☆ 4.6 Article

Finite Element Analysis of Additively Manufactured Continuous Carbon Fiber-Reinforced Composites

JOM (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Composites

On flexural properties of additive manufactured composites: Experimental, and numerical study

David Krzikalla et al.

Summary: This study focused on experimental and numerical examination of the flexural properties of FDM long carbon fibre reinforced composites with polymeric matrix of Onyx through 3-point bending test. The reinforced layer distribution was found to be crucial over the fibre content, with comparable longitudinal material constants but dissimilar shear and transversal constants.

COMPOSITES SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Article Polymer Science

Experimental Characterization and Modeling of 3D Printed Continuous Carbon Fibers Composites with Different Fiber Orientation Produced by FFF Process

Federico Lupone et al.

Summary: This study investigates the microstructure and mechanical properties of 3D printed CCF/PA composites with different layups and applies predictive models. It found that longitudinal composites have the highest stiffness and strength, while cross-ply and quasi-isotropic laminates have lower properties. The reduction in tensile properties for these laminates can be described using the Angle Minus Longitudinal. The rupture mode of quasi-isotropic laminates mainly exhibits debonding between beads.

POLYMERS (2022)

Add to Collection

Article Materials Science, Composites

Multi-scale analysis for 3D printed continuous fiber reinforced thermoplastic composites

Yutong Fu et al.

Summary: The research explores the designing and fabrication of continuous fiber reinforced thermoplastic composites through additive manufacturing technology. It simulates the manufacturing process and mechanical properties, providing insights for the design and evaluation of 3D printed CFRTPCs. The study offers a theoretical basis and simulation method for predicting the mechanical properties of 3D printed CFRTPCs.

COMPOSITES SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Engineering, Multidisciplinary

Numerical modelling of the elastic properties of 3D-printed specimens of thermoplastic matrix reinforced with continuous fibres

E. Polyzos et al.

Summary: Numerical modelling of 3D-printed Fused Filament Fabrication (FFF) specimens with thermoplastic matrices reinforced with continuous fibres, focusing on the elastic properties, revealed good correlation with analytical models for the micro- and meso-scale and with experimental data for the macro-scale, indicating validity and efficiency of the developed approach.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Article Automation & Control Systems

Effect of the fiber orientation on the tensile and flexural behavior of continuous carbon fiber composites made via fused filament fabrication

Alberto Parmiggiani et al.

Summary: This study aims to analyze the mechanical resistance of components made with continuous carbon fiber (CCF) thermoplastic materials using fused filament fabrication (FFF), with a focus on the influence of fiber orientation. Tensile and bending characteristics are evaluated according to test standards, comparing experimental findings with reference specimens to understand the advantages or limitations of different fiber arrangements.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Longitudinal compression failure of 3D printed continuous carbon fiber reinforced composites: An experimental and computational study

Haibin Tang et al.

Summary: The study systematically investigates the longitudinal compression failure mechanisms of 3D printed continuous carbon fiber reinforced polymer components using the Fused Filament Fabrication (FFF) technique. Experimental and computational analyses show that the introduction of waved filaments can lead to degradation of the failure strength, although further degradation is limited when more waved filaments are used. Fracture morphology analysis reveals the occurrence of in-plane and out-of-plane kink-bands, with failure predominantly at the cross-section with the contact region of the waved and regular filaments.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2021)

Add to Collection

Article Engineering, Multidisciplinary

Additive manufacturing of polymeric composites from material processing to structural design

Shangqin Yuan et al.

Summary: This review discusses the advantages of polymeric composites with multi-functionality over metals and the intensive attention that additive manufactured composites have received over the past decade. The focus is on the design and manufacturing methods for polymeric composites using additive manufacturing, including different types of reinforcements and designs for multi-functional applications.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Article Materials Science, Composites

Drivers of mechanical performance variance in 3D-printed fused filament fabrication parts: An Onyx FR case study

Christine Ma et al.

Summary: The study found that moisture and print orientation were the main factors affecting the mechanical properties in a 3D printing system. User-controlled factors had a significant impact on tensile strength, while user-uncontrolled factors had a minor effect. Reinforcing the part with continuous fiber significantly reduced moisture-induced variance and increased measured strength.

POLYMER COMPOSITES (2021)

Add to Collection

Article Materials Science, Characterization & Testing

A finite element approach for the prediction of the mechanical behaviour of layered composites produced by Continuous Filament Fabrication (CFF)

Manuela Galati et al.

Summary: Continuous Filament Fabrication (CFF) is an additive manufacturing process that produces components with long fiber reinforced materials without the need for tools or molds. A preliminary study using 3D Finite Element (FE) method was conducted to predict the mechanical behavior of composites fabricated by CFF. The study developed a FE model to determine material properties and validated the model through experimental and numerical comparisons.

POLYMER TESTING (2021)

Add to Collection

Review Mechanics

A critical review on 3D printed continuous fiber-reinforced composites: History, mechanism, materials and properties

S. M. Fijul Kabir et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Review Engineering, Manufacturing

Additively manufactured carbon fiber-reinforced composites: State of the art and perspective

Nekoda van de Werken et al.

ADDITIVE MANUFACTURING (2020)

Add to Collection

Article Mechanics

Design and 3D printing of continuous fiber reinforced heterogeneous composites

Zhanghao Hou et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Engineering, Manufacturing

Overview of 3D additive manufacturing (AM) and corresponding AM composites

Yuxuan Wang et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)

Add to Collection

Article Materials Science, Composites

Flexural properties of symmetric carbon and glass fibre reinforced hybrid composite laminates

Chensong Dong

COMPOSITES PART C: OPEN ACCESS (2020)

Add to Collection

Article Materials Science, Composites

Additive manufacturing of continuous fibre reinforced thermoplastic composites using fused deposition modelling: Effect of process parameters on mechanical properties

J. M. Chacon et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Review Engineering, Mechanical

A review on fibre reinforced composite printing via FFF

Isaac Ferreira et al.

RAPID PROTOTYPING JOURNAL (2019)

Add to Collection

Article Engineering, Manufacturing

An investigation into 3D printing of fibre reinforced thermoplastic composites

L. G. Blok et al.

ADDITIVE MANUFACTURING (2018)

Add to Collection

Article Engineering, Multidisciplinary

Uncertainties in flexural strength of carbon/glass fibre reinforced hybrid epoxy composites

Chensong Dong

COMPOSITES PART B-ENGINEERING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Process-Induced Voids on the Properties of Fibre Reinforced Composites

Chensong Dong

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

Add to Collection

Article Engineering, Multidisciplinary

Flexural properties of hybrid composites reinforced by S-2 glass and T700S carbon fibres

Chensong Dong et al.

COMPOSITES PART B-ENGINEERING (2012)

Add to Collection

Article Mechanics

Review of Degradation Models for Progressive Failure Analysis of Fiber Reinforced Polymer Composites

Mark R. Garnich et al.

Applied Mechanics Reviews (2008)

Add to Collection

© Peeref 2019-2024. All rights reserved.