☆ 4.7 Article

Synchronous-hammer-forging-assisted wire arc additive manufacturing Al-Mg alloy

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Direct additive manufacturing of TiCp reinforced Al2O3-ZrO2 eutectic functionally graded ceramics by laser directed energy deposition

Dongjiang Wu et al.

Summary: Laser directed energy deposition (LDED) was used to manufacture TiCp reinforced Al2O3-ZrO2 eutectic functionally graded ceramics with two different transition modes for the first time. The results show that the gradient transition leads to a gradual increase of TiCp particles in the Al2O3-ZrO2 eutectic matrix. With increased TiCp content, the morphology of the eutectic matrix changes from lamellar or rod-shaped to irregular shape. LDED also enables controllable fabrication of properties in different positions of the gradient materials, with a 43.4% increase in wear resistance in TiCp rich regions compared to pure Al2O3-ZrO2 region.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Engineering, Manufacturing

Investigate the effect of arc characteristic on the mechanical properties of 5A56 Al alloy in CMT arc additive manufacturing

Liang Zhang et al.

Summary: This study investigates the effect of arc characteristic on the mechanical properties of 5A56 Al alloy in wire arc additive manufacturing (WAAM). Three different arc processes (CMT, CMT-VP, and CMT-P) were used, and their impact on arc behavior, droplet transfer, heat input, microstructure, and mechanical properties were analyzed. The CMT-VP process exhibited better thermal management ability with higher deposition rate and well-formed specimens. The microstructure of CMT-VP specimens had finer and more uniform equiaxed grains, leading to improved mechanical properties compared to CMT and CMT-P processes.

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2023)

Add to Collection

Article Chemistry, Physical

Mechanism of grain refinement and mechanical property enhancement of Ti-45Al-8Nb alloy by directed laser deposition

Tengda Di et al.

Summary: This paper investigates the interactions between semi-coherent interfaces, deformation twins, and dislocations in Ti-45Al-8Nb alloy specimens manufactured by DLD. The results reveal the strengthening mechanism of interlamellar spacing on mechanical properties and indicate that laser power is an important factor affecting the interlamellar spacing. By adjusting the laser power, the interlamellar spacing decreases by 40.1%, leading to increased microhardness and tensile strength of the alloy. The obstruction and absorption of dislocation motion by the lamellar interface and deformation twins contribute to the improved mechanical properties.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

In-situ observation of microcrack initiation and damage nucleation modes on the HAZ of laser-welded DP1180 joint

Junliang Xue et al.

Summary: In-situ SEM is used to observe microstructural and microcrack changes in the deformation process. This paper discusses the microstructural evolution, mechanical properties, and damage nucleation modes of DP1180 laser welded joints using TEM, FIB, and in-situ tensile test. The mechanical properties of tempered martensite in the sub-critical heat affected zone (SCHAZ) were deteriorated due to the precipitation of carbides and disappearance of dislocations tangles, resulting in slight decrease in microhardness (approximately 27HV) and the development of a softened zone. Microcracks initiated from tempered martensite in the SCHAZ while microcrack initiation of the base material occurred at the ferrite/martensite interface. Tempered martensite cracking was the dominant damage nucleation mode in the joint, while ferrite/martensite interface decohesion was the dominant mode in the base material.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Long-lasting action mechanism of 3D skeleton regulated the residual stress fluctuations in SiCf/SiC heterogeneous joints

Yu Zhang et al.

Summary: SiCf/SiC composites can improve the operating temperature and thrust-weight ratio of aero-engines, and their effective joining with superalloys can solve the problem of poor machinability. In this study, graphene-reinforced Cu (G-Cu) foam was introduced as an energy-absorbing interlayer to relieve the residual stress in the brazed joint. The G-Cu foam played a protective role, and its foam structure remained intact, leading to good microstructure and improved performance.

MATERIALS CHARACTERIZATION (2023)

Add to Collection

Article Engineering, Civil

Surface morphology, microstructure and mechanical properties of Al-Mg-Sc alloy thin wall produced by laser-arc hybrid additive manufacturing

Shengchong Ma et al.

Summary: This study develops a wire-based process of laser-arc hybrid additive manufacturing (LHAM) to fabricate aluminum alloys containing Sc. Compared with wire and arc additive manufacturing (WAAM) under two processing conditions, LHAM shows significantly improved surface quality and refined microstructure. LHAM also exhibits a higher and more stable microhardness distribution and exceptional elongation, indicating less anisotropy in mechanical properties.

THIN-WALLED STRUCTURES (2023)

Add to Collection

Article Materials Science, Ceramics

One-step additive manufacturing of TiCp reinforced Al2O3-ZrO2 eutectic ceramics composites by laser directed energy deposition

Dongjiang Wu et al.

Summary: Laser directed energy deposition (LDED) is used to fabricate TiCp-reinforced Al2O3-ZrO2 eutectic ceramics, with different ratios of TiCp percentage investigated on their inhibitory mechanism on crack and porosity defects. The distribution of TiCp particles and the microstructure around them are influenced by the solidification rate. The mismatch of thermal expansion coefficient and elastic modulus between TiCp and Al2O3-ZrO2 eutectic matrix causes crack pinning and transgranular, while TiCp doping enhances molten pool impact and reduces porosity.

CERAMICS INTERNATIONAL (2023)

Add to Collection

Article Automation & Control Systems

Comparative investigation of wire arc additive manufacturing of Al-5%Mg alloy with and without external alternating magnetic field

Wenyong Zhao et al.

Summary: In this investigation, an external longitudinal alternating magnetic field is introduced into the wire arc additive manufacturing system to optimize the fabrication quality of aluminum alloy. The study comprehensively examines the effects of the external magnetic field on the arc behavior, metal transfer, deposit morphology, microstructure, and mechanical properties of the WAAM process. The results show that the excitation current and frequency have significant influences on the process parameters and can improve the surface accuracy and microstructure uniformity of thin-wall parts.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Physical

Macro/micro-structure and mechanical properties of Al-6Mg-0.3Sc alloy fabricated by oscillating laser-arc hybrid additive manufacturing

Shengchong Ma et al.

Summary: In this study, an oscillating laser-arc hybrid additive manufacturing (O-LHAM) process was developed to fabricate thin-wall parts of Al-6Mg-0.3Sc alloy. Compared to wire and arc additive manufacturing (WAAM), O-LHAM showed reduced surface roughness, increased effective wall width, mitigated porosity, and refined and homogenized microstructures, resulting in improved mechanical properties of the material.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Periodic microstructure of Al-Mg alloy fabricated by inter-layer hammering hybrid wire arc additive manufacturing: Formation mechanism, microstructural and mechanical characterization

Siyu Zhou et al.

Summary: Inter-layer plastic deformation is an effective method to improve the mechanical properties of wire arc additive manufacturing (WAAM) components. In this study, a periodic microstructure composed of alternate coarse and fine grain regions was obtained by applying the inter-layer hammering hybrid WAAM process. The grain size and dislocation density in the recrystallization region were significantly refined, leading to improved tensile properties. The best results were achieved when the inter-layer region was hammered 3 times.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Engineering, Industrial

Synchronous-hammer-forging-assisted laser directed energy deposition additive manufacturing of high-performance 316L samples

Dongjiang Wu et al.

Summary: The synchronous-hammer-forging-assisted laser directed energy deposition (SHLDED) method has been developed to regulate the microstructure and mechanical properties of 316L stainless steel samples. The results demonstrate that SHLDED samples show refined grains and enhanced mechanical properties compared to the commonly used LDED samples.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Wire and arc additive manufacturing of dissimilar 2319 and 5B06 aluminum alloys

Tianxing Chang et al.

Summary: By combining different types of aluminum alloys, their functional properties can be expanded. Based on the research results, the mechanical properties of components composed of dissimilar alloys fabricated by WAAM can be effectively improved through proper control of microstructure and internal defects.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Sc Content on the Microstructure and Properties of Al-Mg-Sc Alloys Deposited by Wire Arc Additive Manufacturing

Lingling Ren et al.

Summary: In this study, Al-Mg-Sc alloy deposits with different Sc contents were prepared by a WAAM process. It was found that at a Sc content of 0.3%, the alloy exhibited the best mechanical properties, making it suitable for applications in aviation and aerospace.

METALS AND MATERIALS INTERNATIONAL (2021)

Add to Collection

Article Engineering, Industrial

Metal transfer modes for Wire Arc Additive Manufacturing Al-Mg alloys: Influence of heat input in microstructure and porosity

E. Aldalur et al.

Summary: WAAM technology is used to manufacture medium-to-large metallic parts using aluminum alloys, with aluminum alloy 5356 being analyzed in this study. Three working modes for aluminum alloys are compared, with pulsed-AC mode showing significantly reduced porosity levels and being a very attractive mode for this aluminum alloy.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Study of microstructural and mechanical anisotropy of 7075 Al deposits fabricated by cold spray additive manufacturing

Yupeng Ren et al.

Summary: This work explores the microstructural and mechanical anisotropy in cold spray additively manufactured 7075 Al deposits. The study reveals a strong anisotropy in the deposits, with ultimate tensile strength gradually decreasing as the tensile direction changes. Crack propagation behavior shows uniformity in the XY plane but significant anisotropy in planes perpendicular to the XY plane.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of β-phase precipitates in an aluminum-magnesium alloy at the nanoscale

Daniel L. Foley et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Engineering, Manufacturing

High-performance integrated additive manufacturing with laser shock peening -induced microstructural evolution and improvement in mechanical properties of Ti6Al4V alloy components

Jinzhong Lu et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution and stress state related to mechanical properties of electron beam melted Ti-6Al-4V alloy modified by laser shock peening

Liang Lan et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure evolution of wire-arc additively manufactured 2319 aluminum alloy with interlayer hammering

Xuewei Fang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Engineering, Industrial

Microstructure and properties of Al alloy ER5183 deposited by variable polarity cold metal transfer

Bowen Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of titanium powder on microstructure and mechanical properties of wire plus arc additively manufactured Al-Mg alloy

Liwei Wang et al.

MATERIALS LETTERS (2019)

Add to Collection

Article Chemistry, Physical

Effect of heat input on microstructure and mechanical properties of Al-Mg alloys fabricated by WAAM

Chuanchu Su et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Engineering, Industrial

Workpiece vibration augmented wire arc additive manufacturing of high strength aluminum alloy

Chen Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Engineering, Industrial

Additive manufacturing using WAAM with AA5183 wire

A. Horgar et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Deformation microstructures and strengthening mechanisms for the wire plus arc additively manufactured Al-Mg4.5Mn alloy with inter-layer rolling

Jianglong Gu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Optics

Melt flow and grain refining in ultrasonic vibration assisted laser welding process of AZ31B magnesium alloy

Lei Zhenglong et al.

OPTICS AND LASER TECHNOLOGY (2018)

Add to Collection

Review Engineering, Manufacturing

A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement

Bintao Wu et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Article Chemistry, Physical

Correlations between Microstructure Characteristics and Mechanical Properties in 5183 Aluminium Alloy Fabricated by Wire-Arc Additive Manufacturing with Different Arc Modes

Xuewei Fang et al.

MATERIALS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Application of bulk deformation methods for microstructural and material property improvement and residual stress and distortion control in additively manufactured components

Paul A. Colegrove et al.

SCRIPTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

An improved prediction of residual stresses and distortion in additive manufacturing

T. Mukherjee et al.

COMPUTATIONAL MATERIALS SCIENCE (2017)

Add to Collection

Article Engineering, Manufacturing

Improvement in Geometrical Accuracy and Mechanical Property for Arc-Based Additive Manufacturing Using Metamorphic Rolling Mechanism

Yang Xie et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2016)

Add to Collection

Article Engineering, Industrial

The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys

Jianglong Gu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

The effectiveness of combining rolling deformation with Wire-Arc Additive Manufacture on β-grain refinement and texture modification in Ti-6Al-4V

J. Donoghue et al.

MATERIALS CHARACTERIZATION (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Wire plus Arc Additive Manufacturing

S. W. Williams et al.

MATERIALS SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Chemistry, Physical

Effect of Mn and Fe on the Formation of Fe- and Mn-Rich Intermetallics in Al-5Mg-Mn Alloys Solidified Under Near-Rapid Cooling

Yulin Liu et al.

MATERIALS (2016)

Add to Collection

Article Engineering, Industrial

Microstructure and residual stress improvement in wire and arc additively manufactured parts through high-pressure rolling

Paul A. Colegrove et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Hydrogen-induced gas porosity formation in Al-4.5 wt% Cu-1.4 wt% Mg alloy

Prince N. Anyalebechi

JOURNAL OF MATERIALS SCIENCE (2013)

Add to Collection

Article Engineering, Mechanical

Hybrid direct manufacturing method of metallic parts using deposition and micro continuous rolling

Haiou Zhang et al.

RAPID PROTOTYPING JOURNAL (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Four-Dimensional Annihilation Behaviors of Micro Pores during Surface Cold Working

Hiroyulci Toda et al.

MATERIALS TRANSACTIONS (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Healing behavior of preexisting hydrogen micropores in aluminum alloys during plastic deformation

H. Toda et al.

ACTA MATERIALIA (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of casting imperfections on the fatigue life of 319-F and A356-T6 Al-Si casting alloys

H. R. Ammar et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of microporosity on tensile properties of A356 aluminum alloy

Choong Do Lee

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of composition, Sr modification, and annealing treatment on the structure and properties of cast Al-4 pct Mg alloys

FH Samuel et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2003)

Add to Collection

Article Engineering, Manufacturing

Rapid prototyping of 5356-aluminum alloy based on variable polarity gas tungsten arc welding: Process control and microstructure

JH Ouyang et al.

MATERIALS AND MANUFACTURING PROCESSES (2002)

Add to Collection

Article Engineering, Manufacturing

Rapid prototyping based on variable polarity gas tungsten arc welding for a 5356 aluminium alloy

H Wang et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.