☆ 4.6 Article

Effect of a Large Height-to-Diameter Ratio Upsetting-Extrusion Process on the Microstructure and Mechanical Properties of Mg-Gd-Y-Zn-Zr Alloys

JOM (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Effect of a new upsetting process with large height-to-diameter ratio on the microstructure of Mg-Gd-Y-Zn-Zr alloy

Yugang Ye et al.

Summary: A new upsetting process with a large height-to-diameter ratio is proposed to overcome the limitation of the traditional process. The study successfully upset a Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy bar with a height-to-diameter ratio of 6.5 and investigated its microstructure evolution. Dynamic recrystallization occurred during the process, resulting in significant microstructure refinement, with a maximum recrystallization ratio of 46.3% and an average grain size of 20.2 μm in the center of the billet.

MATERIALS LETTERS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution and mechanical properties of cup-shaped specimens prepared by rotary backward extrusion

Chao Liu et al.

Summary: Rotary backward extrusion (RBE) was used to prepare large cup-shaped specimens, and the effects of rotary speed on microstructure and properties were analyzed. The results showed that the microstructure became finer from the outer to inner region, and increasing the rotary speed improved deformation uniformity and mechanical properties. Continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) actively contributed to hot deformation. Refinement strengthening was the major mechanism during RBE, and the highest recrystallization reached 93.1%.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Add to Collection

Article Chemistry, Physical

Preparation of ultra-high strength Mg-Gd-Y-Zn-Zr alloy by pre-ageing treatment prior to extrusion

Jie Zheng et al.

Summary: The pre-ageing treatment significantly improved the mechanical properties and fracture behavior of the extruded Mg-Gd-Y-Zn-Zr alloy by promoting dynamic recrystallization and achieving a more homogeneous microstructure. The pre-aged-extruded sample showed excellent strength-ductility synergy, with increased yield strength, ultimate tensile strength, and elongation compared to the solution-extruded sample.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Nanocrystallization of the cast AZ31 Mg alloy by low-strain rotary swaging

Xin Chen et al.

Summary: Remarkable grain refinement of AZ31 Mg alloy was achieved by low-strain rotary swaging, with nanograins formed in the central region attributed to high strain rates and constantly changing loading directions. The nanocrystallization process in the central region was dominated by tension twinning and the formation of dislocation arrays, while only twins were formed in the edge region due to a single loading direction towards the center.

MATERIALS LETTERS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Formation of an abnormal texture in Mg-Gd-Y-Zn-Mn alloy and its effect on mechanical properties by altering extrusion parameters

Kui Wang et al.

Summary: The microstructure, texture, and mechanical properties of Mg-8Gd-4Y-1Zn-Mn alloys extruded with different extrusion ratios and subsequent cooling processes were investigated. Increasing extrusion ratio promoted dynamic recrystallization, while subsequent water cooling suppressed static recrystallization. The strength differences in the alloy were mainly due to fiber strengthening along different directions.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of heat treatment on microstructure evolution and mechanical properties of selective laser melted Mg-11Gd-2Zn-0.4Zr alloy

Qingchen Deng et al.

Summary: The study found that through optimized post heat treatment, the microstructure of SLMed GZ112K alloys can be significantly improved, increasing their ductility and yield strength. Additionally, after peak aging heat treatment, SLM-T6 GZ112K alloys exhibit higher mechanical properties.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Strengthening of low-cost rare earth magnesium alloy Mg-7Gd-2Y-1Zn-0.5Zr through multi-directional forging

Qinghe Wei et al.

Summary: This study investigates the effects of multidirectional forging (MDF) on a low-cost rare earth magnesium alloy, revealing that the Mg-7Gd-2Y-1Zn-0.5Zr alloy shows increased strength and elongation after undergoing extrusion, MDF, and T5 treatment. The alloy strength enhancement is attributed to solid solution strengthening, grain refinement, and aging precipitation mechanisms. Additionally, the dynamic recrystallization mechanism shifts from discontinuous to continuous during MDF at reduced temperatures, impacting deformation behavior.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

EFFECT OF COOLING RATE ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF SOLUTION-TREATED Mg-9Gd-4Y-2Zn-0.5Zr ALLOY

Zixuan Wang et al.

Summary: The cooling rate has an effect on the microstructure and mechanical properties of Mg-9Gd-4Y-2Zn-0.5Zr alloy, with higher cooling rates resulting in smaller grain sizes and the LPSO phase filling the entire matrix grains. The furnace-cooled samples have better yield strength but poorer ultimate tensile strength and elongation to failure.

MATERIALI IN TEHNOLOGIJE (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of heat treatment on mechanical properties and microstructure evolution of Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy

Jie Zheng et al.

Summary: This article discusses the effects of heat treatment on the properties of the as-cast Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy at room temperature, as well as the mechanical properties and microstructure evolution of various peak-aging samples at different tensile temperatures. The optimal heat treatment process for the alloy is determined to be 520°C x 24 h + 200°C x 112 h. The strength initially increases and then decreases as the tensile temperature increases, while the ductility monotonously increases.

JOURNAL OF MAGNESIUM AND ALLOYS (2022)

Add to Collection

Article Chemistry, Physical

Effect of heterogeneous microstructure on the mechanical properties and deformation behavior of rotating backward extruded ZK61 alloy

Jie Zheng et al.

Summary: Rotating backward extrusion (RBE), as a novel severe plastic deformation process, shows promising industrial application prospects. The microstructural evolution and mechanical properties of ZK61 Mg alloy tubular components prepared by RBE process in different regions were investigated. It was found that samples with preferentially microstructural compositions (volume fraction of fine grains: 40-60%) exhibited better work hardening capability and strong-toughness synergy.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Annealing Before Aging on Microstructure and Mechanical Properties of Mg-Gd-Y-Zn-Zr Alloy

Chao Liu et al.

Summary: In this study, the elongation of Mg-9Gd-4Y-2Zn-0.5Zr alloy after aging was improved by introducing annealing treatment. Static recrystallization occurred during annealing process, resulting in refined microstructure. After annealing, the sample reached the maximum elongation, which was 7.4%.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Crystallography

Nanoindentation on the Transformation of LPSO Phases during Different Solution Heat Treatments in an Mg-Dy-Nd-Zn-Zr Alloy

Petra Maier et al.

Summary: This study investigates the nanomechanical properties of extruded and heat-treated Mg-Dy-Nd-Zn-Zr, with a focus on the transformation of long-period stacking-ordered (LPSO) phases using nanoindentation. The results show that the quantity and hardness of the LPSO phases undergo different changes during annealing. The grain size also changes with the formation of LPSO lamellae.

CRYSTALS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Quasi-in-situ observing the rare earth texture evolution in an extruded Mg-Zn-Gd alloy with bimodal microstructure

M. G. Jiang et al.

Summary: This study investigated the static recrystallization and texture evolution in an extruded Mg-Zn-Gd alloy, providing direct evidence of rare earth (RE) texture evolution during grain growth. The research findings contribute to understanding the mechanisms involved in forming RE texture during extrusion and developing wrought Mg alloys with improved formability.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Toward the development of Mg alloys with simultaneously improved strength and ductility by refining grain size via the deformation process

Zhi Zhang et al.

Summary: Grain size significantly influences the strength and ductility of magnesium alloys, and refining grain size is a feasible strategy to prepare high-performance magnesium alloys. Further research and discussion on the effects of grain size on various magnesium alloys are needed to fully understand the key mechanisms.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

The microstructure evolution, texture weakening mechanism and mechanical properties of AZ80 Mg alloy processed by repetitive upsetting-extrusion with reduced deformation temperature

Xi Zhao et al.

Summary: The repetitive upsetting-extrusion (RUE) method is utilized to improve the strength and toughness of AZ80 Mg rods while reducing tensile anisotropy. The resulting microstructure after RUE processing shows a refinement of grains and dynamic recrystallization, leading to enhancements in mechanical properties. The introduction of an interactive stress state promotes dispersion of fiber texture and contributes to the elimination of tensile yield anisotropy in extruded bars.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

An alternating ageing-annealing process for enhancing strength and ductility of a Mg-Gd-Y-Zn-Zr alloy

Jie Zheng et al.

Summary: The proposed alternating ageing-annealing process resulted in a homogeneous microstructure with short rod-shaped LPSO phases and beta ' phases in the Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy, leading to an excellent strength-ductility synergistic effect. The mechanical properties of the alloy were significantly improved, with a yield strength of 425 MPa, an ultimate tensile strength of 493.2 MPa, and an elongation of 11.2% after heat treatment.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Inhomogeneous microstructure and mechanical anisotropy of multi-directional forged Mg-Gd-Y-Zn-Ag-Zr alloy

Cen Huang et al.

Summary: In this study, a bulky Mg-Gd-Y-Zn-Ag-Zr alloy was prepared through multi-directional forging under specific conditions. The microstructure, texture, and mechanical properties of different regions were analyzed, showing significant grain refinement but also inhomogeneous microstructures and mechanical anisotropy. The optimum mechanical properties were found in the center region, indicating the complexity of the relationship between microstructure and mechanical performance in the alloy bulk.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The microstructure and mechanical properties of Mg-Gd-Y-Zn-Zr system and Mg-Gd-Y-Zr system alloys by RUE deformation

Leichen Jia et al.

Summary: This study investigates the effects of long-period stacking order (LPSO) phases on the dynamic recrystallization (DRX) process in Mg-Gd-Y-Zn-Zr (GWZ) alloy and Mg-Gd-Y-Zr (GW) alloy, and finds that GWZ alloy exhibits better grain refinement and texture strength compared to GW alloy, while its tensile strength is higher but elongation is lower.

MATERIALS RESEARCH EXPRESS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

On the microstructure and RE-texture evolution during hot tensile deformation of Mg-Gd-Y-Zn-Zr alloy

Mozhgan Shokri et al.

Summary: The study investigated the correlation between microstructure/texture evolutions and high temperature flow behavior in Mg alloy containing long period stacking order (LPSO) phases. The annealing treatment effectively strengthened the alloy and decreased ductility, with blocky LPSO assisting dynamic recrystallization and lamellar LPSO increasing alloy strength. The findings suggest that microstructure and texture evolution play a significant role in the high-temperature behavior of the Mg alloy.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of forced-air cooling on the microstructure and age-hardening response of extruded Mg-Gd-Y-Zn-Zr alloy full with LPSO lamella

S. Z. Wu et al.

Summary: This study investigates the effect of forced-air cooling on the microstructure and age-hardening response of a Mg-8.2Gd-3.8Y-1.0Zn-0.4 Zr alloy with plate-shaped LPSO phases. Results show that forced-air cooling restricts dynamic recrystallization, promotes dynamic precipitation, and enhances the overall mechanical properties of the alloy.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

Microstructure and texture evolution of Mg-RE-Zn alloy prepared by repetitive upsetting-extrusion under different decreasing temperature degrees

Guanshi Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

A novel severe plastic deformation method and its effect on microstructure, texture and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Zhaoming Yan et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

Formation mechanism of the abnormal texture during extrusion in Mg-Y-Sm-Zn-Zr alloy

Shaoyuan Lyu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

The evolution of long-period stacking ordered phase and its effect on dynamic recrystallization in Mg-Gd-Y-Zn-Zr alloy processed by repetitive upsetting-extrusion

Yingze Meng et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Chemistry, Physical

The Role of Long Period Stacking Ordered Phase in Dynamic Recrystallization of a Mg-Gd-Y-Zn-Zr Alloy during Multi-Directional Forging Process

Huiling Liu et al.

MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Bulk nanocrystalline high-strength magnesium alloys prepared via rotary swaging

Yingchun Wan et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

The role of long-period stacking ordered phases in the deformation behavior of a strong textured Mg-Zn-Gd-Y-Zr alloy sheet processed by hot extrusion

Tao Chen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Chemistry, Physical

Achievement of fine-grained bimodal microstructures and superior mechanical properties in a multi-axially forged GWZ magnesium alloy containing LPSO structures

S. M. Ramezani et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Chemistry, Physical

Effects of repetitive upsetting-extrusion parameters on microstructure and texture evolution of Mg-Gd-Y-Zn-Zr alloy

Guanshi Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy during equal channel angular pressing

Bing Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Recrystallization and mechanical properties of WE43 magnesium alloy processed via cyclic expansion extrusion

Soheil Amani et al.

INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Exceptional grain refinement in a Mg alloy during high pressure torsion due to rare earth containing nanosized precipitates

W. T. Sun et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Texture evolution, deformation mechanism and mechanical properties of the hot rolled Mg-Gd-Y-Zn-Zr alloy containing LPSO phase

Jianbo Shao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of homogenization treatment on microstructure and elongation of the Mg-13Gd-4Y-2Zn-0.6Zr alloy

Shi Wenjia et al.

MATERIALS RESEARCH EXPRESS (2018)

Add to Collection

Article Chemistry, Physical

Effect of Isothermal Repetitive Upsetting Extrusion on the Microstructure of Mg-12.0Gd-4.5Y-2.0Zn-0.4Zr Alloy

Guanshi Zhang et al.

MATERIALS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Preparation, Microstructure Evolutions, and Mechanical Property of an Ultra-Fine Grained Mg-10Gd-4Y-1.5Zn-0.5Zr Alloy

Huan Liu et al.

METALS (2017)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Mechanical properties of Mg-8Gd-3Y-0.5Zr alloy with bimodal grain size distributions

J. H. He et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

The role of metastable LPSO building block clusters in phase transformations of an Mg-Y-Zn alloy

Jin-Kyung Kim et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Development of extraordinary high-strength Mg-8Al-0.5Zn alloy via a low temperature and slow speed extrusion

Hui Yu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Chemistry, Physical

Effect of ageing treatment on the precipitation behaviour of Mg-Gd-Y-Zn-Zr alloy

C. Xu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

Add to Collection

Article Chemistry, Physical

Effect of solid solution and aging treatments on the microstructures evolution and mechanical properties of Mg-14Gd-3Y-1.8Zn-0.5Zr alloy

Song Zhang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

Add to Collection

© Peeref 2019-2024. All rights reserved.