☆ 4.6 Article

Breakdown mechanism of RTV silicone rubber coated insulators under steep-front impulse voltage

ELECTRIC POWER SYSTEMS RESEARCH (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Electrical & Electronic

Modified model of AC flashover voltages of contaminated insulators with various shapes

Bingbing Dong et al.

Summary: The introduction of additional leakage distance is an important factor in improving the flashover voltage of contaminated insulators. Researchers have optimized insulator parameters, such as leakage distance, profile, diameter, and form factor, to enhance the flashover voltage. A mathematical model based on the Obenaus-Rizk model is established to accurately predict the flashover voltage for polluted insulators. The model is able to analyze the influence of contamination degree, arc constants, and geometric parameters on the critical flashover voltage and flashover voltage gradient, and it has been validated with experimental data.

ELECTRIC POWER SYSTEMS RESEARCH (2023)

Add to Collection

Article Engineering, Electrical & Electronic

An method for power lines insulator defect detection with attention feedback and double spatial pyramid

Jiangli Chen et al.

Summary: With the increasing use of UAVs in electric power inspection, inspection efficiency has significantly improved. However, dealing with massive aerial images remains a challenge. This paper introduces a method that combines Attention Feedback and Double Spatial Pyramid to enhance the detection precision of insulator defects and detect sheltered insulators.

ELECTRIC POWER SYSTEMS RESEARCH (2023)

Add to Collection

Article Engineering, Electrical & Electronic

Optimal design of high voltage composite insulators with grading rings in different configurations

Mohammed Khalil Hussain et al.

Summary: The paper proposes a method to find the optimal geometrical design of composite insulators for different voltage levels, which relies on achieving the lowest electric field strength. Five different optimization algorithms are applied and compared to find the optimal geometric design. The results show that the particle swarm optimization (PSO) algorithm produces the best results in terms of minimizing the electric field strength.

ELECTRIC POWER SYSTEMS RESEARCH (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Simultaneous Optimization of the Surface Hydrophobicity and Surface Charge Distribution of Insulating Materials

Shuming Liu et al.

Summary: Superhydrophobic materials have great application potential in power systems insulation equipment due to their water-repelling and self-cleaning abilities. However, their electrical performance has been overlooked, highlighting the need for an optimization of both hydrophobic and electrical characteristics in insulating materials.

MACROMOLECULAR MATERIALS AND ENGINEERING (2022)

Add to Collection

Article Engineering, Electrical & Electronic

Effects of dynamic deformation of pendant water drops on the electric field between hollow porcelain insulator sheds under extreme rainfall

Yijie Sun et al.

Summary: This study investigates the spatial and temporal variation of electric fields between hollow porcelain insulator sheds affected by dynamic deformation of pendant water drops. The results show that the maximum electric field increases significantly after the breakup of the water drop, and its position alters accordingly. The influence of dimensionless numbers and factors on the electric field behavior is discussed in detail.

HIGH VOLTAGE (2022)

Add to Collection

Article Engineering, Multidisciplinary

Lightning flashover characteristics of a full-scale AC 500 kV transmission tower with composite cross arms

Qian Wang et al.

Engineering (2022)

Add to Collection

Review Engineering, Electrical & Electronic

Comparative Investigation on Fracture of Suspension High Voltage Composite Insulators: A Review-Part I: Fracture Morphology Characteristics

Yanfeng Gao et al.

Summary: This article focuses on the fracture morphology characteristics of various fracture modes in high voltage composite suspension insulators, including normal fracture, brittle fracture, and decay-like fracture.

IEEE ELECTRICAL INSULATION MAGAZINE (2021)

Add to Collection

Article Engineering, Electrical & Electronic

Breakdown process on rod-rod air gap under oscillating lightning impulse voltage

Akif Guerlek

HIGH VOLTAGE (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Influence of ageing on oil degradation and gassing tendency under high-energy electrical discharge faults for mineral oil and synthetic ester

L. Loiselle et al.

HIGH VOLTAGE (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Improving the Outdoor Insulation Performance of Chinese EHV and UHV AC and DC Overhead Transmission Lines

Xidong Liang et al.

IEEE ELECTRICAL INSULATION MAGAZINE (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Charge distribution on polymer insulator surface under AC voltage

Dayu Li et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2019)

Add to Collection

Article Engineering, Electrical & Electronic

Decay-like Fracture Mechanism of Silicone Rubber Composite Insulator

Xidong Liang et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2018)

Add to Collection

Review Engineering, Electrical & Electronic

Research and application of UHV power transmission in China

Yinbiao Shu et al.

HIGH VOLTAGE (2018)

Add to Collection

Article Engineering, Electrical & Electronic

A Modified 5000 h Test Procedure for Silicone Rubber Insulator Based on Contamination and Hydrophobicity Change Simulation

Shaohua Li et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2017)

Add to Collection

Article Engineering, Electrical & Electronic

Effects of AC and DC Corona on the Surface Properties of Silicone Rubber: Characterization by Contact Angle Measurements and XPS High Resolution Scan

Weining Bao et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2017)

Add to Collection

Article Engineering, Electrical & Electronic

Transfer of Hydrophobicity of Polymeric Insulating Materials for High Voltage Outdoor Application

Alexander Hergert et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2017)

Add to Collection

Article Engineering, Electrical & Electronic

Steep-front Impulse Voltage in Diagnostic Studies of Composite Insulators

Krzysztof Wieczorek et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2016)

Add to Collection

Article Engineering, Electrical & Electronic

Development of Time- and Cost-Effective Pollution Test Methods Applicable for Different Station Insulation Options

Igor Gutman et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2014)

Add to Collection

Article Engineering, Electrical & Electronic

Field Experience and Laboratory Investigation of Glass Insulators having a Factory-applied Silicone Rubber Coating

J. -M. George et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2014)

Add to Collection

Article Engineering, Electrical & Electronic

Influence of Biofilm Contamination on Electrical Performance of Silicone Rubber Based Composite Materials

Jing Wang et al.

IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION (2012)

Add to Collection

Article Engineering, Electrical & Electronic

Study on DC Pollution Flashover Performance of Various Types of Long String Insulators Under Low Atmospheric Pressure Conditions

Zhijin Zhang et al.

IEEE TRANSACTIONS ON POWER DELIVERY (2010)

Add to Collection

© Peeref 2019-2024. All rights reserved.