2-SiC interpenetrating phase composites

Xin Zhang et al.

Summary: Al/TiB2-SiC composites were prepared using TiB2-SiC porous ceramic preforms, where in-situ synthesized TiB2 formed interconnected pores and ceramic skeletons. The structure and mechanical properties of the composites could be tailored by controlling the in-situ synthesized TiB2 volume fraction. Composite with 20 vol% TiB2 addition showed the optimum mechanical properties due to TiB2 additions and dense composite structures.

JOURNAL OF ASIAN CERAMIC SOCIETIES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

The influence of sustainable reinforcing particulates on the density, hardness and corrosion resistance of AA 6063 matrix composites

Ndudim Henry Ononiwu et al.

Summary: This study investigates the effect of sustainable materials on the mechanical, physical, and corrosion resistant properties of AA 6063. The hybrid reinforced aluminium matrix composites (AMCs) show improved mechanical and corrosion resistant properties compared to the base metal.

FRATTURA ED INTEGRITA STRUTTURALE-FRACTURE AND STRUCTURAL INTEGRITY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion behavior of nano-treated AA7075 alloy with TiC and TiB2 nanoparticles

Shuaihang Pan et al.

Summary: In this study, the corrosion performance of nano-treated AA7075 alloys was investigated, and it was found that nano-treatment can enhance the corrosion resistance of aluminum alloys, especially localized corrosion resistance.

CORROSION SCIENCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Characterization of Al/(TiC + TiB2) hybrid composites containing different amounts of MWCNTs produced by SPS

Seyed Majid Mirbagheri et al.

Summary: This study investigated the mechanical and corrosion properties of Al + 20 vol% (TiC + TiB2) composites containing different amounts of MWCNTs produced by mechanical alloying and spark plasma sintering processes. The results showed that the addition of MWCNTs improved the hardness, Young's modulus, and corrosion resistance of the composites.

JOURNAL OF MATERIALS RESEARCH (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Room and High Temperature Tensile Responses of Tib2-Graphene Al 7075 Hybrid Composite Processed through Squeeze Casting

N. Mathimurugan et al.

Summary: The development of aluminium composites with advanced materials, such as TiB2 and graphene, has been studied in this research. The aim of the study is to meet the increasing industrial demand for advanced hybrid materials. The research focuses on the development of Al 7075 alloy reinforced with TiB2 and graphene and evaluates its strengthening mechanism. The results show significant improvement in tensile and hardness compared to the base alloy. The fracture-morphology results indicate a change in fracture mode from brittle to ductile when the testing environment changes from room temperature to high temperature. The dispersion strengthening mechanism is validated with an empirical approach.

NANOMATERIALS (2022)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Effect of solid waste materials on properties of magnesium matrix composites-A systematic review

Fatih Aydin

Summary: The demand for light and high specific strength materials in automotive and aerospace industries is increasing. Magnesium-based materials are attractive due to their high specific strength, vibration damping ability, and recyclability. However, the low strength and wear resistance of magnesium limit its industrial use. Researchers are developing magnesium matrix composites using various reinforcements and exploring the use of cheaper and environmentally friendly options. This review focuses on magnesium matrix composites reinforced with solid waste particles and discusses the changes in wear, mechanical, corrosion, and thermal properties.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Multidisciplinary Sciences

An Investigate on Hot Wear and Corrosion Performance of Al Matrix Hybrid Composites Produced by Mechanical Alloying Method

Dogan Simsek

Summary: This study investigated the wear and corrosion behavior of ZrO2 and graphite reinforced aluminum matrix composites at different temperatures and in different corrosive environments. The results showed agglomeration of reinforcement material at grain boundaries, with wear and corrosion performance influenced by load and temperature.

ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2022)

Add to Collection

Article Engineering, Multidisciplinary

Wear performance of Al-TiC composite at elevated temperature

Eshan Agrawal et al.

Summary: The wear performance of Al-TiC composite with 7.5% reinforcement of TiC powder at elevated temperature was investigated in this study. The results showed that temperature had a dominant effect on the wear rate, and a mathematical model for wear rate and coefficient of friction at elevated temperatures was derived using the Taguchi method. The experimental results were conducted as per ASTM standards.

WORLD JOURNAL OF ENGINEERING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion behavior of nano-treated AA7075 alloy with TiC and TiB2 nanoparticles

Shuaihang Pan et al.

Summary: This study investigates the corrosion performance of nano-treated AA7075 alloys and reveals that nano-treating enhances the corrosion resistance of the material, particularly localized corrosion resistance. The interplays among microstructures, oxidation passivation, and corrosion were also highlighted.

CORROSION SCIENCE (2022)

Add to Collection

Article Chemistry, Physical

Influence of Ferrotitanium and Silicon Carbide Addition on Structural Modification, Nanohardness and Corrosion Behaviour of Stir-Cast Aluminium Matrix Composites

Samuel Olukayode Akinwamide et al.

Summary: The study investigated the microstructural, hardness, and corrosion properties of aluminium based composites reinforced with silicon carbide and ferrotitanium particles. The results showed that the reinforcements were uniformly dispersed within the aluminium matrix, leading to enhanced hardness properties and improved corrosion resistance.

SILICON (2021)

Add to Collection

Article Engineering, Chemical

The investigation of the effect of particle size on wear performance of AA7075/Al2O3 composites using statistical analysis and different machine learning methods

Fatih Aydin

Summary: Particle size and load are crucial factors influencing the wear performance of 7075-Al2O3 composites. A larger particle size and higher load lead to better wear resistance, with the 15 μm particle size composite showing the best performance. Machine learning models like ELM have high accuracy in predicting wear behavior for Al matrix composites.

ADVANCED POWDER TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Ceramics

Effect of ZrB2 on microstructural, mechanical and corrosion behaviour of aluminium (AA7178) alloy matrix composite prepared by the stir casting route

S. Dinesh Kumar et al.

Summary: A new class of aluminium alloy matrix composites reinforced with ZrB2 particles was developed using the bottom pouring type stir casting process. The addition of ZrB2 particles improved the mechanical and corrosion behaviors of the composites. Through electrochemical assessments and SEM analysis, the homogeneous distribution of ZrB2 particles and the enhanced corrosion resistance of the composites were demonstrated.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Compressive deformation and corrosion behaviour of moderate to highly porous Ti4Al4Co (wt%) alloy foam

Pradeep Singh et al.

Summary: The study investigated the effects of porosity on compressive deformation and corrosion behavior of porous Ti4Al4Co alloy foams. It was found that increasing porosity reduces the elastic modulus and energy absorption capacity, while densification strain increases linearly with porosity. Additionally, higher porosities were found to have a detrimental effect on the corrosion resistance of the material.

MATERIALS CHEMISTRY AND PHYSICS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Recent progress in graphene-reinforced aluminum matrix composites

Jinlong Su et al.

Summary: There is a growing interest in graphene-reinforced aluminum matrix composites (GRAMCs) due to the potential benefits it offers such as high strength, unique self-lubricating property, and high thermal and electrical conductivity. Studies have shown that adding graphene into aluminum or aluminum alloy can enhance the mechanical and physical properties of the material. This review traces the recent development of GRAMCs, covering fabrication methods, properties, and challenges faced by this type of composite material.

FRONTIERS OF MATERIALS SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigating the effect of mixing time on the crystallite size and lattice strain of the AA7075/TiC compositesEinfluss der Mischzeit auf die Kristallitgrosse und die Gitterverzerrung von AA7075/TiC-Verbundwerkstoffen

M. A. Alam et al.

Summary: The research investigates the impact of mixing time of matrix and reinforcement powders on the crystallite size and lattice strain of AA7075-5 wt.% TiC composites, showing that increasing mixing time can lead to improved crystallite size and microhardness, as well as reduce particle clustering and achieve uniform distribution of TiC particles in the composites.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK (2021)

Add to Collection

Article Materials Science, Composites

Investigation of the properties of Al7075-HTC composites produced by powder metallurgy

Ozan Arsun et al.

Summary: The study found that using hydrothermal carbons as reinforcement materials for Al 7075 alloy can improve its mechanical, tribological, and corrosion properties, making it a suitable reinforcement material for aluminium matrix composites.

JOURNAL OF COMPOSITE MATERIALS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Elevated-temperature high-strength h-BN-doped Al2014 and Al7075 composites: Experimental and theoretical insights

Shakti Corthay et al.

Summary: High-strength Al2014 and Al7075 series composites with h-BN additives were fabricated using HEBM and SPS, showing different phase compositions compared to standard alloys. The h-BN nanosheets provided solid lubrication, prevented agglomeration, and led to improved mechanical properties in the resultant composites, with an increase in hardness and tensile strength observed in samples with 3 wt% BN doping. Elevation in strength was attributed to the high thermal stability of reinforcing phases, solid solution hardening, and Orowan strengthening mechanisms.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Engineering, Mechanical

Wear resistance and tribological properties of GNPs and MWCNT reinforced AlSi18CuNiMg alloys produced by stir casting

Muhammet Emre Turan et al.

Summary: The study demonstrates that the addition of GNPs and MWCNTs reinforcements can significantly reduce the wear rates of the matrix, with graphene reinforced composite exhibiting the best tribological behavior. ANOVA indicates that the wear rate is mainly affected by material content, followed by sliding speed and applied load.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Microstructure and Corrosion Performance of Aluminium Matrix Composites Reinforced with Refractory High-Entropy Alloy Particulates

Elias Ananiadis et al.

Summary: Novel aluminium matrix composites reinforced by MoTaNbVW refractory high-entropy alloy (HEA) particulates were fabricated by powder metallurgy. The composites exhibited low porosity, good homogeneity, few defects, and good distribution of the reinforcing phase in the Al matrix. However, increasing the volume of the reinforcing phase led to increased hardness values, while the Al-HEA composites showed susceptibility to localised forms of corrosion in 3.5% NaCl solution.

APPLIED SCIENCES-BASEL (2021)

Add to Collection

Article Materials Science, Ceramics

Microstructure, wear and corrosion characteristics of multiple-reinforced (SiC-B4C-Al2O3) Al matrix composites produced by liquid metal infiltration

Kubilay Ozturk et al.

Summary: Increasing the amount of Al2O3 leads to better infiltration, reduced porosity, and predominantly abrasive and adhesive wear.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolutions and mechanical properties of multilayered 1060Al/Al-Al2O3 composites fabricated by cold spraying and accumulative roll bonding

Xiaohan Dang et al.

Summary: A multiple processing technique combining cold spraying and accumulative roll bonding was used to prepare multilayered 1060Al/AleAl(2)O(3) composites with improved ductility. The microstructural evolution, tensile properties, and fracture behavior of the composite were analyzed to understand the mechanisms behind the high strength and ductility achieved through optimized processing. Analysis of microstructural features provided insights into the underlying mechanisms explaining the improved mechanical properties.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Chemistry, Physical

Degradation mechanism of 6063 aluminium matrix composite reinforced with TiC and Al2O3 particles

Min Ao et al.

Summary: The addition of TiC and Al2O3 particles refines the grain structure of the composite material and increases the AlFeSi phase content, but reduces the corrosion resistance of the composite material.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Metallurgical Characteristics, Compressive Strength, and Chemical Degradation Behavior of Aluminum-Cenosphere Composite Foam Developed by Spray Forming Route

Amarish Kumar Shukla et al.

Summary: This study investigated the microstructural characteristics, compressive strength, and corrosion behavior of aluminum-cenosphere composite foam developed by spray forming route. The compressive yield strength of CF differed from commercially pure aluminum, and the corrosion rate of CF was significantly reduced compared to cp-Al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Homogeneously Dispersed Graphene Nanoplatelets as Long-Term Corrosion Inhibitors for Aluminum Matrix Composites

Yuming Xie et al.

Summary: Deformation-driven metallurgy was used to prepare graphene nanoplatelet-reinforced aluminum matrix composites, resulting in enhanced corrosion resistance through severe plastic deformation and homogeneously dispersed graphene nanoplatelets. The formation of a carbon-doped protective film in a chloride-containing environment contributed to the great corrosion inhibition mechanism of the composites.

ACS APPLIED MATERIALS & INTERFACES (2021)

Add to Collection

Article

Corrosion Behavior of Al/SiC Composite Prepared by Powder Metallurgy in Chloride Environments

Sahib M. Mahdi et al.

Journal of Bio- and Tribo-Corrosion (2021)

Add to Collection

Article Materials Science, Composites

Influence of GNPs and B4C reinforcements on mechanical, thermal and wear properties of magnesium matrix composite produced by powder metallurgy

Yavuz Sun et al.

Summary: The study showed that adding boron carbide and graphene nanoplatelets can significantly increase the hardness, yield strength, and tensile strength of pure magnesium. Composite samples exhibited better wear resistance compared to unreinforced samples, but thermal conductivity decreased with the addition of B4C reinforcements. Additionally, the level of porosity was higher in the composite samples.

JOURNAL OF COMPOSITE MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of Elevated Temperature Wear Behavior of Al 2024-BN Composites using Statistical Techniques

Fatih Aydin

Summary: This study investigated the elevated temperature wear behavior of 2024 aluminum matrix composites reinforced with different amounts of BN particles, manufactured by hot pressing. The results showed that the addition of 2% BN particles significantly improved the wear performance of the composites under high temperature conditions. Additionally, regression equations were established to predict the wear rate, with nonlinear regression achieving the highest success rate with a determination coefficient of 91.5%.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Mechanical properties of aluminium-graphene/carbon nanotubes (CNTs) metal matrix composites: Advancement, opportunities and perspective

Virat Khanna et al.

Summary: The rapid development of the mechanical industry requires new and reliable materials, with Metal Matrix Composites (MMCs) being one of the prominent candidates. Carbon nanostructures, such as graphene and carbon nanotubes (CNTs), are found to be excellent support reinforcement materials in MMCs. The study evaluates the impact of graphene/CNTs reinforcement in aluminum for improvement in mechanical properties, as well as reviewing different processing methods.

MATERIALS RESEARCH BULLETIN (2021)

Add to Collection

Article Chemistry, Physical

Corrosion Resistance of Al-CNT Metal Matrix Composites

Vladimir V. Popov et al.

Summary: Aluminium-graphite metal matrix composites (MMCs) with advanced mechanical properties and high corrosion resistance are in demand for aerospace, transportation, and industrial applications. Breakthroughs in this field are limited due to the tendency of aluminium-graphite MMCs to corrode. The addition of multiwall carbon nanotubes (MWCNTs) into molten aluminium and processing through high-pressure die casting and cyclic extrusion has shown improved mechanical properties in comparison with pure aluminium alloys. Additionally, experimental testing of the corrosion resistance of Al-MWCNT MMCs demonstrated that the addition of MWCNTs does not significantly decrease the corrosion resistance due to the advantages of the fabrication method.

MATERIALS (2021)

Add to Collection

Review Engineering, Manufacturing

A review on microstructures and properties of graphene-reinforced aluminum matrix composites fabricated by friction stir processing

Huijie Zhang et al.

Summary: Graphene is an ideal reinforcement for the fabrication of aluminum matrix composites (AMCs), and Friction Stir Processing (FSP) is an ideal candidate for producing high-performance graphene-reinforced AMCs. The addition of graphene affects the structure and properties evolution of AMCs, while process conditions and microstructure evolutions also play a critical role in determining the properties of the composites.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Effect of processing speed on wear and corrosion behavior of novel MoS2 and CeO2 reinforced hybrid aluminum matrix composites fabricated by friction stir processing

Pabitra Maji et al.

Summary: The use of MoS2 and CeO2 powder reinforcement in Al7075 alloy through friction stir processing results in improved microstructural properties. Lower processing speed and increased number of passes lead to reduced grain size, improved particle distribution, higher microhardness, and tensile strength. Composites with lower processing speed and multi-pass exhibit lower friction coefficient and wear loss, while composites with higher speed and passes show deteriorated corrosion behavior. The composite produced with 30 mm/min and 2 pass displays the best particle distribution, microhardness, and wear resistance, while the one with 30 mm/min and 1 pass shows the best corrosion resistance.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Investigation of Corrosion Behaviors of Al-B4C-reinforced Composite Materials in Different Antifreeze Solutions

Ijlal Simsek

Summary: This study investigates the corrosion behaviors of composite materials containing varied amounts of B4C in different concentrations of antifreeze environments. The hardness of the materials increases with higher B4C content while the density decreases, leading to reduced corrosion resistance as observed in the tests. The highest corrosion resistance was found in the aluminum matrix composite in 100% antifreeze solution.

PROTECTION OF METALS AND PHYSICAL CHEMISTRY OF SURFACES (2021)

Add to Collection

Review Materials Science, Multidisciplinary

A review on recent developments of aluminum-based hybrid composites for automotive applications

Rohit Chandel et al.

Summary: The automotive sector is driven by the need for lightweight and efficient vehicles due to increased fuel costs and emission standards. Aluminum-based hybrid composites have been identified as promising alternatives to traditional alloys, with the potential to improve mechanical properties and reduce fuel consumption. The addition of reinforcement particles, both hard and soft, has been found to enhance strength, hardness, and wear resistance, demonstrating the potential for ceramic particulates and agricultural waste derivatives as secondary reinforcements.

EMERGENT MATERIALS (2021)

Add to Collection

Article Electrochemistry

Corrosion and Hardness Behaviour of Al/GO Nanocomposites Processed by the Ultrasonic Gravitational Stir Casting Method

S. Narayanan et al.

Summary: The corrosion behavior of nanographene oxide reinforced aluminum metal matrix composites was evaluated with different immersion time periods, showing that corrosion rate decreased and weight losses increased with longer immersion times. The nonimmersed composites exhibited higher microhardness values compared to the immersed ones.

INTERNATIONAL JOURNAL OF CORROSION (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of TiB2 on the Corrosion Resistance Behavior of In Situ Al Composites

P. Senthil Kumar et al.

INTERNATIONAL JOURNAL OF METALCASTING (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Aluminum Matrix Composites Reinforced with Graphene: A Review on Production, Microstructure, and Properties

Nima Seyed Pourmand et al.

CRITICAL REVIEWS IN SOLID STATE AND MATERIALS SCIENCES (2020)

Add to Collection

Article Materials Science, Composites

Influence of TiC content on mechanical, wear and corrosion properties of hot-pressed AZ91/TiC composites

Fatih Aydin et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

Add to Collection

Article Materials Science, Composites

The effect of high TiC particle content on the tensile cracking and corrosion behavior of Al-5Cu matrix composites

Burak Dikici et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

Add to Collection

Review Chemistry, Physical

Tensile properties of carbon nanotubes reinforced aluminum matrix composites: A review

M. Jagannatham et al.

CARBON (2020)

Add to Collection

Review Engineering, Mechanical

Microstructural, mechanical and wear characteristics of aluminum matrix composites fabricated by friction stir processing

Pabitra Maji et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2020)

Add to Collection

Article Materials Science, Composites

Investigation of Microstructural, Mechanical and Corrosion Properties of AA7010-TiB2 in-situ Metal Matrix Composite

Naresh Mallireddy et al.

SCIENCE AND ENGINEERING OF COMPOSITE MATERIALS (2020)

Add to Collection

Review Engineering, Manufacturing

A review on fabrication methods, reinforcements and mechanical properties of aluminum matrix composites

Vineet Chak et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Effect of Friction Stir Welding Parameters on Microstructure and Properties of Welded 5083 Aluminium Alloy

Lixin Hao et al.

JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of manufacturing parameters on the corrosion behavior of Al-B4C nanocomposites

Mohammad Arab et al.

MATERIALS CHEMISTRY AND PHYSICS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Processing Methods and Mechanical Properties of Aluminium Matrix Composites

Gebre Fenta Aynalem

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

In-situ nanoscopic observations of dealloying-driven local corrosion from surface initiation to in-depth propagation

A. Kosari et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Kinetics and dynamics of surface thermal oxidation in Al-ZrB2 nanocomposites

Shuaihang Pan et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Multidisciplinary Sciences

Corrosion, mechanical and thermal properties of aluminium alloy metal matrix nano composites (AA-MMNCs) with multi-walled carbon nanotubes

A. Jayaraj et al.

SN APPLIED SCIENCES (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructural Characteristics, Mechanical Properties, Fracture Analysis and Corrosion Behavior of Hypereutectic Al-13.5Si Alloy

Jelena Scepanovic et al.

INTERNATIONAL JOURNAL OF METALCASTING (2019)

Add to Collection

Article Materials Science, Ceramics

The Effect of TiB2 Content on Wear and Mechanical Behavior of AZ91 Magnesium Matrix Composites Produced by Powder Metallurgy

Fatih Aydin et al.

POWDER METALLURGY AND METAL CERAMICS (2019)

Add to Collection

Article Materials Science, Composites

Investigation of wear and corrosion behavior of graphene nanoplatelet-coated B4C reinforced Al-Si matrix semi-ceramic hybrid composites

Safa Polat et al.

JOURNAL OF COMPOSITE MATERIALS (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Advance research progresses in aluminium matrix composites: manufacturing & applications

Pulkit Garg et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

The corrosion behavior of chromated AA2024 aluminum alloy in 3.5% NaCl solution

Yong Zhou et al.

ANTI-CORROSION METHODS AND MATERIALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical study of the surface metal matrix composite developed on AA 2024-T351 by the friction stir process

R. Acuna et al.

CORROSION ENGINEERING SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical, tribological, and electrochemical behavior of hybrid aluminum matrix composite containing boron carbide (B4C) and graphene nanoplatelets

Qaisar Abbas Shafqat et al.

JOURNAL OF MATERIALS RESEARCH (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and corrosion behavior of Al-TiB2/TiC composites processed by hot rolling

Jinfeng Nie et al.

RESULTS IN PHYSICS (2019)

Add to Collection

Article Chemistry, Physical

Microstructure and synergistic reinforcing activity of GNPs-B4C dual-micro and nano supplements in Al-Si matrix composites

Safa Polat et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of microstructural, mechanical and corrosion properties of graphene nanoplatelets reinforced Al matrix composites

Nazli Akcamli et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Automation & Control Systems

Investigation of the influence of SiC content and particle size variation on the corrosion resistance of Al-SiC matrix composite in neutral chloride solution

Roland Tolulope Loto

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Characterization of Pulse and Direct Current Methods for Electrodeposition of Ni-Co Composite Coatings Reinforced with Nano and Micro ZnO Particles

Siavash Imanian Ghazanlou et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)

Add to Collection

Article Electrochemistry

On the Impact of Si Content and Porosity Artifacts on the Anodizing Behavior of Additive Manufactured Al-Si Alloys

Reynier Revilla et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

The effects of graphene content on the corrosion resistance , and electrical , thermal and mechanical properties of graphene/copper composites

Wang Jian et al.

NEW CARBON MATERIALS (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and properties of pure aluminum prepared by spark plasma sintering

Wen Zeng et al.

METALLURGICAL RESEARCH & TECHNOLOGY (2019)

Add to Collection

Review Engineering, Manufacturing

Processing issues, machining, and applications of aluminum metal matrix composites

Jigar Suthar et al.

MATERIALS AND MANUFACTURING PROCESSES (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Role of cerium in microstructure and corrosion properties of Sn-1.0Ag solder alloys

B. X. Vuong et al.

MATERIALS LETTERS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of carbonaceous reinforcements on microstructure and corrosion properties of magnesium matrix composites

Muhammet Emre Turan et al.

MATERIALS CHEMISTRY AND PHYSICS (2018)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Investigation on mechanical properties or aluminium 7075-boron carbide - coconut she fly ash reinforced hybrid metal matrix composites

Balasubramani Subramaniam et al.

CHINA FOUNDRY (2018)

Add to Collection

Article Engineering, Multidisciplinary

Analysis of SiC grain size variation and NaCl concentration on the corrosion susceptibility of AA1070 aluminium matrix composites

Roland Tolulope Loto et al.

COGENT ENGINEERING (2018)

Add to Collection

Article Electrochemistry

Heat Treatment Degrading the Corrosion Resistance of Selective Laser Melted Ti-6Al-4V Alloy

Nianwei Dai et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical evaluation of sintered aluminium - ceramic cenospheres composites

C. A. Vogiatzis et al.

CORROSION ENGINEERING SCIENCE AND TECHNOLOGY (2017)

Add to Collection

Article Chemistry, Physical

Effect of silicon carbide addition on the corrosion behavior of powder metallurgy Cu-30Zn brass in a 3.5 wt% NaCl solution

Mohammed Ali Almomani et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Article Materials Science, Characterization & Testing

Processing and characterization of graphene nano-platelet (GNP) reinforced aluminum matrix composites

Nazli Akcamli et al.

MATERIALS TESTING (2016)

Add to Collection

Article Engineering, Environmental

Super-hydrophobic nickel-cobalt alloy coating with micro-nano flower-like structure

S. Khorsand et al.

CHEMICAL ENGINEERING JOURNAL (2015)

Add to Collection

Article Chemistry, Physical

Salt spray corrosion and electrochemical corrosion properties of anodic oxide film on 7475 aluminum alloy

Kong Dejun et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion behavior of Al-Mg2Si alloys with/without addition of Al-P master alloy

Zedi Li et al.

MATERIALS CHARACTERIZATION (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on microstructural, mechanical and electrochemical properties of aluminum composites reinforced with graphene nanoplatelets

Muhammad Rashad et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2015)

Add to Collection

Article Chemistry, Physical

Electrochemical Behavior of Al-B4C Metal Matrix Composites in NaCl Solution

Yu-Mei Han et al.

MATERIALS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of Corrosion Behaviour of Aluminium Alloy Subjected to Laser Shock Peening without a Protective Coating

U. Trdan et al.

ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation on microstructural, mechanical and electrochemical properties of aluminum composites reinforced with graphene nanoplatelets

Muhammad Rashad et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Microhardness and corrosion properties of hypoeutectic Al-7Si alloy processed by high-pressure torsion

Xue Wang et al.

MATERIALS & DESIGN (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics

Michael Oluwatosin Bodunrin et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2015)

Add to Collection

Article Electrochemistry

Chloride Ion Interactions with Oxide-Covered Aluminum Leading to Pitting Corrosion: A Review

P. M. Natishan et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2014)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Characteristics and wear behavior of cenosphere dispersed titanium matrix composite developed by powder metallurgy route

D. P. Mondal et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2014)

Add to Collection

Article Engineering, Multidisciplinary

Microstructural and corrosion behavior of Al/SiC metal matrix composites

H. M. Zakaria

AIN SHAMS ENGINEERING JOURNAL (2014)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Corrosion and wear behaviour of rice husk ash—Alumina reinforced Al–Mg–Si alloy matrix hybrid composites

Kenneth Kanayo Alaneme et al.

Journal of Materials Research and Technology-JMR&T (2013)

Add to Collection

Proceedings Paper Energy & Fuels

Synthesis and characterization of Al6061-Fly Ashp-SiCp composites by stir casting and compocasting methods

David Raja J. Selvam et al.

10TH ECO-ENERGY AND MATERIALS SCIENCE AND ENGINEERING SYMPOSIUM (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical study of Aluminum-Fly Ash composites obtained by powder metallurgy

E. Marin et al.

MATERIALS CHARACTERIZATION (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Reinforcement with graphene nanosheets in aluminum matrix composites

Jingyue Wang et al.

SCRIPTA MATERIALIA (2012)

Add to Collection

Article Engineering, Multidisciplinary

Ultrasound assisted in situ technique for the synthesis of particulate reinforced aluminum matrix composites

Zhiwei Liu et al.

COMPOSITES PART B-ENGINEERING (2011)

Add to Collection

Article Chemistry, Analytical

Fabrication of exfoliated graphite nanoplatelets-reinforced aluminum composites and evaluating their mechanical properties and corrosion behavior

F. H. Latief et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2011)

Add to Collection

Review Materials Science, Multidisciplinary

Effect of Grain Size on Corrosion: A Review

K. D. Ralston et al.

CORROSION (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Grain character influences on corrosion of ECAPed pure magnesium

N. Birbilis et al.

CORROSION ENGINEERING SCIENCE AND TECHNOLOGY (2010)

Add to Collection

Article Electrochemistry

Effects of severe plastic deformation on the corrosion behavior of aluminum alloys

Eiji Akiyama et al.

JOURNAL OF SOLID STATE ELECTROCHEMISTRY (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical corrosion behavior of Al-Si alloy composites reinforced with in situ TiB2 particulate

H. H. Sun et al.

MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION (2009)

Add to Collection

Article Chemistry, Physical

Novel Al-matrix nanocomposites reinforced with multi-walled carbon nanotubes

R. Perez-Bustamante et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2008)

Add to Collection

Article Materials Science, Coatings & Films

Fabrication and analysis of anti-corrosion coatings on in-situ TiB2p reinforced aluminum matrix composite

Huanhuan Sun et al.

SURFACE & COATINGS TECHNOLOGY (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion characteristics of hybrid Al/SiCp/MgAl2O4 composites fabricated with fly ash and recycled aluminum

R. Escalera-Lozano et al.

MATERIALS CHARACTERIZATION (2007)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of Ce surface treatments on corrosion behaviour of A3xx.x/SiCp composites in 3.5wt.% NaCl

A. Pardo et al.

CORROSION SCIENCE (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of reinforcement proportion and matrix composition on pitting corrosion behaviour of cast aluminium matrix composites (A3xx.x/SiCp)

A Pardo et al.

CORROSION SCIENCE (2005)

Add to Collection

Review Electrochemistry

From Bacon to barriers: a review on the passivity of metals and alloys

P Schmuki

JOURNAL OF SOLID STATE ELECTROCHEMISTRY (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.