☆ 4.7 Article

Effect of pre-water immersion period on fatigue resistance of adhesive bonded thin steel

INTERNATIONAL JOURNAL OF FATIGUE (2023)

Related references

Note: Only part of the references are listed.

Article Polymer Science

The influence of interfacial failure on the tensile S-N response of aged Arcan joints

Joviano Antonio da Costa et al.

Summary: The study found that an increase in aging time leads to a decrease in the mechanical properties of adhesive joints, particularly in terms of fatigue strength and lifetime. Interfacial aging results in premature joint failure, with water diffusion rate significantly higher than that of the adhesive.

JOURNAL OF APPLIED POLYMER SCIENCE (2022)

Add to Collection

Review Metallurgy & Metallurgical Engineering

Effects of welding defects on the fatigue properties of spot welded automobile steel sheets and the establishment of a fatigue life evaluation method

Yuki Ogawa et al.

Summary: This study investigates the effect of simulated welding defect holes on the fatigue properties of spot welded joints, and establishes a unified evaluation method for the fatigue life of joints with different loading types.

WELDING IN THE WORLD (2022)

Add to Collection

Article Chemistry, Physical

A waste biomass-derived photothermic material with high salt-resistance for efficient solar evaporation

Heng-Shu Guan et al.

Summary: A low-cost, high-efficient solar evaporator derived from waste biomass was constructed with a Janus structure in this study, showing effective solar energy driven water evaporation for seawater desalination. The multifunctional photothermal sponge has a hydrophobic top layer and a hydrophilic bottom layer to prevent salt accumulation, ensuring high efficiency and stable water vapor output. The evaporator also exhibited excellent antibacterial property and potential for use in large-scale wastewater treatment and clean water generation.

CARBON (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of shot peening on static and fatigue properties of self-piercing riveting joints

Zhi-Chao Huang et al.

Summary: This study combines shot peening process with self-piercing riveting process to improve the performance of self-piercing riveting joints. Shot peening can induce residual compressive stress in aluminum sheets, resulting in improved static and fatigue strength of the joints. The main fatigue failure type is the damage of the lower sheets at the contact zones with the rivet leg. The shot peening process effectively enhances the self-piercing riveting joint performance.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Engineering, Mechanical

Effect of hygrothermal environment on the fatigue fracture mechanism of single lap Aluminum-CFRP hybrid (riveted/bonded) joints

Hanyu Zhang et al.

Summary: This paper investigates the influence of hygrothermal environment on the fatigue fracture mechanism of Aluminum-CFRP hybrid joints through experimental and simulation researches, and reveals the multi-stage fatigue failure characteristics and competitive mechanism of the joints.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Load-Bearing Capacities and Fracture Modes of Self-Piercing-Riveted, Adhesive-Bonded and Riv-Bonded Aluminum Joints at Quasi-Static and Cyclic Loadings

Josef Domitner et al.

Summary: The load-bearing capacities of adhesive-bonded and hybrid riv-bonded lap joints were superior to that of self-piercing-riveted joints under both static and cyclic loads. The joint quality/integrity played a crucial role in static and low-cycle fatigue failure, while the sheet properties mainly affected high-cycle fatigue failure.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical properties and fatigue failure mechanisms of purely self-piercing riveted (SPR) and hybrid (SPR-bonded) joints under salt spray environment

Zhi-Chao Huang et al.

Summary: Automotive light-weighting is an important trend in the automotive industry, and the joining of light-weighting materials is crucial. This study investigated self-piercing riveting (SPR) and SPR-bonded (SPR-A) joints of AA6061 and DP590 sheets, and evaluated their mechanical properties after exposure to salt spray environments for different aging times. The results showed that the shear and fatigue properties of the joints decreased with longer salt spray exposure. The SPR-A joints exhibited higher failure loads and energy absorption values compared to the SPR joints under the same salt spray time. Fatigue failure was mainly attributed to fretting wear between the rivet-foot and the lower sheet, and the salt spray time had no significant effect on the fatigue failure modes of both joint types.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Engineering, Civil

Degradation mechanism of steel/CFRP plate interface subjected to and

Junhui Li et al.

Summary: This study focused on the bond degradation mechanism of the steel/CFRP interface subjected to overloading fatigue damage and wetting/drying cycles, analyzing the role of interface cracks and microcracks in the degradation process, as well as the impact of moisture intrusion and chemical element changes on the interfacial bond strength.

THIN-WALLED STRUCTURES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of the mechanical performance of hybrid bolted-bonded joints subjected to different ageing conditions: Effect of geometrical parameters and bolt size

F. Delzendehrooy et al.

Summary: The hybrid bolted-bonded joining method is an effective way to mitigate concerns raised by the poor environmental resistance of adhesive joints in the marine industry. This study investigates the degradation of single lap hybrid bolted-bonded joints exposed to ageing conditions, and the results suggest that the size of the bolt and the ratios of hole diameter to width and hole diameter to edge distance have significant effects on the joint performance.

JOURNAL OF ADVANCED JOINING PROCESSES (2022)

Add to Collection

Article Engineering, Civil

Mechanical properties and corrosion behavior of galvanized steel/Al dissimilar joints

Hao Jiang et al.

Summary: This study compared the mechanical properties and corrosion behavior of different joints in a salt-spray environment. Results showed that single riveted joint had better corrosion resistance in the short term, while adhesive and hybrid joints were more affected by chloride ions, leading to reduced joint strength.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2021)

Add to Collection

Article Engineering, Chemical

Effect of hygrothermal and alternating load coupled aging on CFRP/Al bonded joints

Qianhui Xu et al.

Summary: The study investigated the effects of hygrothermal and alternating load coupled aging on CFRP/Al joint strength and failure modes. The research included artificial accelerated aging conditions with temperature cycle, high temperature and high humidity, and hygrothermal cycle. Results showed that aging time decreased joint strength due to degradation of the adhesive layer and damage to the adhesive/substrate interface. The worst influence on joint strength was observed in the hygrothermal cycle coupled with alternating load condition, followed by high temperature and high humidity coupled with alternating load, and the temperature cycle coupled with alternating load condition had the least influence on joint strength.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Interfacial Microstructure and Formation of Direct Laser Welded CFRP/Ti-6Al-4V Joint

Pengyuan Zou et al.

Summary: The combination of PEEK-CFRP with Ti-6Al-4V titanium alloy using continuous laser welding process is a promising manufacturing method, resulting in strong joints. However, the quality of joints is significantly affected by welding speed, with the formation of bubbles, cracks, and anchor effects impacting mechanical properties.

METALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Laser Patterning Preprocessing on Fatigue Strength of Adhesive Bonded Joints Using Thin Steel Plate

Katsuki Shikimoto et al.

MATERIALS TRANSACTIONS (2020)

Add to Collection

Article Construction & Building Technology

Behaviors of GFRP-steel bonded joints under cyclic loading after hygrothermal aging

Jie Liu et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

Add to Collection

Article Automation & Control Systems

Advances in joining technology of carbon fiber-reinforced thermoplastic composite materials and aluminum alloys

Bingchun Jiang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Multidisciplinary

Durability of adhesively bonded joints between pultruded GFRP adherends under hygrothermal and natural ageing

J. M. Sousa et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Engineering, Multidisciplinary

Influence of hydrothermal ageing on the mechanical properties of an adhesively bonded joint with different adherends

M. Mariam et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Engineering, Chemical

Effect of surface cold ablation on shear strength of CFRP adhesively bonded joint after UV laser treatment

Xiaohong Zhan et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2019)

Add to Collection

Proceedings Paper Engineering, Mechanical

Enhancements of a Stress-Based Approach for Fatigue Life Estimation of Multi-Material Connections Joined by Self-Piercing Rivets and Adhesive

Jan Presse et al.

FATIGUE DESIGN 2019, INTERNATIONAL CONFERENCE ON FATIGUE DESIGN, 8TH EDITION (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Fatigue degradation after salt spray ageing of electromagnetically riveted joints for CFRP/Al hybrid structure

Hao Jiang et al.

MATERIALS & DESIGN (2018)

Add to Collection

Article Engineering, Civil

Bond behavior of CFRP-steel double-lap joints exposed to marine atmosphere and fatigue loading

Qian-Qian Yu et al.

ENGINEERING STRUCTURES (2018)

Add to Collection

Article Materials Science, Coatings & Films

Effect of the Cold-Sprayed Aluminum Coating-Substrate Interface Morphology on Bond Strength for Aircraft Repair Application

Quentin Blochet et al.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2017)

Add to Collection

© Peeref 2019-2024. All rights reserved.