Related references
Note: Only part of the references are listed.Friction Stir Processing of Al-TiB2 In Situ Composite: Effect on Particle Distribution, Microstructure and Properties
Devinder Yadav et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2015)
Tungsten particle reinforced Al 5083 composite with high strength and ductility
Ranjit Bauri et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Influence of Stored Strain on Fabricating of Al/SiC Nanocomposite by Friction Stir Processing
M. Sarkari Khorrami et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)
Development of Cu particles and Cu core-shell particles reinforced Al composite
D. Yadav et al.
MATERIALS SCIENCE AND TECHNOLOGY (2015)
Mechanically activated effect of friction stir processing in Al-Ti reaction
Q. Zhang et al.
MATERIALS CHEMISTRY AND PHYSICS (2013)
Microstructures and mechanical properties of Al/Zn composites prepared by accumulative roll bonding and heat treatment
C. Y. Liu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Texture Produced by Abnormal Grain Growth in Friction Stir-Welded Aluminum Alloy 1050
Sergey Mironov et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
A New Route for Growing Large Grains in Metals
Eric M. Taleff et al.
SCIENCE (2013)
Abnormal Grain Growth Induced by Cyclic Heat Treatment
Toshihiro Omori et al.
SCIENCE (2013)
Processing of Intermetallic Titanium Aluminide Wires
Tom Marr et al.
METALS (2013)
Composite fabrication using friction stir processing-a review
H. S. Arora et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2012)
Exchange of experience the effect of synthesis time on the wear behavior of Al-8%Ti alloy produced by mechanical alloying
D. Ozyurek et al.
POWDER METALLURGY AND METAL CERAMICS (2012)
High strength Al-Al2O3p composites: Optimization of extrusion parameters
B. F. Luan et al.
MATERIALS & DESIGN (2011)
Processing, microstructure and mechanical properties of nickel particles embedded aluminium matrix composite
Devinder Yadav et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Ti-Al Composite Wires with High Specific Strength
Tom Marr et al.
METALS (2011)
Nickel particle embedded aluminium matrix composite with high ductility
Devinder Yadav et al.
MATERIALS LETTERS (2010)
Effect of extrusion and particle volume fraction on the mechanical properties of SiC reinforced Al-Cu alloy composites
Zhangwei Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Ultrafine equiaxed-grain Ti/Al composite produced by accumulative roll bonding
Dengke Yang et al.
SCRIPTA MATERIALIA (2010)
The kinetics of two-stage formation of TiAl3 in multilayered Ti/Al foils prepared by accumulative roll bonding
Dengke Yang et al.
INTERMETALLICS (2009)
Friction stir processing technology: A review
Z. Y. Ma
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)
Abnormal grain growth in friction stir processed alloys
I. Charit et al.
SCRIPTA MATERIALIA (2008)
Achieving ultrafine grain size in Mg-Al-Zn alloy by friction stir processing
C. I. Chang et al.
SCRIPTA MATERIALIA (2007)
Friction stir processed AA5182-O and AA6111-T4 aluminum alloys. Part 1: electron backscattered diffraction analysis
Sumit Agarwal et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2007)
Improving mechanical performance of Al by using Ti as reinforcement
Sanjay Kumar Thakur et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2007)
Growth of intermetallic layer in multi-laminated Ti/Al diffusion couples
L. Xu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Al-Al3Ti nanocomposites produced in situ by friction stir processing
C. J. Hsu et al.
ACTA MATERIALIA (2006)
Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31
Y. Morisada et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Reassessment of the binary aluminum-titanium phase diagram
Julius C. Schuster et al.
JOURNAL OF PHASE EQUILIBRIA AND DIFFUSION (2006)
Microstructure evolution during FSW/FSP of high strength aluminum alloys
JQ Su et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Friction stir welding and processing
RS Mishra et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2005)
Grain structure formation during friction stir welding observed by the 'stop action technique'
PB Prangnell et al.
ACTA MATERIALIA (2005)
Friction stir processing of large-area bulk UFG aluminum alloys
JQ Su et al.
SCRIPTA MATERIALIA (2005)
A new route to bulk nanocrystalline materials
JQ Su et al.
JOURNAL OF MATERIALS RESEARCH (2003)
Fine-grain evolution in friction-stir processed 7050 aluminum
CG Rhodes et al.
SCRIPTA MATERIALIA (2003)
Effect of clustering on the mechanical properties of SiC particulate-reinforced aluminum alloy 2024 metal matrix composites
SJ Hong et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Role of deformation twinning on strain hardening in cubic and hexagonal polycrystalline metals
SR Kalidindi et al.
ADVANCED ENGINEERING MATERIALS (2003)
Friction stir processing: a novel technique for fabrication of surface composite
RS Mishra et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Visualization of the material flow in AA2195 friction-stir welds using a marker insert technique
TU Seidel et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2001)
Reaction products of Al-Mg/B4C composite fabricated by pressureless infiltration technique
KB Lee et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)