☆ 4.7 Article

3D printing of high solid loading zirconia feedstock via screw-based material extrusion

CERAMICS INTERNATIONAL (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Material extrusion additive manufacturing of advanced ceramics: Towards the production of large components

Frank Clemens et al.

Summary: Thermoplastic extrusion based additive manufacturing (MEX-AM) is an interesting method for fabricating large ceramic parts. Three commercial yttria-stabilized zirconia (YSZ) filaments provided by Fabru GmbH, SiCeram GmbH, and PT+A GmbH were investigated. The flexibility and rheological properties of YSZ filaments were found to vary greatly. The Fabru filament exhibited higher flexibility but required significantly higher extrusion pressure to be printed through a 0.25 mm nozzle. In the SiCeram filament, a grain orientation effect was observed. STA analysis suggested that the polymer decomposing at a high temperature in the Fabru filament could be removed by solvent debinding (SD). Finally, the printing and post-processing of YSZ filaments were evaluated using a 70 mm tall cup structure.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

Extrusion-based 3D printing of fully dense zirconia ceramics for dental restorations

Sun Jiaxiao et al.

Summary: In this study, an optimized extrusion-based 3D printing method was developed for fabricating intricate, fully dense ceramics based on gelled zirconia suspensions. The viscoelastic properties of the suspensions were tailored to enable smooth flow through a small nozzle and produce self-supporting features. The as-dried zirconia specimens could be directly sintered without the need for binder-removal steps. Zirconia dental restorations were successfully fabricated, and occlusal details were preserved by co-printing a temperature-dependent polyacrylate supporting material.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Engineering, Manufacturing

A review on metallic and ceramic material extrusion method: Materials, rheology, and printing parameters

Xiang Ang et al.

Summary: Ink-based printing or direct ink writing (DIW) is a method that deposits ink-based material layer by layer to form a 3D article, and it can be used to 3D print metal and ceramic materials when combined with metallurgy processing. This review focuses on the latest progress in metallic and ceramic materials through DIW, including printability based on ink blends and properties, as well as parametric analysis. Ink printability, determined by ink flow and extruded shape maintenance, is crucial for DIW success. Different ink compositions and printing parameters play important roles in achieving optimal printing results.

JOURNAL OF MANUFACTURING PROCESSES (2023)

Add to Collection

Review Chemistry, Multidisciplinary

Photopolymerization of Ceramic Resins by Stereolithography Process: A Review

Alessandro Bove et al.

Summary: This review discusses the characteristics and properties of ceramic resins and the stereolithography process, as well as the complexity of post-processing phases.

APPLIED SCIENCES-BASEL (2022)

Add to Collection

Article Chemistry, Physical

Injection Molding and Sintering of ZrO2 Ceramic Powder Modified by a Zirconate Coupling Agent

Qiangyi Mao et al.

Summary: This paper investigates the effects of different coupling media and sintering temperatures on the rheological characteristics, densities, microstructures, and mechanical properties of ceramic components. The results show that the use of zirconate coupling agent with ethanol medium can improve the flowability of feedstocks and help achieve green parts with high powder loading and bending strength.

MATERIALS (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Binder jet 3D printing?Process parameters, materials, properties, modeling, and challenges*

Amir Mostafaei et al.

Summary: Binder jet 3D printing, as a non-beam-based additive manufacturing method, shows great promise in rapid production of complex structures, but faces challenges in optimizing printing and post-processing methods. Understanding the physical processes during 3D printing and the science of densification post-sintering is crucial for enhancing part performance.

PROGRESS IN MATERIALS SCIENCE (2021)

Add to Collection

Article Materials Science, Ceramics

Additive manufacturing of dense zirconia ceramics by fused deposition modeling via screw extrusion

Qinglong He et al.

Summary: A fused deposition modeling (FDM) system using screw extrusion for feeding granular feedstocks with high solid loading was developed. By optimizing key parameters and determining a processing window, constant extruded mass flow and wire diameter were achieved, leading to successful preparation of zirconia ceramic parts with complex geometries and controlled dimensional accuracy, demonstrating the potential of the technique.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Chemistry, Physical

Printing of Zirconia Parts via Fused Filament Fabrication

Dorit Noetzel et al.

Summary: This work presents a process chain for the fabrication of dense zirconia parts, focusing on the rheological characterization of feedstock systems. The study successfully achieved dense ceramic parts with structural details smaller than 100 μm.

MATERIALS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Chemical Emissions from Cured and Uncured 3D-Printed Ventilator Patient Circuit Medical Parts

Jordan E. Krechmer et al.

Summary: Research showed that emissions of volatile organic compounds (VOCs) from medical parts produced using 3D printing technology are heavily dependent on postprint curing, and decrease over time.

ACS OMEGA (2021)

Add to Collection

Article Materials Science, Ceramics

Fused deposition fabrication of high-quality zirconia ceramics using granular feedstock

Ting Shen et al.

Summary: This study fabricated 3D zirconia ceramics using granular feedstock and analyzed their morphology, surface quality, and the effect of thermal accumulation on structure. The research showed that small printing size increased thermal accumulation and decreased printing quality.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Review Dentistry, Oral Surgery & Medicine

Additive Manufacturing of Zirconia Ceramic and Its Application in Clinical Dentistry: A Review

Leila Nasiry Khanlar et al.

Summary: Zirconia, a popular dental ceramic material due to its outstanding properties, is increasingly being utilized in dentistry with the potential for additive manufacturing. Research has shown promising outcomes in utilizing additive manufacturing of zirconia in restorative, implant, and regenerative dentistry, but further improvements and validation are needed for its clinical application.

DENTISTRY JOURNAL (2021)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

The Effects of Sintering Additives on the Sintering of 3Y-TZP Ceramic

S. Theenagaran et al.

Summary: The study investigated the influence of 0.5 wt.% manganese oxide doping on 3Y-TZP, showing that under specific sintering conditions, the doped samples exhibited good mechanical properties.

INTERNATIONAL CONFERENCE ON ADVANCED ENGINEERING AND TECHNOLOGY (ICAET 2020) (2021)

Add to Collection

Article Materials Science, Ceramics

Theory and practice of rapid and safe thermal debinding in ceramic injection molding

Hehan Xie et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Additive manufacturing of zirconia ceramics: a state-of-the-art review

Xiuping Zhang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Synergy of solid loading and printability of ceramic paste for optimized properties of alumina via stereolithography-based 3D printing

Weiwei Liu et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Effects of Solvent Debinding on the Microstructure and Properties of 3D-Printed Alumina Ceramics

He Li et al.

ACS OMEGA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Fracture toughness enhancement of yttria-stabilized tetragonal zirconia polycrystalline ceramics through magnesia-partially stabilized zirconia addition

Bilal Soylemez et al.

JOURNAL OF SCIENCE-ADVANCED MATERIALS AND DEVICES (2020)

Add to Collection

Article Materials Science, Ceramics

Investigation of the solvent debinding in the injection molding of ZrO2 ceramics using LDEP, HDPE and wax binders

Manman Zhao et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Debinding behaviour of feedstock for material extrusion additive manufacturing of zirconia

Christian Kukla et al.

POWDER METALLURGY (2019)

Add to Collection

Review Engineering, Manufacturing

A comprehensive review of extrusion-based additive manufacturing processes for rapid production of metallic and ceramic parts

Kedarnath Rane et al.

ADVANCES IN MANUFACTURING (2019)

Add to Collection

Article Materials Science, Ceramics

Stereolithography-based additive manufacturing of gray-colored SiC ceramic green body

Guojiao Ding et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Effect of surface treatment on the dispersion of nano zirconia particles in non-aqueous suspensions for stereolithography

Jinxing Sun et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Review Materials Science, Ceramics

3D printing of ceramics: A review

Zhangwei Chen et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Composites

Can the melt flow index be used to predict the success of fused deposition modelling of commercial poly(lactic acid) filaments into 3D printed materials?

Sisi Wang et al.

PLASTICS RUBBER AND COMPOSITES (2018)

Add to Collection

Article Dentistry, Oral Surgery & Medicine

Strength and fracture toughness of zirconia dental ceramics

Miquel Turon-Vinas et al.

DENTAL MATERIALS (2018)

Add to Collection

Article Thermodynamics

Application of thermal analysis in the selection of polymer components used as a binder for metal injection moulding of Co-Cr-Mo alloy powder

Grzegorz Matula et al.

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Critical evaluation of indentation fracture toughness measurements with Vickers indenter on yttria-stabilized zirconia dental ceramics

D. Coric et al.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK (2017)

Add to Collection

Proceedings Paper Engineering, Mechanical

Study of solvent debinding parameters for metal injection moulded 316L stainless steel

M. F. F. A. Hamidi et al.

4TH INTERNATIONAL CONFERENCE ON MECHANICAL ENGINEERING RESEARCH (ICMER2017) (2017)

Add to Collection

Proceedings Paper Engineering, Mechanical

Paraffin wax removal from metal injection moulded cocrmo alloy compact by solvent debinding process

N. A. N. Dandang et al.

4TH INTERNATIONAL CONFERENCE ON MECHANICAL ENGINEERING RESEARCH (ICMER2017) (2017)

Add to Collection

Article Materials Science, Ceramics

Effect of two-step sintering on the hydrothermal ageing resistance of tetragonal zirconia polycrystals

U. Sutharsini et al.

CERAMICS INTERNATIONAL (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Suppressing Crack Formation in Particulate Systems by Utilizing Capillary Forces

Monica Schneider et al.

ACS APPLIED MATERIALS & INTERFACES (2017)

Add to Collection

Article Engineering, Environmental

Assessing and Reducing the Toxicity of 3D-Printed Parts

Shirin Mesbah Oskui et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY LETTERS (2016)

Add to Collection

Article Engineering, Industrial

Effect of high-temperature preheating on the selective laser melting of yttria-stabilized zirconia ceramic

Qi Liu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)

Add to Collection

Article Materials Science, Ceramics

Change in the phase composition, structure and mechanical properties of directed melt crystallised partially stabilised zirconia crystals depending on the concentration of Y2O3

M. A. Borik et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2015)

Add to Collection

Article Engineering, Biomedical

Long-time aging in 3 mol.% yttria-stabilized tetragonal zirconia polycrystals at human body temperature

Melanie Keuper et al.

ACTA BIOMATERIALIA (2014)

Add to Collection

Article Engineering, Industrial

Influence of paraffin wax characteristics on the formulation of wax-based binders and their debinding from green molded parts using two comparative techniques

M. T. Zaky et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Minimum Amount of Binder Removal Required during Solvent Debinding of Powder-Injection-Molded Compacts

Yang-Liang Fan et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Improvement of the dimensional stability of powder injection molded compacts by adding swelling inhibitor into the debinding solvent

Yang-Liang Fan et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)

Add to Collection

Article Nanoscience & Nanotechnology

Critical thickness in binder removal process for injection molded compacts

YM Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.