4.7 Article

The effect of temperature on detwinning and mechanical properties of face-centered cubic deformation twins

Related references

Note: Only part of the references are listed.
Article Materials Science, Multidisciplinary

Detwinning Phenomenon and Its Effect on Resulting Twinning Structure of an Austenitic Hadfield Steel

Marina Lukas et al.

Summary: Hadfield Steel demonstrates high strain hardening attributed to twin formation during mechanical loading. While twin formation in Hadfield Steel is well-documented, detwinning is poorly understood. Detwinning contributes to plastic deformation and may be crucial during cyclic loading. This study focuses on the twinning and detwinning behavior in Hadfield Steel through interrupted tensile tests conducted within a scanning electron microscope. Electron backscatter diffraction analysis reveals the appearance of the first twins after 5 to 10 pct strain, and partial detwinning at 30 and 40 pct elongation. Kernel Average Misorientation analysis indicates high misorientation in both twinned and detwinned regions, linking it to the twinning/detwinning process.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2023)

Article Nanoscience & Nanotechnology

Detwinning of face-centered cubic deformation twins at liquid nitrogen temperature

M. J. Szczerba et al.

Summary: The study shows that low temperature detwinning of deformation twins in the twin/matrix structure of Cu-8at.%Al microstructure does not perturb the activity of face-centered cubic detwinning modes. These detwinning systems contribute significantly to the crystal plasticity and mechanical properties at low temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Article Nanoscience & Nanotechnology

Portevin-Le Chatelier effect, twinning-detwinning and disordering in an aged Ni-Cr-Mo alloy during large plastic deformation

Wanjun He et al.

Summary: Portevin-Le Chatelier (PLC) effects, twinning-detwinning, and disordering phenomena were observed and investigated in long-range ordered (LRO) phase strengthened Ni-Cr-Mo alloys during hot compression. The results showed that the PLC effects with type-C serrations occurred in the solution-treated and aged alloys, with the Pt2Mo-type LRO phase increasing the serration amplitude at the early stage of deformation. However, twinning of aged alloy was only activated after the early stage of deformation, and deformation twins and the Pt2Mo-type LRO phase were not stable during severe deformation. The potential disordering process of the LRO phase was suggested to be dislocation slipping on the two valid {111}<110> slip systems, and detwinning mechanism was likely the dislocation-twin boundary interaction as indicated by steps on the twin boundaries of remanent deformation twins.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Article Nanoscience & Nanotechnology

Direct monitoring of twinning/detwinning in a TWIP steel under reversed cyclic loading

C. D'Hondt et al.

Summary: In situ tensile and reversed cyclic tests were conducted on a TWIP steel in a SEM, showing evidence of twinning/detwinning processes and their effects. It was observed that detwinning and retwinning occurred partially after load reversal, with stress variations close to twinning stress affecting the mechanical hysteresis of the material.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Review Materials Science, Multidisciplinary

Annealing-Induced Hardening in Ultrafine-Grained and Nanocrystalline Materials

Jeno Gubicza

ADVANCED ENGINEERING MATERIALS (2020)

Article Nanoscience & Nanotechnology

Reversible deformation in nanocrystalline TWIP steel during cyclic loading by partial slip reversal and detwinning

Roghayeh Mohammadzadeh

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Article Materials Science, Multidisciplinary

A study on crystal plasticity of face-centered cubic structures induced by deformation twinning

M. S. Szczerba et al.

ACTA MATERIALIA (2020)

Article Nanoscience & Nanotechnology

Detwinning-twinning behavior during compression of face-centered cubic twin-matrix layered microstructure

M. J. Szczerba et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Article Multidisciplinary Sciences

Scale law of complex deformation transitions of nanotwins in stainless steel

A. Y. Chen et al.

NATURE COMMUNICATIONS (2019)

Article Materials Science, Multidisciplinary

On the first direct observation of de-twinning in a twinning-induced plasticity steel

Scott J. McCormack et al.

ACTA MATERIALIA (2018)

Article Materials Science, Multidisciplinary

Slip versus twinning in low and very low stacking-fault energy Cu-Al alloy single crystals

M. J. Szczerba et al.

ACTA MATERIALIA (2017)

Article Materials Science, Multidisciplinary

Detwinning of face-centered cubic deformation twins via the correspondence matrix approach

M. J. Szczerba et al.

ACTA MATERIALIA (2016)

Article Materials Science, Multidisciplinary

Experimental studies on detwinning of face-centered cubic deformation twins

M. J. Szczerba et al.

ACTA MATERIALIA (2016)

Article Materials Science, Multidisciplinary

On the reverse mode of fcc deformation twinning

M. S. Szczerba et al.

ACTA MATERIALIA (2012)

Article Nanoscience & Nanotechnology

Transformation of dislocations during twin variant reorientation in Ni-Mn-Ga martensite structures

Maciej J. Szczerba et al.

SCRIPTA MATERIALIA (2012)

Article Materials Science, Multidisciplinary

Is there a critical resolved shear stress for twinning in face-centred cubic crystals?

MS Szczerba et al.

PHILOSOPHICAL MAGAZINE (2004)

Article Materials Science, Multidisciplinary

The onset of twinning in metals:: A constitutive description

MA Meyers et al.

ACTA MATERIALIA (2001)