☆ 4.7 Article

Long-term ageing effect on mechanical properties of polyamide 12 printed by Multi-Jet-Fusion

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

Machine learning predicts fretting and fatigue key mechanical properties

Maysam B. Gorji et al.

Summary: This study uses machine learning to predict fretting crack lengths and corresponding stress intensity factors under partial slip conditions. The finite element analysis was used to compute the fretting SIF threshold for each arrested crack condition. A neural network model was developed to describe fretting crack lengths and SIF based on experimental parameters, showing promising results for accurate predictions.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Article Engineering, Mechanical

Machine learning assisted investigation of defect influence on the mechanical properties of additively manufactured architected materials

Erhai Hu et al.

Summary: This study investigates the impact of defect features on the mechanical properties of truss lattices in additive manufacturing. Surface roughness exceeding 10% reduces the specific modulus and strength, while interior voids affect different geometries differently.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Article Engineering, Mechanical

Deep learning based phase transformation model for the prediction of microstructure and mechanical properties of hot-stamped parts

Yongfeng Li et al.

Summary: Hot stamping of boron steel is effective for weight reduction in automobile parts, but the loss of mechanical properties due to incomplete martensitic transformation is a challenge. In this study, a deep-learning based phase transformation model is developed to capture the history-dependent phase transformation behavior of boron steel under hot stamping conditions. The model integrates diffusive and diffusionless transformation and provides a novel approach for two-scale simulation of hot stamping process.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Article Engineering, Mechanical

Determination of ductile fracture properties of 16MND5 steels under varying constraint levels using machine learning methods

Xingyue Sun et al.

Summary: The current paper presents a machine learning method based on artificial neural network (ANN) model for the determination of ductile fracture properties of 16MND5 bainitic forging steel with various three-dimensional (3D) constraint conditions. The proposed training strategy, which includes an artificially divided training set and the introduction of dropout layer, effectively reduces the training data and prevents overfitting. The ANN model shows good prediction performance and can be helpful in solving ductile fracture properties of different geometric dimensions in harsh environments.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Article Engineering, Mechanical

A physics-informed multi-agents model to predict thermo-oxidative/hydrolytic aging of elastomers

Aref Ghaderi et al.

Summary: This paper presents a novel physics-informed multi-agents constitutive model for predicting the quasi-static constitutive behavior of cross-linked elastomers and the mechanical performance loss during environmental aging. The model, based on a data-driven machine learning engine, captures damages in the polymer matrix and changes in material behavior. It also simplifies the high-dimensional mapping problem into multiple 1D problems through a sequential order reduction method.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2022)

Add to Collection

Article Engineering, Manufacturing

Effects of build positions on the thermal history, crystallization, and mechanical properties or polyamide 12 parts printed by Multi Jet Fusion

Kaijuan Chen et al.

Summary: This study investigates the effects of build positions on the thermal history, crystallization, and mechanical properties of MJF PA12 parts. It is found that parts printed in the centre region experience slower cooling rate, resulting in larger crystallite size and crystallinity. However, these parts also have slightly higher tensile modulus and significantly smaller elongation at break and strain energy density compared to parts printed at the boundaries.

VIRTUAL AND PHYSICAL PROTOTYPING (2022)

Add to Collection

Article Polymer Science

Influence of Atmospheric Conditions on Mechanical Properties of Polyamide with Different Content of Recycled Material in Selective Laser Sintering

Ana Pilipovic et al.

Summary: The price of material is an important factor when selecting the additive polymer procedure. In selective laser sintering (SLS), the price can be reduced by recycling material and optimizing orientation. The product also needs to withstand the influences of UV radiation and humidity. The test results show that exposure to UV radiation reduces tensile elongation, but has the opposite effect on flexural deformation.

POLYMERS (2022)

Add to Collection

Article Energy & Fuels

Use of Machine Learning and Data Analytics to Detect Downhole Abnormalities While Drilling Horizontal Wells, With Real Case Study

Ahmed Alsaihati et al.

Summary: Standard torque and drag modeling programs are widely used in the oil and gas industry, but face accuracy issues, requiring adjustments to match actual conditions. This study aims to develop an intelligent system to predict surface drilling torque, detect operational problems ahead of time, and extend response time limits.

JOURNAL OF ENERGY RESOURCES TECHNOLOGY-TRANSACTIONS OF THE ASME (2021)

Add to Collection

Article Engineering, Mechanical

Neural network-based prediction of the long-term time-dependent mechanical behavior of laminated composite plates with arbitrary hygrothermal effects

Sy-Ngoc Nguyen et al.

Summary: This study utilized RNN for accelerated prediction of the long-term deformation behavior of viscoelastic composite materials, simplifying the time-integrated constitutive relation and employing a smooth finite element method to reduce computational storage cost. The technique can be applied in real engineering structures under varying hygrothermal conditions.

JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

A multi-physics approach on modeling of hygrothermal aging and its effects on constitutive behavior of cross-linked polymers

Amir Bahrololoumi et al.

Summary: A multi-physics model is proposed to predict changes in the constitutive behavior of cross linked polymeric systems due to damages induced by deformation, oxidation, moisture, and temperature. The synergized effects of deformation-induced damage, as well as different environmental factors such as humidity, temperature, and oxygen, can be taken into account through a generic model. The study indicates that hygrothermal aging can be considered as a consequence of damage accumulation of two concurrent aging mechanisms, namely; (i) thermo-oxidative, and (ii) hydrolytic aging.

JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2021)

Add to Collection

Article Engineering, Mechanical

Modeling of humidity effect on electromechanical properties of viscoelastic dielectric elastomer

Junshi Zhang et al.

Summary: The research investigates the impact of humidity on the electromechanical performance of viscoelastic dielectric elastomers (DE) by analyzing the dependency relationships between various parameters and relative humidity. The study explores the influence of humidity on the static and dynamic electromechanical behaviors as well as stability and resonant frequency of the DE system.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Article Materials Science, Characterization & Testing

Mechanical properties and fracture characterization of additive manufacturing polyamide 12 after accelerated weathering

Tuomas Puttonen et al.

Summary: This study compared the mechanical properties of additive manufacturing and conventionally manufactured plastics after weathering, finding that PA12 and PA66 from additive manufacturing were significantly affected by weathering, while carbon reinforced PA12 showed the best aging resistance due to the UV varnish. Protective coatings can increase materials' weathering resistance, but also lead to an increase in the deviation of mechanical properties.

POLYMER TESTING (2021)

Add to Collection

Article Polymer Science

Comparative Characterization of Hot-Pressed Polyamide 11 and 12: Mechanical, Thermal and Durability Properties

Mohsen Bahrami et al.

Summary: Polyamide 11 (PA11) and polyamide 12 (PA12) have similar backbones but differ in origin, with PA11 being a bioplastic compared to oil-based PA12. This study characterizes and compares their properties, showing PA12's higher crystallinity leads to better mechanical and durability properties. Experimental results demonstrate the differences in ductility and water absorption between the two polyamides.

POLYMERS (2021)

Add to Collection

Article Engineering, Manufacturing

Relationships between porosity and mechanical properties of polyamide 12 parts produced using the laser sintering and multi-jet fusion powder bed fusion processes

Clinton Spencer Abbott et al.

Summary: The impact of residual porosity on the strength and ductility of polyamide-12 (PA-12) parts produced by powder bed fusion was evaluated in this study, comparing parts with and without hot isostatic pressure (HIP) treatment. It was found that part thickness significantly affects mechanical properties, and HIP treatment can reduce porosity, increase ultimate tensile strength, but may decrease maximum strains.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Mechanical

Experimental and modeling investigation on the viscoelastic-viscoplastic deformation of polyamide 12 printed by Multi Jet Fusion

Kaijuan Chen et al.

Summary: The study investigated the viscoelastic-viscoplastic deformation of MJF PA12, distinguishing between viscoelastic and viscoplastic deformations through experiments and numerical simulations. The influence of void defects on the deformation of PA12 was also explored. A constitutive model based on the logarithmic stress rate and stress localization was developed, with simulated results matching experimental findings and revealing the mechanism behind the low tensile ductility of MJF PA12.

INTERNATIONAL JOURNAL OF PLASTICITY (2021)

Add to Collection

Article Chemistry, Physical

Neural Network-Based Prediction Model to Investigate the Influence of Temperature and Moisture on Vibration Characteristics of Skew Laminated Composite Sandwich Plates

Vinayak Kallannavar et al.

Summary: This study developed a prediction model using artificial neural network to investigate the impact of temperature and moisture on the vibration response of skew laminated composite sandwich plates. The numerical results were used to train the ANN, and several numerical examples were presented to comprehend the influence of temperature and moisture on the LCS plates.

MATERIALS (2021)

Add to Collection

Article Engineering, Manufacturing

Additive manufacturing in COVID-19: recognising the challenges and driving for assurance

Hong Wei Tan et al.

Summary: The COVID-19 pandemic has highlighted the importance of additive manufacturing (AM) technology, showcasing its operational resilience and ability to provide rapid emergency responses. Collaborative efforts between the AM community, standards organisations, and regulatory authorities are needed to accelerate the progress of this technology. The lack of standards and regulations remains a primary challenge, but regulatory authorities and certification service providers are crucial in ensuring the safety and reliability of AM products.

VIRTUAL AND PHYSICAL PROTOTYPING (2021)

Add to Collection

Article Polymer Science

Plasticity-controlled failure of sintered and molded polyamide 12: Influence of temperature and water absorption

Fabio Paolucci et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2020)

Add to Collection

Article Automation & Control Systems

A comparative experimental study of additive manufacturing feasibility faced to injection molding process for polymeric parts

L. C. Paganin et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Life prediction for rate-dependent low-cycle fatigue of PA6 polymer considering ratchetting: Semi-empirical model and neural network based approach

Jingye Yang et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Engineering, Mechanical

Neural network model describing the temperature- and rate-dependent stress-strain response of polypropylene

Benoit Jordan et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Effect of Crystallinity on Water Vapor Sorption, Diffusion, and Permeation of PLA-Based Nanocomposites

Jon Trifol et al.

ACS OMEGA (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Material characterization of polyamide 12 and related agents used in the multi-jet fusion process: complementary application of high-resolution mass spectrometry and other advanced instrumental techniques

Beate Scherer et al.

MONATSHEFTE FUR CHEMIE (2020)

Add to Collection

Article Automation & Control Systems

On the difference in material structure and fatigue properties of polyamide specimens produced by fused filament fabrication and selective laser sintering

S. Terekhina et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Polymer Science

Physical Aging and Glass Transition of the Rigid Amorphous Fraction in Poly(L-lactic acid)

Xavier Monnier et al.

MACROMOLECULES (2020)

Add to Collection

Article Engineering, Manufacturing

Disclosing the build-up mechanisms of multi jet fusion: Experimental insight into the characteristics of starting materials and finished parts

Manuela Galati et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Construction & Building Technology

Engineering characteristics of nanosilica/polymer-modified bitumen and predicting their rheological properties using multilayer perceptron neural network model

Nur Izzi Md. Yusoff et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

Add to Collection

Article Engineering, Multidisciplinary

Comparison of physical and mechanical properties of PLA, ABS and nylon 6 fabricated using fused deposition modeling and injection molding

Makara Lay et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Engineering, Manufacturing

The process and performance comparison of polyamide 12 manufactured by multi jet fusion and selective laser sintering

Zhiyao Xu et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

Add to Collection

Article Mathematical & Computational Biology

Additive manufacturing of specific ankle-foot orthoses for persons after stroke: A preliminary study based on gait analysis data

Zhen Liu et al.

MATHEMATICAL BIOSCIENCES AND ENGINEERING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Ageing properties and polymer/fuel interactions of polyamide 12 exposed to (bio)diesel at high temperature

Xin-Feng Wei et al.

NPJ MATERIALS DEGRADATION (2019)

Add to Collection

Article Polymer Science

Comparison of long-term properties of laser sintered and injection molded polyamide 12 parts

Andreas Woerz et al.

JOURNAL OF POLYMER ENGINEERING (2018)

Add to Collection

Article Polymer Science

Effect of crystallinity on CF/PPS performance under weather exposure: Moisture, salt fog and UV radiation

Natassia L. Batista et al.

POLYMER DEGRADATION AND STABILITY (2018)

Add to Collection

Article Multidisciplinary Sciences

Phenomenological models for the isothermal physical aging of PEEK

Elida Beatriz Hermida et al.

HELIYON (2018)

Add to Collection

Article Polymer Science

The improvement of mechanical and thermal properties of polyamide 12 3D printed parts by fused deposition modelling

T. N. A. T. Rahim et al.

EXPRESS POLYMER LETTERS (2017)

Add to Collection

Article Engineering, Mechanical

Influence of environmental humidity and temperature on the creep behavior of sandwich panel

Zheng Chen et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)

Add to Collection

Article Polymer Science

Contribution of the rigid amorphous fraction to physical ageing of semi-crystalline PLLA

Maria Cristina Righetti et al.

POLYMER (2017)

Add to Collection

Article Construction & Building Technology

Study on the engineering properties and prediction models of an alkali-activated mortar material containing recycled waste glass

Chien-Chih Wang et al.

CONSTRUCTION AND BUILDING MATERIALS (2017)

Add to Collection

Article Polymer Science

Influence of the amorphous phase molecular mobility on impact and tensile properties of polyamide 6,6

Agustin Rios de Anda et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2016)

Add to Collection

Proceedings Paper Energy & Fuels

Role of crystallinity on moisture absorption and mechanical performance of recycled PET compounds

Takanori Negoro et al.

COE ON SUSTAINABLE ENERGY SYSTEM (THAI-JAPAN) (2016)

Add to Collection

Article Engineering, Chemical

Remaining useful life prediction of grinding mill liners using an artificial neural network

Farzaneh Ahmadzadeh et al.

MINERALS ENGINEERING (2013)

Add to Collection

Article Materials Science, Characterization & Testing

On the difference in material structure and fatigue properties of nylon specimens produced by injection molding and selective laser sintering

Brecht Van Hooreweder et al.

POLYMER TESTING (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of water conditioning on the fracture behavior of PA12 composites processed by selective laser sintering

Rocio Seltzer et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

Add to Collection

Article Engineering, Chemical

Degradation and Accelerated Ageing of Poly(Ether Block Amide) Thermoplastic Elastomers

D. Dixon et al.

POLYMER ENGINEERING AND SCIENCE (2011)

Add to Collection

Article Materials Science, Characterization & Testing

Effect of long-term ageing on the tensile properties of a polyamide 12 laser sintering material

R. D. Goodridge et al.

POLYMER TESTING (2010)

Add to Collection

Article Engineering, Mechanical

Degree of particle melt in Nylon-12 selective laser-sintered parts

Hadi Zarringhalam et al.

RAPID PROTOTYPING JOURNAL (2009)

Add to Collection

Article Polymer Science

Enthalpy relaxation and embrittlement of Poly(L-lactide) during physical aging

Pengju Pan et al.

MACROMOLECULES (2007)

Add to Collection

Article Environmental Sciences

Multiple regression models for the lower heating value of municipal solid waste in Taiwan

Y. F. Chang et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2007)

Add to Collection

Article Mechanics

Isothermal physical aging characterization of Polyether-ether-ketone (PEEK) and Polyphenylene sulfide (PPS) films by creep and stress relaxation

Yunlong Guo et al.

MECHANICS OF TIME-DEPENDENT MATERIALS (2007)

Add to Collection

Article Polymer Science

Crystalline structure of polyamide 12 as revealed by solid-state 13C NMR and synchrotron WAXS and SAXS

N Dencheva et al.

JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS (2005)

Add to Collection

Article Polymer Science

Creep and physical aging behaviour of PA6 nanocomposites

DPN Vlasveld et al.

POLYMER (2005)

Add to Collection

Article Polymer Science

Infrared spectroscopic study of the interactions of nylon-6 with water

R Iwamoto et al.

JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of water absorption on erosive wear behaviour of polyamides

JJ Rajesh et al.

JOURNAL OF MATERIALS SCIENCE (2002)

Add to Collection

Article Polymer Science

Glass transition and structural relaxation in semi-crystalline poly(ethylene terephthalate):: a DSC study

NM Alves et al.

POLYMER (2002)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of aging on glass transformation measurements by temperature modulated DSC

D Tonchev et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2002)

Add to Collection

Article Polymer Science

Study of the amorphous phase in semicrystalline poly(ethylene terephthalate) via physical aging

J Zhao et al.

MACROMOLECULES (2002)

Add to Collection

Article Polymer Science

Enthalpic relaxation in semi-crystalline PEEK

JR Atkinson et al.

POLYMER (2002)

Add to Collection

Article Polymer Science

Effects of physical aging on glass transition behavior of poly(DL-lactide)

KR Liao et al.

EUROPEAN POLYMER JOURNAL (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.