☆ 4.7 Article

Microstructure and mechanical properties of CuCrZr/316L hybrid components manufactured using selective laser melting

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Single and multiple track formation mechanism of laser powder bed fusion 316L/CuSn10 multi-material

Jie Chen et al.

Summary: The study found that the width of the single-track is affected by laser power, layer thickness, and scanning speed, while variations in copper content and wetting angle of the molten pool were also investigated. Additionally, scanning speed and layer thickness have a greater impact on the formation of single cracks.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Chemistry, Physical

Effects of process parameters on interfacial characterization and mechanical properties of 316L/CuCrZr functionally graded material by selective laser melting

Shenglan Mao et al.

Summary: Steel-Copper functionally graded material (FGM) fabricated by selective laser melting (SLM) has been studied for its interfacial characteristics, microscopic features, tensile properties, and microhardness, with a processing map developed for CuCrZr tracks on SLM processed 316L substrate. The study found that specific process parameters are suitable for the formation of 316L/CuCrZr FGM, with improvements in ultimate tensile strengths and microhardness in different regions of the material. These findings offer valuable guidance for the fabrication of Steel-Copper FGM by SLM.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Preparation of Cu-Cr-Zr alloy by selective laser melting: Role of scanning parameters on densification, microstructure and mechanical properties

Zhangping Hu et al.

Summary: The evolution of microstructure and mechanical properties of Cu-Cr-Zr fabricated by selective laser melting (SLM) with different scanning parameters was investigated. Cu-Cr-Zr specimens with high density and superior mechanical properties were obtained by optimizing the scanning parameters. The anisotropic trend of crystallographic texture and grain microstructure was observed in different planes, and the formation of twins and nano precipitates contributed to the excellent mechanical properties of the specimens.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Chemistry, Physical

Microstructure evaluation and resultant mechanical properties of laser- arc hybrid additive manufactured Cu-Cr-Zr alloy

Guangyi Ma et al.

Summary: This study investigated laser-arc hybrid additive manufacturing (LAHAM) of Cu-Cr-Zr alloy and compared it with wire arc additive manufacturing (WAAM). LAHAM samples showed refined grain size, reduced texture index and pole density intensity compared to WAAM samples. The LAHAM copper alloy exhibited improved tensile properties, with increased ultimate strength and elongation.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Selective laser melting of CuCrZr alloy: processing optimisation, microstructure and mechanical properties

Zezhou Kuai et al.

Summary: The process parameters characteristics of CuCrZr alloy processed by selective laser melting (SLM) were systematically investigated. The laser power and scanning speed were found to have an effect on the surface morphology of the samples, while the scanning strategy influenced the densification level. By optimizing the process parameters, almost fully dense CuCrZr samples with stable melt tracks and no obvious porosity were obtained. The grain morphology and orientation were highly correlated with the laser trajectory and construction direction. XRD analysis showed the presence of diffraction peaks of α-Cu and no peaks of other phase components.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Chemistry, Physical

A study on the mechanical and electrical properties of high-strength CuCrZr alloy fabricated using laser powder bed fusion

Xiangpeng Tang et al.

Summary: In this study, CuCrZr alloys were successfully fabricated using laser powder bed fusion with a short wave-length laser, and excellent mechanical properties and improved conductivity were achieved through direct aging treatment.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

CuCrZr alloy produced by laser powder bed fusion: Microstructure, nanoscale strengthening mechanisms, electrical and mechanical properties

C. Salvan et al.

Summary: CuCrZr alloy is manufactured using laser powder bed fusion process, and after appropriate heat treatment, it can achieve excellent mechanical and electrical properties, mainly due to the combination of high concentration of Cr nano-precipitates and high dislocation density along with the presence of remaining solidification cells.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Chemistry, Physical

On the role of laser in situ re-melting into pore elimination of Ti-6Al-4V components fabricated by selective laser melting

Fei Lv et al.

Summary: The study proposes a mesoscale model to reveal the pore elimination mechanism in Ti-6Al-4V alloy during laser re-melting process. It is found that an appropriate re-melting scanning speed can effectively improve the material density and surface quality.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of input energy on hardness and surface quality in Ti64 by sputter-less selective laser melting with modulated pulse

Yuta Mizuguchi et al.

Summary: By employing a modulated pulse of laser to control the heat input energy in the SLM process, the crystal orientation and grain size of a titanium alloy Ti64 were successfully controlled, resulting in different Vickers hardness values.

JOURNAL OF LASER APPLICATIONS (2021)

Add to Collection

Article Engineering, Aerospace

End to end process evaluation for additively manufactured liquid rocket engine thrust chambers

Fabio Kerstens et al.

Summary: This paper provides a detailed review on the state-of-the-art, challenges, and opportunities for designing additively manufactured liquid rocket engines using laser powder bed fusion or directed energy deposition techniques. It explores how additive manufacturing can open up new possibilities for engine design, leading to more competitive designs. The study explains the steps involved in creating additively manufactured thrusters, including process considerations, AM techniques, and post-processing operations.

ACTA ASTRONAUTICA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Additively manufactured CuCrZr alloy: Microstructure, mechanical properties and machinability

Yuchao Bai et al.

Summary: Manufacturing CuCrZr alloy parts with high strength and high surface quality by selective laser melting (SLM) is challenging. The study found that after heat treatment, the grain morphology of the alloy changed, with slender and bent grains on the XY plane being replaced by polygonal square grains, while large epitaxial grains on the XZ plane remained.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Preparation of Cu-Cr-Zr Alloy by Laser Powder Bed Fusion: Parameter Optimization, Microstructure, Mechanical and Thermal Properties for Microelectronic Applications

Xiangyao Fang et al.

Summary: LPBF technology was used to successfully fabricate Cu-Cr-Zr alloy with high density and hardness, featuring Cr spherical precipitates in the microstructure and significant anisotropy in Vickers hardness. The heat sinks made from Cu-Cr-Zr alloy exhibited high heat transfer coefficients, with the cylindrical micro-needle heat sink showing the best heat dissipation performance.

METALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Zr-containing precipitate evolution and its effect on the mechanical properties of Cu-Cr-Zr alloys

Yibo Du et al.

Summary: The Zr-containing precipitates in the Cu alloy first form coherent Zr-rich atomic clusters on the {111} crystal plane of copper during aging, which then transform into Cu5Zr phase as aging time increases. The contribution of Zr-rich atomic clusters and Cu5Zr precipitates to the yield strength of the alloy is calculated by coherency strengthening and Orowan strengthening, respectively. The total yield strength is very close to the experimentally measured strength.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced hardness and moderate thermal conductivity of Cu-2.4Ni-0.7Si alloy processed via selective laser melting followed by suitable heat treatment

Yan Zhou et al.

JOURNAL OF LASER APPLICATIONS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Lattice structures of Cu-Cr-Zr copper alloy by selective laser melting: Microstructures, mechanical properties and energy absorption

Zhibo Ma et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Influence mechanism of process parameters on the interfacial characterization of selective laser melting 316L/CuSn10

Jie Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Chemistry, Physical

Selective laser melting of Cu-Cr-Zr copper alloy: Parameter optimization, microstructure and mechanical properties

Zhibo Ma et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Engineering, Industrial

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property

Keyu Chen et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Dual interfacial characterization and property in multi-material selective laser melting of 316L stainless steel and C52400 copper alloy

Yuchao Bai et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Chemistry, Physical

Mechanical Properties of High-Strength Cu-Cr-Zr Alloy Fabricated by Selective Laser Melting

Fujia Sun et al.

MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and properties of high strength and high conductivity Cu-Cr alloy components fabricated by high power selective laser melting

Shasha Zhang et al.

MATERIALS LETTERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of CuSn/18Ni300 bimetallic porous structures manufactured by selective laser melting

Mingkang Zhang et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Chemistry, Physical

Thermal effect on the microstructure of the lattice structure Cu-10Sn alloy fabricated through selective laser melting

Zhen Tan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Chemistry, Physical

Microstructure and properties of CuCr alloy manufactured by selective laser melting

Yuhong Chen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Interfacial microstructure and mechanical. properties of 316L /CuSn10 multi-material bimetallic structure fabricated by selective laser melting

Jie Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of heat treatments on microstructure and properties of CuCrZr produced by laser-powder bed fusion

Christopher Wallis et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Engineering, Industrial

Hybrid additive manufacturing of Al-Ti6Al4V functionally graded materials with selective laser melting and cold spraying

Shuo Yin et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution of copper/steel gradient deposition prepared using electron beam freeform fabrication

Xi Shu et al.

MATERIALS LETTERS (2018)

Add to Collection

Review Materials Science, Multidisciplinary

Additive manufacturing of multi-material structures

Amit Bandyopadhyay et al.

MATERIALS SCIENCE & ENGINEERING R-REPORTS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Additive manufacturing of Zr-based metallic glass structures on 304 stainless steel substrates via V/Ti/Zr intermediate layers

Yingqi Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Selective laser melting of lattice structures: A statistical approach to manufacturability and mechanical behavior

Swee Leong Sing et al.

ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Interfacial characteristic and mechanical performance of maraging steel-copper functional bimetal produced by selective laser melting based hybrid manufacture

Chaolin Tan et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Improved corrosion behavior of ultrafine-grained eutectic Al-12Si alloy produced by selective laser melting

Yan Yang et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure prediction of selective laser melting AlSi10Mg using finite element analysis

Shiwen Liu et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Materials Science, Multidisciplinary

The printability, microstructure, crystallographic features and microhardness of selective laser melted Inconel 718 thin wall

Huihui Yang et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Engineering, Biomedical

Improving the fatigue performance of porous metallic biomaterials produced by Selective Laser Melting

Brecht van Hooreweder et al.

ACTA BIOMATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Laser Powder Bed Fusion - Materials Issues and Optimized Processing Parameters for Tool steels, AlSiMg- and CuCrZr-Alloys

Bruno Buchmayr et al.

ADVANCED ENGINEERING MATERIALS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Additive manufacturing of metals

Dirk Herzog et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of LMD-SLM hybrid forming Ti6A14V alloy

Qi Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Joining of Inconel 718 and 316 Stainless Steel using electron beam melting additive manufacturing technology

Alejandro Hinojos et al.

MATERIALS & DESIGN (2016)

Add to Collection

Proceedings Paper Engineering, Manufacturing

New possibilities in the fabrication of hybrid components with big dimensions by means of selective laser melting (SLM)

A. Ascari et al.

LASER ASSISTED NET SHAPE ENGINEERING 9 INTERNATIONAL CONFERENCE ON PHOTONIC TECHNOLOGIES PROCEEDINGS OF THE LANE 2016 (2016)

Add to Collection

Review Materials Science, Multidisciplinary

Laser additive manufacturing of metallic components: materials, processes and mechanisms

D. D. Gu et al.

INTERNATIONAL MATERIALS REVIEWS (2012)

Add to Collection

© Peeref 2019-2024. All rights reserved.