☆ 4.7 Article

Dynamic shear behavior of forged CrMnFeCoNi high entropy alloy using hat-shaped specimens over a wide range of temperatures and strain rates

INTERNATIONAL JOURNAL OF PLASTICITY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Rapid amorphization of CrMnFeCoNi high-entropy alloy under ultrasonic vibrations

Caitao Fan et al.

Summary: Due to their unique design concept, high-entropy alloys (HEAs) exhibit unusual properties and lead to an emerging new field. In this study, it is shown that a typical face-centered cubic crystalline phase CoCrFeNiMn HEA can be easily transformed into the amorphous phase through ultrasonic vibration treatment at a frequency of 20000 Hz. Nanoscale hierarchical features, including twins, stacking faults bands, hexagonal-close packed phase bands, and amorphous bands, can be clearly observed in samples treated with different ultrasonic vibration energies. The main mechanism of ultrasonic vibration-induced amorphization is the promotion of amorphous phase formation through grain refinement when the defect density at grain boundaries reaches a critical level. Furthermore, mechanical instability is easily induced by ultrasonic vibration at high strain rate to generate amorphous phase inside grains. As a result of ultrasonic vibration treatment, the HEA samples exhibit significant improvement in mechanical performance, mainly attributed to microstructure evolution, especially the generation of the amorphous phase, such as yielding strength and hardness. This rapid amorphization process not only provides a potential strengthening mechanism for HEAs but also offers a novel approach to investigate the crystal-amorphous transition problem.

MATERIALS & DESIGN (2023)

Add to Collection

Article Engineering, Mechanical

Shear localization in polycrystalline metal at high-strain rates with dynREamic recrystallization: Crystal plasticity modeling and texture effect

Wen An et al.

Summary: Shear localization in metals at high-strain rates is a significant failure mode, and predicting its occurrence and evolution accurately is a great challenge. A new dislocation-based crystal plasticity constitutive model with dynamic recrystallization as a crucial mechanism of shear instability was developed. The model was validated through numerical prediction and experimental data, showing that dynamic recrystallization can be a dominant mechanism for shear instability. The study also investigated the effects of loading mode and texture on shear localization in Cu-Al alloys. This work is important for understanding microstructural evolution in shear localization formation and designing microstructures to control or prevent shear localization.

INTERNATIONAL JOURNAL OF PLASTICITY (2023)

Add to Collection

Article Engineering, Mechanical

Adiabatic shear localization induced by dynamic recrystallization in an FCC high entropy alloy

Kun Jiang et al.

Summary: In this study, the dynamic mechanical behavior of a face-centered cubic (FCC) high/medium entropy alloy (HEA) was investigated through split Hopkinson pressure bar (SHPB) experiments. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) were used to examine the microstructure of the specimens. The results showed that the alloy exhibited strong strain hardening capacity, strain rate sensitivity, and temperature dependence. The compressive failure at 77 K was caused by crack propagation within adiabatic shear bands (ASBs), which were formed due to dynamic recrystallization (DRX) of the material. The severe local shear flow, adiabatic temperature rise, and fast quenching within the ASBs resulted in ultrafine grains.

INTERNATIONAL JOURNAL OF PLASTICITY (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of temperature and strain rate on quasi-static and dynamic compressive behavior of forged CrMnFeCoNi high entropy alloy

Jie Sun et al.

Summary: The mechanical properties of CrMnFeCoNi HEA can be improved by forging, with increased compressive strength and plasticity. After forging, CrMnFeCoNi still maintains its face-centered cubic structure, with reduced grain size, more uniform elemental distribution, and the introduction of some defects. Compression tests at different temperatures and strain rates show that the material exhibits excellent compressive strength and great plasticity, with high sensitivity to temperature and strain rate. Different types of dynamic recrystallization, including DDRX, CDRX, and TDRX, are activated during hot compressions, with the formation of deformed twins favored at low temperature and high strain rate.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Quantitative investigation on deformation mechanism and dynamic recrystallization during localized adiabatic shearing of single crystal copper

Jianlin He et al.

Summary: In this study, the adiabatic shearing of single crystals was achieved by using large-sized columnar crystalline pure copper specimens prepared by directional solidification and a hat-shaped sample design. The flow stress was found to increase with increasing strain rate, and the dominant deformation mechanism at high strain rates was slipping rather than twinning. The microstructure of the sheared zone showed the transformation from large-sized dislocation cells to elongated dislocation cells and the occurrence of equiaxed recrystallized grains. This instantaneous grain refinement was attributed to the dynamic recrystallization of pure copper under adiabatic shearing conditions.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Add to Collection

Article Nanoscience & Nanotechnology

Shear deformation of pure-Cu and Cu/Nb nano-laminates using micromechanical testing

Tanvi Ajantiwalay et al.

Summary: Solid phase processing with shear deformation can lead to unique microstructure evolution and improved mechanical properties in immiscible systems like Cu/Nb. To understand the correlation between microstructure and deformation behavior, localized simple-shear loading is applied using a specialized S-shaped specimen geometry in pure-Cu and Cu/Nb accumulative roll-bonded nanolaminates. The nanoscale microstructure and proximity of interfaces in Cu/Nb result in a 2.8-fold increase in shear stress compared to pure-Cu. The adapted geometry successfully captures shear deformation at predicted sites in both material systems and could be a powerful technique for studying deformation mechanisms.

SCRIPTA MATERIALIA (2023)

Add to Collection

Article Engineering, Mechanical

New insights into the role of porous microstructure on dynamic shear localization

A. R. Vishnu et al.

Summary: This paper presents new insights into the role of porous microstructure on dynamic shear localization. Finite element calculations of electromagnetically collapsing thick-walled cylinders were performed, and the numerical simulations showed that voids promote dynamic shear localization and affect the nucleation and development of shear bands.

INTERNATIONAL JOURNAL OF PLASTICITY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic deformation behavior of a FeCrNi medium entropy alloy

Ao Fu et al.

Summary: FeCrNi medium entropy alloy prepared by powder metallurgy method exhibits high strain-hardening ability and multiple deformation mechanisms. Analysis of shear localization behavior reveals distinct microstructural characteristics inside and outside the shear band, with microvoids preferentially nucleating in the central area and eventually leading to shear band fracture with increasing strain.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

1.45 GPa ultrastrong cryogenic strength with superior impact toughness in the in-situ nano oxide reinforced CrMnFeCoNi high-entropy alloy matrix nanocomposite manufactured by laser powder b e d fusion

Young-Kyun Kim et al.

Summary: The study introduced a new method for developing high-performance CrMnFeCoNi HEAs at cryogenic temperatures by utilizing additive manufacturing and the addition of interstitial atoms. The HEA nanocomposite fabricated using laser powder bed fusion exhibited superior mechanical properties, with excellent yield strengths, tensile strengths, and Charpy impact energies at both room temperature and cryogenic temperature.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Forced shear deformation behaviors of annealed pure titanium under quasi-static and dynamic loading

Zhicheng Zhu et al.

Summary: The mechanical behavior and microstructure characteristics of pure titanium with hat-shaped specimens under quasi-static and dynamic loading were investigated and compared. The study found that dynamic specimens exhibited higher yield stress and peak stress compared to quasi-static specimens. Microstructure characterization revealed different localized deformation mechanisms in the two types of specimens, with quasi-static specimens showing a wide shear localization region mainly composed of elongated twin structures, while dynamic specimens exhibited an ASB region consisting of ultrafine equiaxed grains resulting from rotational dynamic recrystallization. The study also observed different types of primary twins and multiple generations of twins in both types of specimens. The microhardness of the shear localization region in quasi-static specimens and the ASB region in dynamic specimens were found to be higher due to strain hardening and ultrafine-grained strengthening, respectively. Microtexture analysis revealed different orientation relationships between grains and local shear planes in the two types of specimens.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Pure mode II dynamic fracture characteristics and failure mechanism of Zr41.2Ti13.8Cu12.5Ni10Be22.5 bulk metallic glass

Yang Han et al.

Summary: This study presents a novel experimental technique to determine the dynamic fracture toughness of bulk metallic glasses at high loading rates. The results show that the loading rate does not significantly affect the fracture toughness, but decreases the fracture initiation time. The fracture surface exhibits different regions with distinct failure modes and micromechanisms.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Review Materials Science, Multidisciplinary

The effects of irradiation on CrMnFeCoNi high-entropy alloy and its derivatives

Zhouran Zhang et al.

Summary: High-entropy alloys (HEAs) have potential for intriguing combinations of mechanical and other properties, with focus on irradiation response such as high phase stability and resistance to radiation-induced segregation. The Cantor alloy and its derivatives exhibit encouraging irradiation resistance superior to traditional dilute alloys, showing smaller size but higher number density of dislocation loops, significantly lower extent of swelling and improved resistance to He bubble growth. Future research directions for irradiation resistant HEAs are suggested.

PROGRESS IN MATERIALS SCIENCE (2022)

Add to Collection

Article Materials Science, Coatings & Films

Revealing the deformation mechanisms of the heterogeneous structured CrMnFeCoNi high entropy alloy with ameliorated mechanical and corrosion resistance properties

Yun Zou et al.

Summary: This study successfully introduced a gradient structure with grain size variation into the CrMnFeCoNi HEA using ultrasonic nanocrystal surface modification. The heterogeneous structured CrMnFeCoNi HEA exhibited excellent combination properties of strength and ductility. The deformation and strengthening mechanisms were investigated, and it was found that the corrosion resistance properties were also improved. The UNSM process improved the comprehensive mechanical and corrosion resistance properties of CrMnFeCoNi HEA.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

High temperature tensile properties of as-cast and forged CrMnFeCoNi high entropy alloy

Jie Sun et al.

Summary: This paper investigates the high temperature tensile properties of a single-phase FCC high entropy alloy and reveals that hot forging can refine the grain size and improve the tensile strength. The alloy exhibits different mechanical behaviors and fracture modes at different temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Mechanical behavior of high-entropy alloys

Weidong Li et al.

Summary: Research in high-entropy alloys has been booming since the 2010s, focusing on the vast potential in compositions, microstructures, and properties. Efforts are mainly directed towards exploring the compositional space and microstructures, as well as understanding the mechanical behavior. However, there is still a lack of comprehensive studies on the mechanical behavior of high-entropy alloys.

PROGRESS IN MATERIALS SCIENCE (2021)

Add to Collection

Article Engineering, Mechanical

Dynamic behavior of CrMnFeCoNi high-entropy alloy in impact tension

Yu Qiao et al.

Summary: This paper reveals the unusual simultaneous strength-plasticity enhancement and high strain rate embrittlement inhibition of CrMnFeCoNi HEA in impact tension through split Hopkinson tensile bar (SHTB) testing and high-speed photography. Microstructural analysis shows that the cooperation of twins and dislocations is the crucial mechanism for the synchronous enhancement of strength-plasticity in this alloy under impact tension. A thermo-viscoplastic constitutive model based on dislocations and twins evolution was developed to describe the dynamic mechanical behavior of HEAs at high strain rates.

INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2021)

Add to Collection

Article Chemistry, Physical

Improved mechanical and corrosion properties of CrMnFeCoNi high entropy alloy with cold rolling and post deformation annealing process

Yun Zou et al.

Summary: The CR-PDA process can significantly refine the grain size of high entropy alloys, increase hardness and strength, but decrease ductility, while also improving corrosion resistance. The main strengthening mechanisms are fine grain and dislocation density strengthening.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Engineering, Mechanical

The modified GTN-Thomason criterion for modelling of ductile fracture considering shear factor and size effect in micro-scaled plastic deformation

W. T. Li et al.

Summary: Coarse grains result in fewer voids on fracture surfaces and higher flow strength, while finer grains accelerate the occurrence of shear-dominated fracture and hinder normal tensile fracture. By introducing shear factor and size effect, the modified GTN-Thomason criterion predicts ductile fracture in micro-scaled plastic deformation and enhances understanding and prediction of ductile fracture.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure, texture, and fracture of pure magnesium adiabatic shear band under high strain rate compression

Shiyuan Zhou et al.

Summary: The study reveals that under dynamic shear loading, a straight ASB is formed in pure magnesium specimens, consisting of transition and central regions with equiaxed grains containing large angle grain boundaries. Grain and strain increase from ASB central to matrix regions, resulting in strain concentration in the matrix region. The mechanically-driven subgrain rotation model explains the texture in ASB, showing dynamic recrystallized grains slip and rotate under normal stress, leading to a mixed fracture mode of brittle and ductile fracture along the ASB.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Multidisciplinary Sciences

Amorphization in extreme deformation of the CrMnFeCoNi high-entropy alloy

Shiteng Zhao et al.

Summary: High-entropy alloys (HEAs) show remarkable material properties under harsh conditions, with structures containing stacking faults, twins, transformation between crystal structures, and amorphization being generated through plastic deformation processes.

SCIENCE ADVANCES (2021)

Add to Collection

Article Engineering, Mechanical

Simultaneous enhancement of strength and ductility in a NiCoCrFe high-entropy alloy upon dynamic tension: Micromechanism and constitutive modeling

T. W. Zhang et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Engineering, Mechanical

Quasi-static and dynamic response, and texture evolution of two overaged Al 7056 alloy plates in T761 and T721 tempers: Experiments and modeling

Angela Y. Ku et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic failure of titanium: Temperature rise and adiabatic shear band formation

Yazhou Guo et al.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Shear deformation behavior of Zircaloy-4 alloy plate

Fusen Yuan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Engineering, Mechanical

Planar slip-driven fatigue crack initiation and propagation in an equiatomic CrMnFeCoNi high-entropy alloy

Kai Suzuki et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Micro-compression studies of face-centered cubic and body-centered cubic high-entropy alloys: Size-dependent strength, strain rate sensitivity, and activation volumes

Yuan Xiao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural characteristics and formation mechanism of adiabatic shear bands in Al-Zn-Mg-Cu alloy under dynamic shear loading

Weiliang Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Strain rate dependent shear localization and deformation mechanisms in the CrMnFeCoNi high-entropy alloy with various microstructures

Zhengling Yang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Discovery and design of fatigue-resistant high-entropy alloys

Weidong Li et al.

SCRIPTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Simultaneous twinning and microband formation under dynamic compression in a high entropy alloy with a complex energetic landscape

D. L. Foley et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Engineering, Mechanical

Strain localization and dynamic recrystallization in polycrystalline metals: Thermodynamic theory and simulation framework

Charles K. C. Lieou et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of impurities on adiabatic shear bands (ASB) formation and evolution in U-2.5 wt%Nb alloy under impact

Dawu Xiao et al.

JOURNAL OF NUCLEAR MATERIALS (2019)

Add to Collection

Article Engineering, Mechanical

Simultaneously enhancing strength and ductility of a high-entropy alloy via gradient hierarchical microstructures

M. N. Hasan et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Study on the microstructural characteristics of adiabatic shear band in solid-solution treated ZK60 magnesium alloy

Yang Yang et al.

MATERIALS CHARACTERIZATION (2019)

Add to Collection

Article Physics, Multidisciplinary

Temperature Rise Associated with Adiabatic Shear Band: Causality Clarified

Yazhou Guo et al.

PHYSICAL REVIEW LETTERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Adiabatic shear localization in the CrMnFeCoNi high-entropy alloy

Zezhou Li et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Dynamic shear deformation of a CrCoNi medium-entropy alloy with heterogeneous grain structures

Yan Ma et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical and microstructural properties of 2024-T351 aluminium using a hat-shaped specimen at high strain rates

Nathan J. Edwards et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

High-strain-rate plastic deformation and fracture behaviour of Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy at room temperature

Chun Ran et al.

MECHANICS OF MATERIALS (2018)

Add to Collection

Article Multidisciplinary Sciences

Dynamic deformation behavior of a face-centered cubic FeCoNiCrMn high-entropy alloy

Junyang He et al.

SCIENCE BULLETIN (2018)

Add to Collection

Article Engineering, Mechanical

Dynamic recrystallization in adiabatic shear banding: Effective-temperature model and comparison to experiments in ultrafine-grained titanium

Charles K. C. Lieou et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Shear localization and recrystallization in high strain rate deformation in Ti-5Al-5Mo-5V-1Cr-1Fe alloy

Chun Ran et al.

MATERIALS LETTERS (2018)

Add to Collection

Review Construction & Building Technology

A review on split Hopkinson bar experiments on the dynamic characterisation of concrete

Mohammad Reza Khosravani et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

The dependence of the Taylor-Quinney coefficient on the dynamic loading mode

D. Rittel et al.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Dynamic shear deformation and failure of Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy

Chun Ran et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Multidisciplinary Sciences

High-velocity deformation of Al0.3CoCrFeNi high-entropy alloy: Remarkable resistance to shear failure

Z. Li et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Spherical nanoindentation creep behavior of nanocrystalline and coarse-grained CoCrFeMnNi high-entropy alloys

Dong-Hyun Lee et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Engineering, Mechanical

A deformation mechanism based crystal plasticity model of ultrafine-grained/nanocrystalline FCC polycrystals

Akhtar S. Khan et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2016)

Add to Collection

Article Chemistry, Physical

Plastic deformation behavior of a thermo-mechanically processed AZ31 magnesium alloy under a wide range of temperature and strain rate

Farhoud Kabirian et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Shock compression response of high entropy alloys

Z. J. Jiang et al.

MATERIALS RESEARCH LETTERS (2016)

Add to Collection

Article Engineering, Mechanical

Mechanical responses and deformation mechanisms of an AZ31 Mg alloy sheet under dynamic and simple shear deformations

Amit Pandey et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2015)

Add to Collection

Article Engineering, Mechanical

Strain rate effect of high purity aluminum single crystals: Experiments and simulations

Akhtar S. Khan et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Adiabatic shear localization in pure titanium deformed by dynamic loading: Microstructure and microtexture characteristic

Yanghui Jiang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Editorial Material Materials Science, Multidisciplinary

High entropy alloys

H. K. D. H. Bhadeshia

MATERIALS SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Adiabatic Shear Banding and Cracking Phenomena Occurring During Cold-Forging Simulation Tests of Plain Carbon Steel Wire Rods by Using a Split Hopkinson's Pressure Bar

Minju Kang et al.

METALS AND MATERIALS INTERNATIONAL (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of microstructure on the nucleation and initiation of adiabatic shear bands (ASBs) during impact

Solomon Boakye Yiadom et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Measurement of stored energy in Fe-48%Ni alloys strongly cold-rolled using three approaches: Neutron diffraction, Dillamore and KAM approaches

Yanick Ateba Betanda et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Multidisciplinary Sciences

A fracture-resistant high-entropy alloy for cryogenic applications

Bernd Gludovatz et al.

SCIENCE (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Molecular dynamics study of the α-γ phase transition in Fe induced by shear deformation

Binjun Wang et al.

ACTA MATERIALIA (2013)

Add to Collection

Article Engineering, Mechanical

Microstructural examination of quasi-static and dynamic shear in high-purity iron

E. K. Cerreta et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2013)

Add to Collection

Article Engineering, Mechanical

Modeling periodic adiabatic shear band evolution during high speed machining Ti-6Al-4V alloy

G. G. Ye et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2013)

Add to Collection

Article Engineering, Mechanical

Experimental and numerical investigations of yield surface, texture, and deformation mechanisms in AA5754 over low to high temperatures and strain rates

Amit Pandey et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2013)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Formation condition of solid solution type high-entropy alloy

Ming-xing Ren et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Thermo-mechanical aspects of adiabatic shear failure of AM50 and Ti6Al4V alloys

D. Rittel et al.

MECHANICS OF MATERIALS (2008)

Add to Collection

Article Physics, Multidisciplinary

Dynamic Recrystallization as a Potential Cause for Adiabatic Shear Failure

D. Rittel et al.

PHYSICAL REVIEW LETTERS (2008)

Add to Collection

Article Physics, Multidisciplinary

Adiabatic shear failure and dynamic stored energy of cold work

D Rittel et al.

PHYSICAL REVIEW LETTERS (2006)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural development in equiatomic multicomponent alloys

B Cantor et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)

Add to Collection

Article Engineering, Mechanical

Adiabatic shear banding in high speed machining of Ti-6Al-4V: experiments and modeling

A Molinari et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.