☆ 4.5 Review

A Review on the Fundamental Properties of Sb2Se3-Based Thin Film Solar Cells

ENERGIES (2023)

Related references

Note: Only part of the references are listed.

Article Physics, Condensed Matter

Classification of lattice defects and the microscopic origin of p-type conductivity of Sb2Se3 solar cell absorber with varying Al2O3-layer thicknesses

Huafei Guo et al.

Summary: Based on first-principles calculations, this study reveals the origin of p-type conductivity and the roles of Al and O in enhancing hole concentration in Sb2Se3 thin films. A new class of low-energy defects with shallow acceptor levels is presented, while the concentration of holes induced by intrinsic and extrinsic defects is calculated and discussed. The findings provide an explanation for the experimental observation of increased hole concentration after Al2O3 capping and offer insights into the defect chemistry and physics of Sb2Se3 thin films. Additionally, the effects of Al2O3 layers with varying thicknesses on the crystallinity, orientation, and electrical properties of Sb2Se3 films are investigated. Finally, a solar cell efficiency of 6.87% is achieved without further optimization based on the FTO/CdS (CBD)/Sb2Se3/Al2O3/Au structure.

PHYSICA B-CONDENSED MATTER (2023)

Add to Collection

Article Physics, Multidisciplinary

Effect of thickness of antimony selenide film on its photoelectric properties and microstructure

Xin-Li Liu et al.

Summary: A combination of the Levenberg-Marquardt method and spectral fitting method (LM-SFM) is used to investigate the effects of film thickness on the refractive index (RI), absorption coefficient, optical band gap, Wemple-DiDomenico parameters, dielectric constant, and optical electronegativity of Sb2Se3 films. The results show that the RI and absorption coefficient of the films increase with thickness, while the optical band gap decreases. X-ray diffractometer (XRD), energy dispersive x-ray spectrometer (EDS), Mott-Davis state density model, and Raman microstructure analysis are used to explain the reasons behind the changes in the optical and electrical properties of the films.

CHINESE PHYSICS B (2023)

Add to Collection

Article Energy & Fuels

Innovative back-contact for Sb2Se3-based thin film solar cells

Stefano Pasini et al.

Summary: Among promising thin-film photovoltaic materials, Sb2Se3 (ASe) shows great potential due to its abundance of Earth elements and favorable optical and electrical properties. In this study, a Fe-S-O based back contact was proposed for ASe solar cells, which exhibited an ohmic contact and a contact resistivity of 0.8 Omega center dot cm(2). The performance of the solar cells remained stable after three months of testing.

SOLAR ENERGY (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Sb2Se3 Polycrystalline Thin Films Grown on Different Window Layers

Stefano Pasini et al.

Summary: Sb2Se3 is a V2VI3 binary chalcogenide compound with a single crystalline phase and fixed composition. It has a narrow energy gap (1.1 to 1.3 eV) that is optimal for single-junction solar cells. Due to its abundance and non-toxicity, Sb2Se3 is a promising material for low-cost thin-film solar cells. The preferential orientation of Sb2Se3 significantly affects the photovoltaic parameters, as demonstrated by Sb2Se3-based solar cells fabricated on different substrates.

COATINGS (2023)

Add to Collection

Article Energy & Fuels

Structural and optical properties of SbxSey thin films obtained by chemical molecular beam deposition method from Sb and Se precursors

T. M. Razykov et al.

Summary: SbxSey thin films were successfully obtained by chemical-molecular beam deposition (CMBD) on soda-lime glass with precise control of the Sb/Se ratio. The elemental and phase composition, crystal structure, and physical properties of these films with different compositions were investigated. The optical bandgap was determined from the absorption spectra acquired by spectrophotometer.

SOLAR ENERGY (2023)

Add to Collection

Article Chemistry, Applied

Back contact interfacial modification mechanism in highly-efficient antimony selenide thin-film solar cells

Junhui Lin et al.

Summary: In this study, the introduction of MoO2 as an intermediate layer in Sb2Se3 solar cells facilitated the growth of (211)-oriented Sb2Se3 with large grains, reduced contact resistance, minimized bulk and interfacial defects, and improved the power conversion efficiency of the solar cells.

JOURNAL OF ENERGY CHEMISTRY (2023)

Add to Collection

Article Chemistry, Multidisciplinary

Carrier Transport Enhancement Mechanism in Highly Efficient Antimony Selenide Thin-Film Solar Cell

Yandi Luo et al.

Summary: By introducing aluminum (Al3+) cation into the CdS buffer layer, this study improves the heterojunction interface of an Sb2Se3 solar cell. The energy band alignment of the Sb2Se3/CdS:Al heterojunction is modified from a cliff-like structure to a spike-like structure. As a result, the heterojunction interface engineering suppresses recombination losses and strengthens carrier transport, leading to a high efficiency of 8.41% for the substrate-structured Sb2Se3 solar cell. This study proposes a facile strategy for interfacial treatment and elucidates the related carrier transport enhancement mechanism, paving a bright avenue to overcome the efficiency bottleneck of Sb2Se3 thin-film solar cells.

ADVANCED FUNCTIONAL MATERIALS (2023)

Add to Collection

Article Energy & Fuels

Heterostructured CdS Buffer Layer for Sb2Se3 Thin Film Solar Cell

Al Amin et al.

Summary: The structural heterostructured CdS buffer layer can promote the vertical growth of Sb2Se3 nanoribbons, resulting in improved device efficiency of the solar cells. The improved buffer/absorber interface and reduced interface defects and recombination loss contribute to the efficiency enhancement. This new strategy provides a way to regulate the crystal growth of Sb2Se3 nanoribbons and further improve the efficiency of low-dimensional chalcogenide thin film solar cells.

SOLAR RRL (2023)

Add to Collection

Article Energy & Fuels

Zinc Chloride-Treated Indium Sulfide as Buffer Layer for Cd-Free Antimony Selenide Solar Cells

Yizhe Dong et al.

Summary: The posttreatment of In2S3 film with ZnCl2 solution serves as a buffer layer for constructing Sb2Se3 solar cells, improving the interfacial contact and suppressing carrier recombination. This strategy provides a facile and effective approach for using In2S3 as a buffer layer in inorganic chalcogenide solar cells.

SOLAR RRL (2023)

Add to Collection

Review Chemistry, Physical

Defect engineering in antimony selenide thin film solar cells

Udari Wijesinghe et al.

Summary: This article provides a comprehensive review of defect chemistry at surfaces, grain boundaries, and interfaces in Sb2Se3 solar cells, as well as efforts made to passivate these defect states in the community. Effective defect engineering is essential to enhance the performance and functionality of Sb2Se3 thin films, ultimately improving the efficiency and stability of solar cells.

ENERGY ADVANCES (2023)

Add to Collection

Article Chemistry, Multidisciplinary

Templated Growth and Passivation of Vertically Oriented Antimony Selenide Thin Films for High-Efficiency Solar Cells in Substrate Configuration

Suman Rijal et al.

Summary: A method to optimize the performance of Sb2Se3 thin-film solar cells by introducing a seed layer and post-treatment is introduced, resulting in the successful fabrication of Sb2Se3 planar heterojunction solar cells with high conversion efficiency.

ADVANCED FUNCTIONAL MATERIALS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Heterojunction Annealing Enabling Record Open-Circuit Voltage in Antimony Triselenide Solar Cells

Rong Tang et al.

Summary: This study reports an effective interface engineering approach using rapid thermal annealing to suppress nonradiative recombination near the Sb2Se3/CdS heterojunction, improving the performance of thin-film solar cells.

ADVANCED MATERIALS (2022)

Add to Collection

Article Energy & Fuels

Improvements in ultra-light and flexible epitaxial lift-off GaInP/GaAs/GaInAs solar cells for space applications

Jonas Schoen et al.

Summary: A thin, lightweight, flexible solar cell has been developed with optimized structure and using inverted metamorphic triple junction (IMM3J) technology and epitaxial lift-off (ELO) process. It maximizes the power-to-mass ratio under AM0 illumination and has competitive efficiency even after irradiation. The cell has shown high efficiency at different development stages and maintains a high conversion efficiency after irradiation.

PROGRESS IN PHOTOVOLTAICS (2022)

Add to Collection

Article Energy & Fuels

Solution-processed vanadium oxides as a hole-transport layer for Sb2Se3 thin-film solar cells

Al Amin et al.

Summary: In this study, inorganic vanadium oxides were utilized as a hole transport layer to enhance the efficiency and open-circuit voltage of antimony selenide solar cells. The use of VOx resulted in a significant increase in built-in voltage and improved device efficiency from 5.5% to 6.3%.

SOLAR ENERGY (2022)

Add to Collection

Article Energy & Fuels

Combating open circuit voltage loss in Sb2Se3 solar cell with an application of SnS as a back surface field layer

Vijay C. Karade et al.

Summary: In this study, a model of Sb2Se3 solar cell with SnS as a back surface field layer (BSF) was designed and analyzed via simulation. The introduction of the ultra-thin BSF layer significantly improved the open-circuit voltage and power conversion efficiency of the device.

SOLAR ENERGY (2022)

Add to Collection

Article Chemistry, Physical

Regulating Energy Band Alignment via Alkaline Metal Fluoride Assisted Solution Post-Treatment Enabling Sb2(S,Se)3 Solar Cells with 10.7% Efficiency

Yuqi Zhao et al.

Summary: By using a post-treatment technique, the quality of Sb-2(S,Se)(3) films was improved, leading to increased fill factor and short-circuit current density of solar cells, achieving a champion efficiency of 10.7%. This study provides an effective strategy for fabricating high-efficiency Sb-2(S,Se)(3) solar cells.

ADVANCED ENERGY MATERIALS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Crystal Growth Promotion and Defects Healing Enable Minimum Open-Circuit Voltage Deficit in Antimony Selenide Solar Cells

Guangxing Liang et al.

Summary: An effective absorber layer growth engineering is developed to grow high-quality Sb2Se3 films for thin-film solar cells. This engineering effort significantly improves the device efficiency by mitigating open-circuit voltage deficit, thanks to the repaired defects and improved charge transport.

ADVANCED SCIENCE (2022)

Add to Collection

Article Chemistry, Physical

Competing Superior Electronic Structure and Complex Defect Chemistry in Quasi-One-Dimensional Antimony Chalcogenide Photovoltaic Absorbers

Baiyu Zhang et al.

Summary: Antimony chalcogenides Sb2Se3 and Sb2S3 are emerging quasi-2D materials with great potential for low-cost and high-efficiency thin-film photovoltaics. However, their complex defect chemistry limits their photovoltaic performance, and efforts should be made to suppress the formation of detrimental native defects to improve their performance.

ACS APPLIED ENERGY MATERIALS (2022)

Add to Collection

Review Physics, Applied

The state of the art of Sb2(S, Se)3 thin film solar cells: current progress and future prospect

M. M. Nicolas-Marin et al.

Summary: This review focuses on the recent development of antimony sulfide selenide (Sb-2(S,Se)(3)) solar cells, discussing both experimental and theoretical results to understand the current limitations and potential improvements. The Sb-2(S,Se)(3) compound shows promise for single and multijunction solar cells, with a tunable band-gap ranging from 1.1 to 1.8 eV. Improved transport properties are observed when using SnO2:F as the substrate. The study also highlights the importance of addressing interface defects to improve the overall efficiency of the solar cells.

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2022)

Add to Collection

Article Engineering, Electrical & Electronic

Study of the optical properties of Sb2(Se1-xSx)3 (x=0-1) solid solutions

Mehmet Ender Uslu et al.

Summary: This study presents a detailed analysis of the optical properties of Sb-2(Se1-xSx)(3) polycrystals, which are promising semiconductor materials for optoelectronic applications. The successful formation of Sb-2(Se1-xSx)(3) solid solutions was confirmed and their electronic and defect structures were investigated using temperature and excitation power dependent photoluminescence (PL) analysis.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Enhanced Efficiency and Stability in Sb2S3 Seed Layer Buffered Sb2Se3 Solar Cells

Al Amin et al.

Summary: Antimony selenide (Sb2Se3) with quasi-1D nanoribbons structure shows excellent directional optical and electronic behaviors. The orientation of the nanoribbons is crucial for the photovoltaic performance of Sb2Se3 solar cells. This study develops a strategy for the vertical growth of Sb2Se3 nanoribbons by using an ultrathin layer of antimony sulfide (Sb2S3) to improve the overall efficiency of Sb2Se3 solar cells. The results show an increased efficiency from 5.65% to 7.44% through the improvement of all solar cell parameters.

ADVANCED MATERIALS INTERFACES (2022)

Add to Collection

Article Energy & Fuels

High-Resistance Metal Oxide Window Layers for Optimal Front Contact Interfaces in Sb2Se3 Solar Cells

Joao O. Mendes et al.

Summary: This study investigated the effect of high resistance metal oxide (HRMO) layers on the quality of the front contact in solar cells. The results showed that using ZnO or TiO2 HRMO layers between FTO substrates and CdS improves the overall device performance and stability.

SOLAR RRL (2022)

Add to Collection

Review Energy & Fuels

Ten Years of Sb2Se3 Thin Film Solar Cells

Chao Chen et al.

Summary: This article presents the major milestones in the development of antimony selenide thin film solar cells, including their selection and application, device structure, processing methods, orientation control, defect studies, and methods for defect passivation. The article also discusses the application of this technology in flexible devices and its future prospects.

SOLAR RRL (2022)

Add to Collection

Article Chemistry, Physical

Vapor Transport Deposition of Sb2(S,Se)3 Solar Cells with Continuously Tunable Band Gaps

Yanlin Pan et al.

Summary: Antimony chalcogenide (Sb-2(S,Se)(3)) films with continuously tunable band gaps were prepared through a vapor transport deposition process. By modifying the Se/S ratio in the evaporation source, the structural and optical properties of the films were successfully adjusted. An optimization of the band gap led to a power conversion efficiency of 7.1% for the Sb-2(S,Se)(3) single-junction solar cell.

ACS APPLIED ENERGY MATERIALS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Sb2Se3 Thin-Film Solar Cells Exceeding 10% Power Conversion Efficiency Enabled by Injection Vapor Deposition Technology

Zhaoteng Duan et al.

Summary: This study reports the fabrication of compact Sb2Se3 films using injection vapor deposition, resulting in high crystallinity and minimal defects, which leads to improved energy conversion efficiency in solar cells.

ADVANCED MATERIALS (2022)

Add to Collection

Article Energy & Fuels

Solar cell efficiency tables (Version 60)

Martin A. Green et al.

Summary: This article presents consolidated tables showing the highest independently confirmed efficiencies for solar cells and modules. The guidelines for including results in these tables are outlined, and new entries since January 2022 are reviewed. An appendix describing temporary electrical contacting methods and terminology for large-area solar cells is also included.

PROGRESS IN PHOTOVOLTAICS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Indirect Band Gap Semiconductors for Thin-Film Photovoltaics: High-Throughput Calculation of Phonon-Assisted Absorption

Jiban Kangsabanik et al.

Summary: The discovery of high-performance materials is an active field in photovoltaics research. This study proposes a computationally efficient method to screen potential thin-film PV absorbers by accounting for phonon-assisted absorption across the indirect band gap. Through screening descriptors, 28 candidate materials, including 20 indirect band gap semiconductors, were identified.

JOURNAL OF THE AMERICAN CHEMICAL SOCIETY (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Regulating deposition kinetics via a novel additive-assisted chemical bath deposition technology enables fabrication of 10.57%-efficiency Sb2Se3 solar cells

Yuqi Zhao et al.

Summary: By developing a novel additive-assisted chemical bath deposition (CBD) technology, researchers have successfully produced high-efficiency Sb2Se3 solar cells. The study reveals that the deposition process can be manipulated by additives to significantly enhance the physical properties of the films, resulting in a power conversion efficiency of 10.57%.

ENERGY & ENVIRONMENTAL SCIENCE (2022)

Add to Collection

Article Chemistry, Physical

Revealing the chemical structure-dependent carrier trapping in one-dimensional antimony selenide photovoltaic materials

Rui Cao et al.

Summary: This study compares the carrier dynamics of Sb2Se3 with anion-rich and cation-rich characteristics, and finds that Se-rich Sb2Se3 can effectively suppress trap-assisted recombination and achieve higher photovoltaic energy conversion performance in solar cells.

JOURNAL OF MATERIALS CHEMISTRY A (2022)

Add to Collection

Article Chemistry, Physical

Sb2S3 solar cells with a cost-effective and dopant-free fluorene-based enamine as a hole transport material

Nimish Juneja et al.

Summary: The application of Sb2S3 solar cells is limited by their low power conversion efficiency and the use of expensive hole transport materials. By using V1236 as a novel HTM instead of P3HT, the efficiency and transparency of solar cells can be improved.

SUSTAINABLE ENERGY & FUELS (2022)

Add to Collection

Article Engineering, Electrical & Electronic

Theoretical investigation of the electronic structure and anisotropic optical properties of quasi-1D Sb2Se3photovoltaic absorber materials

Xuebing Peng et al.

Summary: Sb2Se3 is a nontoxic and environmentally friendly photovoltaic absorber material, with a narrow bandgap and high absorption coefficient. Theoretical studies using first-principles methods show that the quasi-one-dimensional structure of Sb2Se3 has an indirect bandgap of 0.953 eV and exhibits anisotropic characteristics in the dielectric function. The absorption coefficient is greater than 10(5) cm(-1).

JOURNAL OF COMPUTATIONAL ELECTRONICS (2021)

Add to Collection

Article Energy & Fuels

Optical properties of thin film Sb2Se3 and identification of its electronic losses in photovoltaic devices

Niva K. Jayswal et al.

Summary: Sb2Se3 is a promising absorber layer material for photovoltaic applications due to its attractive optical properties and rapid improvement in solar cell efficiency. The indirect bandgap and Urbach energy of Sb2Se3 are determined to be 1.12 eV and 21.1 meV, respectively. Spectroscopic techniques like photo-thermal deflection spectroscopy and spectroscopic ellipsometry are used to analyze various optical properties and simulate external quantum efficiency.

SOLAR ENERGY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Vapor Transport Deposition of Highly Efficient Sb2(S,Se)3 Solar Cells via Controllable Orientation Growth

Yanlin Pan et al.

Summary: The study presents a vapor transport deposition method to control the growth of large-grained dense Sb-2(S,Se)(3) films with good crystallization and preferred orientation. It highlights the importance of defect activation energy in determining the photovoltaic performance of Sb-2(S,Se)(3) and achieves a high power conversion efficiency of 8.17% by optimizing the absorber layer.

ADVANCED FUNCTIONAL MATERIALS (2021)

Add to Collection

Review Energy & Fuels

CdTe-Based Thin Film Solar Cells: Past, Present and Future

Alessandro Romeo et al.

Summary: CdTe solar cells, known for their robustness and stability, have become a leading thin film technology in the world. Over the past few decades, significant advancements have been made in improving the efficiency of CdTe solar cells. Future research may focus on alternative absorbers and addressing potential environmental impacts of this technology.

ENERGIES (2021)

Add to Collection

Article Energy & Fuels

Stable and efficient Sb2Se3 solar cells with solution-processed NiOx hole-transport layer

Liping Guo et al.

Summary: In this study, an n-i-p structure was fabricated for Sb2Se3 solar cells by integrating a solution-processed NiOx hole-transport layer to enhance carrier collection, resulting in an improved power conversion efficiency from 6.12% to 7.15% with a 50 nm NiOx HTL. The mechanism behind the enhanced device performance was characterized through material microstructure, device physics, and interface electronic behaviors, showing that the low-cost NiOx HTL can also improve device stability under accelerated stress tests.

SOLAR ENERGY (2021)

Add to Collection

Article Energy & Fuels

Analysis of grain orientation and defects in Sb2Se3 solar cells fabricated by close-spaced sublimation

R. Krautmann et al.

Summary: The performance of a superstrate TiO2/Sb2Se3 solar cell was improved by introducing a seed layer, resulting in columnar Sb2Se3 film growth and enhanced charge collection efficiency. Although measurements did not reveal strong preferred orientation, the growth of columnar Sb2Se3 along the [001] direction was observed to enhance texture. Temperature-dependent admittance spectroscopy and capacitance-voltage profiling showed deep defects in the Sb2Se3 absorber, indicating the need for post-deposition treatments to address defect density issues.

SOLAR ENERGY (2021)

Add to Collection

Review Chemistry, Physical

Overview of the Current State of Gallium Arsenide-Based Solar Cells

Nikola Pap et al.

Summary: GaAs-based solar cells, despite achieving the highest efficiency, are not widely used but are suitable for specific applications due to their durability. This review provides a summary of past, present, and future uses, as well as advancements in development and performance.

MATERIALS (2021)

Add to Collection

Article Energy & Fuels

As-Grown InGaAsN Subcells for Multijunction Solar Cells by Molecular Beam Epitaxy

Maxime Levillayer et al.

Summary: This article investigates the molecular beam epitaxy growth process of unannealed InGaAsN solar cells, focusing on the impact of growth temperature, As/III ratio, and the use of bismuth as a surfactant. Ex-situ characterization results indicate that a high As/III ratio ensures good optoelectronic properties and growth temperature influences the residual doping of the dilute nitride layer. The best InGaAsN solar cells achieved J(sc) and V-oc values of 7.94 mA/cm(2) and 0.375 V under specific conditions, with a potential generation of up to 12 mA/cm(2) in a multijunction solar cell.

IEEE JOURNAL OF PHOTOVOLTAICS (2021)

Add to Collection

Article Engineering, Environmental

An effective combination reaction involved with sputtered and selenized Sb precursors for efficient Sb2Se3 thin film solar cells

Yan-Di Luo et al.

CHEMICAL ENGINEERING JOURNAL (2020)

Add to Collection

Article Chemistry, Physical

Isotype Heterojunction Solar Cells Using n-Type Sb2Se3 Thin Films

Theodore D. C. Hobson et al.

CHEMISTRY OF MATERIALS (2020)

Add to Collection

Article Chemistry, Physical

Electronic Conduction Mechanisms and Defects in Polycrystalline Antimony Selenide

N. Cifuentes et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2020)

Add to Collection

Article Physics, Applied

Extrinsic dopants in quasi-one-dimensional photovoltaic semiconductor Sb2S3: A first-principles study

Zenghua Cai et al.

JOURNAL OF APPLIED PHYSICS (2020)

Add to Collection

Review Energy & Fuels

A review of Sb2Se3 photovoltaic absorber materials and thin-film solar cells

Abdurashid Mavlonov et al.

SOLAR ENERGY (2020)

Add to Collection

Article Energy & Fuels

Effects of substrate temperature and SnO2 high resistive layer on Sb2Se3 thin film solar cells prepared by pulsed laser deposition

Ke Yang et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2020)

Add to Collection

Article Chemistry, Physical

Efficiency improvement of flexible Sb2Se3 solar cells with non-toxic buffer layer via interface engineering

Chong Wang et al.

NANO ENERGY (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Controlled Sputtering Pressure on High-Quality Sb2Se3 Thin Film for Substrate Configurated Solar Cells

Rong Tang et al.

NANOMATERIALS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

The History of Photovoltaics with Emphasis on CdTe Solar Cells and Modules

Alessio Bosio et al.

COATINGS (2020)

Add to Collection

Article Energy & Fuels

Six-junction III-V solar cells with 47.1% conversion efficiency under 143 Suns concentration

John F. Geisz et al.

NATURE ENERGY (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Back Contact Interfacial Modification in Highly-Efficient All-Inorganic Planar n-i-p Sb2Se3 Solar Cells

Cong Liu et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Synergistic Effect through the Introduction of Inorganic Zinc Halides at the Interface of TiO2 and Sb2S3 for High-Performance Sb2S3 Planar Thin-Film Solar Cells

Jian Han et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

Add to Collection

Article Physics, Applied

In situ investigation of interfacial properties of Sb2Se3 heterojunctions

Shuaicheng Lu et al.

APPLIED PHYSICS LETTERS (2020)

Add to Collection

Article Physics, Applied

Defect properties of Sb2Se3 thin film solar cells and bulk crystals

Theodore D. C. Hobson et al.

APPLIED PHYSICS LETTERS (2020)

Add to Collection

Article Chemistry, Physical

Sputtered and selenized Sb2Se3 thin-film solar cells with open-circuit voltage exceeding 500 mV

Guang-Xing Liang et al.

NANO ENERGY (2020)

Add to Collection

Article Chemistry, Physical

Open-Circuit Voltage Loss of Antimony Chalcogenide Solar Cells: Status, Origin, and Possible Solutions

Chao Chen et al.

ACS ENERGY LETTERS (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Preparation and characterization of pulsed laser deposited CdSe window layer for Sb2Se3thin film solar cell

Yajun Yang et al.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Excitonic and electronic transitions in Me-Sb2Se3 structures

Nicolae N. Syrbu et al.

BEILSTEIN JOURNAL OF NANOTECHNOLOGY (2020)

Add to Collection

Review Energy & Fuels

Review of GIGS-based solar cells manufacturing by structural engineering

Nandang Mufti et al.

SOLAR ENERGY (2020)

Add to Collection

Article Energy & Fuels

Efficient Sb2Se3/CdS planar heterojunction solar cells in substrate configuration with (hk0) oriented Sb2Se3 thin films

Kunal J. Tiwari et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2020)

Add to Collection

Article Physics, Condensed Matter

Structural, morphological, compositional, optical and electrical properties of Sb2Se3 thin films deposited by pulsed laser deposition

Ke Yang et al.

SUPERLATTICES AND MICROSTRUCTURES (2020)

Add to Collection

Article Chemistry, Physical

Manipulating the Electrical Properties of Sb2(S,Se)3Film for High-Efficiency Solar Cell

Xiaomin Wang et al.

ADVANCED ENERGY MATERIALS (2020)

Add to Collection

Article Chemistry, Physical

Dual-function of CdCl2 treated SnO2 in Sb2Se3 solar cells

Jing Zhou et al.

APPLIED SURFACE SCIENCE (2020)

Add to Collection

Article Energy & Fuels

Role of the substrates in the ribbon orientation of Sb2Se3 films grown by Low-Temperature Pulsed Electron Deposition

F. Pattini et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2020)

Add to Collection

Article Chemistry, Physical

Natural Band Alignments and Band Offsets of Sb2Se3 Solar Cells

Huw Shiel et al.

ACS APPLIED ENERGY MATERIALS (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Aqueous solution processed MoS3 as an eco-friendly hole-transport layer for all-inorganic Sb2Se3 solar cells

Yuyuan Ma et al.

CHEMICAL COMMUNICATIONS (2020)

Add to Collection

Review Energy & Fuels

Progress and prospects for ultrathin solar cells

Ines Massiot et al.

NATURE ENERGY (2020)

Add to Collection

Article Energy & Fuels

Intrinsic Defect Limit to the Electrical Conductivity and a Two-Step p-Type Doping Strategy for Overcoming the Efficiency Bottleneck of Sb2S3-Based Solar Cells

Zenghua Cai et al.

SOLAR RRL (2020)

Add to Collection

Article Chemistry, Physical

Efficient defect passivation of Sb2Se3 film by tellurium doping for high performance solar cells

Yuyuan Ma et al.

JOURNAL OF MATERIALS CHEMISTRY A (2020)

Add to Collection

Article Chemistry, Physical

Deciphering the Role of Key Defects in Sb2Se3, a Promising Candidate for Chalcogenide-Based Solar Cells

Adrien Stoliaroff et al.

ACS APPLIED ENERGY MATERIALS (2020)

Add to Collection

Article Energy & Fuels

Current Enhancement via a TiO2 Window Layer for CSS Sb2Se3 Solar Cells: Performance Limits and High VOC

Laurie J. Phillips et al.

IEEE JOURNAL OF PHOTOVOLTAICS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

A study on optical properties of Sb2Se3 thin films and resistive switching behavior in Ag/Sb2Se3/W heterojunctions

Chunmin Liu et al.

RESULTS IN PHYSICS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Complicated and Unconventional Defect Properties of the Quasi-One-Dimensional Photovoltaic Semiconductor Sb2Se3

Menglin Huang et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

Add to Collection

Article Optics

Effects of substrate temperature on material and photovoltaic properties of magnetron-sputtered Sb2Se3 thin films

Shiming Chen et al.

APPLIED OPTICS (2019)

Add to Collection

Article Energy & Fuels

Alternative back contacts for Sb2Se3 solar cells

Jun Zhang et al.

SOLAR ENERGY (2019)

Add to Collection

Review Chemistry, Multidisciplinary

New Earth-Abundant Thin Film Solar Cells Based on Chalcogenides

Alessia Le Donne et al.

FRONTIERS IN CHEMISTRY (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Quasiepitaxy Strategy for Efficient Full-Inorganic Sb2S3 Solar Cells

Hui Deng et al.

ADVANCED FUNCTIONAL MATERIALS (2019)

Add to Collection

Article Energy & Fuels

Efficiency improvement of Sb2Se3 solar cells based on La-doped SnO2 buffer layer

Zhiwen Chen et al.

SOLAR ENERGY (2019)

Add to Collection

Article Chemistry, Physical

Solution-processed SnO2 interfacial layer for highly efficient Sb2Se3 thin film solar cells

Jiahua Tao et al.

NANO ENERGY (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Orientation Engineering in Low-Dimensional Crystal-Structural Materials via Seed Screening

Kanghua Li et al.

ADVANCED MATERIALS (2019)

Add to Collection

Article Energy & Fuels

Enhancement of Sb2Se3 thin-film solar cell photoelectric properties by addition of interlayer CeO2

Xin Wang et al.

SOLAR ENERGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

5.91%-efficient Sb2Se3 solar cells with a radio-frequency magnetron-sputtered CdS buffer layer

Xiaobo Hu et al.

APPLIED MATERIALS TODAY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Structural, optical, optoelectrical and photovoltaic properties of the thermally evaporated Sb2Se3 thin films

I. M. El Radaf

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2019)

Add to Collection

Article Engineering, Electrical & Electronic

Effect of selenization temperature on the properties of Sb2Se3 thin films and solar cells by two-step method

Shubing Li et al.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Improvement in Sb2Se3 Solar Cell Efficiency through Band Alignment Engineering at the Buffer/Absorber Interface

Gang Li et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Interfacial Engineering by Indium-Doped CdS for High Efficiency Solution Processed Sb2(S1-xSex)3 Solar Cells

Chunyan Wu et al.

ACS APPLIED MATERIALS & INTERFACES (2019)

Add to Collection

Article Chemistry, Physical

Highly efficient and stable planar heterojunction solar cell based on sputtered and post-selenized Sb2Se3 thin film

Rong Tang et al.

NANO ENERGY (2019)

Add to Collection

Article Energy & Fuels

Interfacial engineering for high efficiency solution processed Sb2Se3 solar cells

Xiaomin Wang et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2019)

Add to Collection

Article Multidisciplinary Sciences

9.2%-efficient core-shell structured antimony selenide nanorod array solar cells

Zhiqiang Li et al.

NATURE COMMUNICATIONS (2019)

Add to Collection

Article Energy & Fuels

Enhancement in the Efficiency of Sb2Se3 Thin-Film Solar Cells by Increasing Carrier Concertation and Inducing Columnar Growth of the Grains

Huafei Guo et al.

SOLAR RRL (2019)

Add to Collection

Article Chemistry, Physical

The complex defect chemistry of antimony selenide

ChristopherN. Savory et al.

JOURNAL OF MATERIALS CHEMISTRY A (2019)

Add to Collection

Article Energy & Fuels

Alkali Metals Doping for High-Performance Planar Heterojunction Sb2S3 Solar Cells

Chenhui Jiang et al.

SOLAR RRL (2019)

Add to Collection

Article Energy & Fuels

Efficient Copper-Doped Antimony Sulfide Thin-Film Solar Cells via Coevaporation Method

Muhammad Ishaq et al.

SOLAR RRL (2019)

Add to Collection

Review Energy & Fuels

Review of Recent Progress in Antimony Chalcogenide-Based Solar Cells: Materials and Devices

Hongwei Lei et al.

SOLAR RRL (2019)

Add to Collection

Article Chemistry, Physical

Controlled synthesis of (hk1) preferentially oriented Sb2Se3 rod arrays by co-evaporation for photovoltaic applications

Si-Nae Park et al.

JOURNAL OF MATERIALS CHEMISTRY A (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Overview of thin film deposition techniques

Olayinka Oluwatosin Abegunde et al.

AIMS MATERIALS SCIENCE (2019)

Add to Collection

Article Chemistry, Physical

7.5% n-i-p Sb2Se3 solar cells with CuSCN as a hole-transport layer

Kanghua Li et al.

JOURNAL OF MATERIALS CHEMISTRY A (2019)

Add to Collection

Article Energy & Fuels

Interface Engineering via Sputtered Oxygenated CdS:O Window Layer for Highly Efficient Sb2Se3 Thin-Film Solar Cells with Efficiency Above 7%

Liping Guo et al.

SOLAR RRL (2019)

Add to Collection

Article Energy & Fuels

Improved efficiency by insertion of Zn1-xMgxO through sol-gel method in ZnO/Sb2Se3 solar cell

Kanghua Li et al.

SOLAR ENERGY (2018)

Add to Collection

Article Energy & Fuels

Direct solution deposition of device quality Sb2S3-xSex films for high efficiency solar cells

Chunyan Wu et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2018)

Add to Collection

Article Energy & Fuels

ZnSnP2 solar cell with (Cd,Zn)S buffer layer: Analysis of recombination rates

Shunsuke Akari et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2018)

Add to Collection

Article Energy & Fuels

Investigation of electrically-active defects in Sb2Se3 thin-film solar cells with up to 5.91% efficiency via admittance spectroscopy

Xiaobo Hu et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2018)

Add to Collection

Article Multidisciplinary Sciences

Vapor transport deposition of antimony selenide thin film solar cells with 7.6% efficiency

Xixing Wen et al.

NATURE COMMUNICATIONS (2018)

Add to Collection

Article Physics, Applied

Sb2(S1-xSex)3 solar cells: the impact of radiative and non-radiative loss mechanisms

Thalia Jimenez et al.

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2018)

Add to Collection

Review Chemistry, Physical

Sb2S3 Solar Cells

Rokas Kondrotas et al.

JOULE (2018)

Add to Collection

Review Chemistry, Multidisciplinary

Copper indium gallium selenide based solar cells - a review

Jeyakumar Ramanujam et al.

ENERGY & ENVIRONMENTAL SCIENCE (2017)

Add to Collection

Article Energy & Fuels

Enhanced Sb2Se3 solar cell performance through theory-guided defect control

Xinsheng Liu et al.

PROGRESS IN PHOTOVOLTAICS (2017)

Add to Collection

Review Green & Sustainable Science & Technology

Review: Progress in solar cells from hydrogenated amorphous silicon

Michael Stuckelberger et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2017)

Add to Collection

Article Energy & Fuels

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

Zhiqiang Li et al.

SOLAR ENERGY MATERIALS AND SOLAR CELLS (2017)

Add to Collection

Article Chemistry, Physical

6.5% Certified Efficiency Sb2Se3 Solar Cells Using PbS Colloidal Quantum Dot Film as Hole-Transporting Layer

Chao Chen et al.

ACS ENERGY LETTERS (2017)

Add to Collection

Article Energy & Fuels

Stable 6%-efficient Sb2Se3 solar cells with a ZnO buffer layer

Liang Wang et al.

NATURE ENERGY (2017)

Add to Collection

Proceedings Paper Energy & Fuels

Review of New Technology for Preparing Crystalline Silicon Solar Cell Materials by Metallurgical Method

Man Li et al.

2017 3RD INTERNATIONAL CONFERENCE ON ENERGY, ENVIRONMENT AND MATERIALS SCIENCE (EEMS 2017) (2017)

Add to Collection

Article Engineering, Electrical & Electronic

Characterization of basic physical properties of Sb2Se3 and its relevance for photovoltaics

Chao Chen et al.

FRONTIERS OF OPTOELECTRONICS (2017)

Add to Collection

Review Materials Science, Multidisciplinary

Inorganic photovoltaics - Planar and nanostructured devices

Jeyakumar Ramanujam et al.

PROGRESS IN MATERIALS SCIENCE (2016)

Add to Collection

Article Chemistry, Multidisciplinary

The effect of sodium on antimony selenide thin film solar cells

Yang Li et al.

RSC ADVANCES (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Atmospheric annealing effect on TiO2/Sb2S3/P3HT heterojunction hybrid solar cell performance

M. Kamruzzaman et al.

RSC ADVANCES (2016)

Add to Collection

Article Physics, Applied

Optical properties of amorphous and polycrystalline Sb2Se3 thin films prepared by thermal evaporation

Chao Chen et al.

APPLIED PHYSICS LETTERS (2015)

Add to Collection

Article Physics, Applied

Physics of grain boundaries in polycrystalline photovoltaic semiconductors

Yanfa Yan et al.

JOURNAL OF APPLIED PHYSICS (2015)

Add to Collection

Review Engineering, Electrical & Electronic

Metal Chalcogenide Nanocrystalline Solid Thin Films

Soumya R. Deo et al.

JOURNAL OF ELECTRONIC MATERIALS (2015)

Add to Collection

Article Optics

Thin-film Sb2Se3 photovoltaics with oriented one-dimensional ribbons and benign grain boundaries

Ying Zhou et al.

NATURE PHOTONICS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of chlorine doping on the structural, morphological, optical and electrical properties of spray deposited CdS thin films

T. Sivaraman et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2015)

Add to Collection

Article Energy & Fuels

Improving the performance of Sb2Se3 thin film solar cells over 4% by controlled addition of oxygen during film deposition

Xinsheng Liu et al.

PROGRESS IN PHOTOVOLTAICS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of chlorine doping on the structural, morphological, optical and electrical properties of spray deposited CdS thin films

T. Sivaraman et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2015)

Add to Collection

Article Chemistry, Multidisciplinary

Highly Improved Sb2S3 Sensitized-Inorganic-Organic Heterojunction Solar Cells and Quantification of Traps by Deep-Level Transient Spectroscopy

Yong Chan Choi et al.

ADVANCED FUNCTIONAL MATERIALS (2014)

Add to Collection

Article Chemistry, Multidisciplinary

Sb2Se3-Sensitized Inorganic-Organic Heterojunction Solar Cells Fabricated Using a Single-Source Precursor

Yong Chan Choi et al.

ANGEWANDTE CHEMIE-INTERNATIONAL EDITION (2014)

Add to Collection

Article Physics, Applied

Selenization of Sb2Se3 absorber layer: An efficient step to improve device performance of CdS/Sb2Se3 solar cells

Meiying Leng et al.

APPLIED PHYSICS LETTERS (2014)

Add to Collection

Review Chemistry, Multidisciplinary

Physics and chemistry of CdTe/CdS thin film heterojunction photovoltaic devices: fundamental and critical aspects

S. Girish Kumar et al.

ENERGY & ENVIRONMENTAL SCIENCE (2014)

Add to Collection

Article Physics, Applied

InGaP/GaAs tandem solar cells fabricated using solid-source molecular beam epitaxy

Takeyoshi Sugaya et al.

JAPANESE JOURNAL OF APPLIED PHYSICS (2014)

Add to Collection

Article Chemistry, Physical

Solution-Processed Antimony Selenide Heterojunction Solar Cells

Ying Zhou et al.

ADVANCED ENERGY MATERIALS (2014)

Add to Collection

Article Chemistry, Physical

Efficient Inorganic-Organic Heterojunction Solar Cells Employing Sb2(Sx/Se1-x)3 Graded-Composition Sensitizers

Yong Chan Choi et al.

ADVANCED ENERGY MATERIALS (2014)

Add to Collection

Article Physics, Applied

Dielectric function of Cu(In, Ga)Se2-based polycrystalline materials

Shota Minoura et al.

JOURNAL OF APPLIED PHYSICS (2013)

Add to Collection

Article Engineering, Electrical & Electronic

Synthesis, structure and optical properties of Sb2Se3

H. Maghraoui-Meherzi et al.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2013)

Add to Collection

Article Chemistry, Physical

Electrical impact of MoSe2 on CIGS thin-film solar cells

Kuo-Jui Hsiao et al.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2013)

Add to Collection

Article Energy & Fuels

Polycrystalline silicon PV modules performance and degradation over 20years

Davide Polverini et al.

PROGRESS IN PHOTOVOLTAICS (2013)

Add to Collection

Article Physics, Multidisciplinary

Identification of Potential Photovoltaic Absorbers Based on First-Principles Spectroscopic Screening of Materials

Liping Yu et al.

PHYSICAL REVIEW LETTERS (2012)

Add to Collection

Article Energy & Fuels

Implications for CdTe and CIGS technologies production costs of indium and tellurium scarcity

Chiara Candelise et al.

PROGRESS IN PHOTOVOLTAICS (2012)

Add to Collection

Article Chemistry, Inorganic & Nuclear

First principles prediction of the elastic, electronic, and optical properties of Sb2S3 and Sb2Se3 compounds

H. Koc et al.

SOLID STATE SCIENCES (2012)

Add to Collection

Article Chemistry, Multidisciplinary

VESTA 3 for three-dimensional visualization of crystal, volumetric and morphology data

Koichi Momma et al.

JOURNAL OF APPLIED CRYSTALLOGRAPHY (2011)

Add to Collection

Article Chemistry, Multidisciplinary

Toward Interaction of Sensitizer and Functional Moieties in Hole-Transporting Materials for Efficient Semiconductor-Sensitized Solar Cells

Sang Hyuk Im et al.

NANO LETTERS (2011)

Add to Collection

Article Physics, Condensed Matter

Electronic structure of antimony selenide (Sb2Se3) from GW calculations

Rajesekarakumar Vadapoo et al.

PHYSICA STATUS SOLIDI B-BASIC SOLID STATE PHYSICS (2011)

Add to Collection

Article Green & Sustainable Science & Technology

Abundant non-toxic materials for thin film solar cells: Alternative to conventional materials

Fahhad Alharbi et al.

RENEWABLE ENERGY (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Chemically deposited thin films of PbSe as an absorber component in solar cell structures

Enue Barrios-Salgado et al.

THIN SOLID FILMS (2011)

Add to Collection

Article Chemistry, Multidisciplinary

High-Performance Nanostructured Inorganic-Organic Heterojunction Solar Cells

Jeong Ah Chang et al.

NANO LETTERS (2010)

Add to Collection

Article Chemistry, Physical

Sb2S3-Sensitized Nanoporous TiO2 Solar Cells

Yafit Itzhaik et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2009)

Add to Collection

Article Electrochemistry

Antimony Selenide Absorber Thin Films in All-Chemically Deposited Solar Cells

Sarah Messina et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2009)

Add to Collection

Article Physics, Condensed Matter

Effect of heat treatment on the structural and optical properties of amorphous Sb2Se3 and Sb2Se2S thin films

E. A. El-Sayad et al.

PHYSICA B-CONDENSED MATTER (2009)

Add to Collection

Article Engineering, Mechanical

Rotatable Magnetron Sputter Technology for Large Area Glass and Web Coating

Anja Blondeel et al.

VAKUUM IN FORSCHUNG UND PRAXIS (2009)

Add to Collection

Article Materials Science, Ceramics

Compositional dependence of the optical properties of amorphous Sb2Se3-xSx thin films

E. A. El-Sayad

JOURNAL OF NON-CRYSTALLINE SOLIDS (2008)

Add to Collection

Article Physics, Condensed Matter

Electrical conduction and optical properties of amorphous (Sb2Se3)100-xSnx thin films

Praveen Kumar et al.

SOLID STATE COMMUNICATIONS (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Polycrystalline thin films of antimony selenide via chemical bath deposition and post deposition treatments

Y Rodríguez-Lazcano et al.

THIN SOLID FILMS (2005)

Add to Collection

Article Chemistry, Inorganic & Nuclear

Solar energy conversion by dye-sensitized photovoltaic cells

M Grätzel

INORGANIC CHEMISTRY (2005)

Add to Collection

Review Energy & Fuels

Thin-film solar cells: An overview

KL Chopra et al.

PROGRESS IN PHOTOVOLTAICS (2004)

Add to Collection

Article Materials Science, Multidisciplinary

Equipment, materials and processes:: a review of high rate sputtering technology for glass coating

SJ Nadel et al.

THIN SOLID FILMS (2003)

Add to Collection

Review Materials Science, Coatings & Films

Plasma deposition of optical films and coatings: A review

L Martinu et al.

JOURNAL OF VACUUM SCIENCE & TECHNOLOGY A (2000)

Add to Collection

Review Materials Science, Multidisciplinary

Chemical deposition method for metal chalcogenide thin films

RS Mane et al.

MATERIALS CHEMISTRY AND PHYSICS (2000)

Add to Collection

Article Green & Sustainable Science & Technology

Comparison of minority carrier diffusion length measurements in silicon solar cells by the photo-induced open-circuit voltage decay (OCVD) with different excitation sources

U Stutenbaeumer et al.

RENEWABLE ENERGY (2000)

Add to Collection

Article Materials Science, Multidisciplinary

Recrystallization in CdTe/CdS

A Romeo et al.

THIN SOLID FILMS (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.