☆ 4.7 Article

In situ probing of interfacial roughness and transient phases during ceramic cold sintering process

ACTA MATERIALIA (2023)

Related references

Note: Only part of the references are listed.

Review Materials Science, Ceramics

Reassessing cold sintering in the framework of pressure solution theory

Arnaud Ndayishimiye et al.

Summary: This study examines the densification and coarsening mechanisms in cold sintering from the perspective of pressure solution creep. It is found that the cold sintering process of BaTiO3, ZnO, and KH2PO4 ceramic materials follows a similar sequential process as pressure solution creep. The study also suggests that using appropriate transient solvents can lead to advances in densification, microstructural control, and reductions in cold sintering pressure.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

The effect of liquid phase chemistry on the densification and strength of cold sintered ZnO

Abdullah Jabr et al.

Summary: Cold sintering is a chemo-mechanical densification process that enables ceramics to be densified at low temperatures below 300 degrees C. This paper investigates the effect of different commercial organic acids, namely formic, acetic, and citric acid, on the densification, microstructural evolution, and mechanical response of cold-sintered ZnO. The results show that formic and acetic acid achieve high relative densities (>96%), while citric acid exhibits poor densification (<80%), despite its higher expected solubility of zinc oxide. Fractographic analyses support the finding of higher biaxial strength in samples sintered with formic acid compared to acetic acid (i.e. -90 MPa vs. -40 MPa).

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

Cold Sintering Process characterization by in operando electrochemical impedance spectroscopy

Thomas Herisson de Beauvoir et al.

Summary: This paper presents the application of in situ impedance analysis in the Cold Sintering Process (CSP), specifically focusing on the influence of acetic acid on the sintering of ZnO and the resulting ceramics. The results demonstrate that this in situ characterization technique has the potential to be applied to a wide range of materials.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Morphological and chemical evolution of transient interfaces during zinc oxide cold sintering process

S.H. Bang et al.

Materials Today Chemistry (2022)

Add to Collection

Article Chemistry, Multidisciplinary

In Situ Microstructure Characterization of Potassium Di-Phosphate (KDP) Densification during Cold Sintering

Andrew J. Allen et al.

Summary: This article introduces the application of cold sintering process in ceramic additive manufacturing for the model system, potassium di-phosphate (KDP). The in situ study reveals that temperature and applied stress affect the densification rate and morphology evolution of the ceramic product, with stress having a greater impact.

APPLIED SCIENCES-BASEL (2022)

Add to Collection

Article Materials Science, Ceramics

In situ doping of BaTiO3and visualization of pressure solution in flux-assisted cold sintering

Takao Sada et al.

Summary: Cold sintering process (CSP) is an innovative technique with extremely low processing temperatures, fast processing times, and simplicity to densify ceramics and composites. By investigating the chemical transformation at solid/flux interfaces, the significant role of pressure solution creep in the densification process has been successfully visualized.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Physics, Applied

Cold sintering, enabling a route to co-sinter an all-solid-state lithium-ion battery

Joo-Hwan Seo et al.

Summary: The cold sintering process significantly reduces the manufacturing cost and difficulty of solid-state lithium-ion batteries while maintaining high performance, with high capacity and cycle life retention.

JAPANESE JOURNAL OF APPLIED PHYSICS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Cold sintering of microwave dielectric ceramics and devices

Dawei Wang et al.

Summary: MW dielectric ceramics are essential for electronic components in wireless communication systems, but traditional high-temperature sintering methods limit their integration with other materials. Cold sintering, a process at lower temperatures, offers energy-efficient densification and better compatibility with diverse materials. Current research focuses on improving cold-sintered MW materials and devices, addressing challenges like unclear mechanisms and poor mechanical properties.

JOURNAL OF MATERIALS RESEARCH (2021)

Add to Collection

Article Materials Science, Ceramics

In situ characterization of ceramic cold sintering by small-angle scattering

Andrew J. Allen et al.

Summary: This study presents the first in situ characterization of pore morphology evolution during the cold sintering process using small-angle X-ray scattering methods. The researchers observed nanoscale structural features associated with the dissolution and reprecipitation of KDP close to the grain/pore interface during CSP. Future experiments are planned to explore quantitative measurements under different temperature and pressure conditions, as well as to study technologically important materials like ZnO.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Chemistry, Physical

The Role of the Activator Additives Introduction Method in the Cold Sintering Process of ZnO Ceramics: CSP/SPS Approach

Yurii D. Ivakin et al.

Summary: The study analyzed the effect of introducing zinc acetate into ZnO powder using different methods on the density and grain size of sintered ceramics. Impregnation method resulted in higher relative density and significant grain growth, while TVT and aqueous solution direct injection methods showed lower relative densities for CSP ZnO samples. Additionally, the study presented developments in understanding processes in an aqueous medium subjected to mechanical pressure during CSP and TVT.

MATERIALS (2021)

Add to Collection

Review Materials Science, Ceramics

The cold sintering process: A review on processing features, densification mechanisms and perspectives

Anna Galotta et al.

Summary: Cold sintering process (CSP) has gained global attention for its environmentally friendly and innovative fabrication route, reducing processing time, energy, and costs significantly. The process densifies ceramic powder with the aid of a liquid phase under intense pressure and limited heating conditions, achieving extraordinary results. The review explores processing features, possible densification mechanisms, and challenges, paving the way for new processing opportunities in the future.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Pressure-dependent topographic evolutions of cold-sintered zinc oxide surfaces

Sun Hwi Bang et al.

Summary: This study utilized atomic force microscope to study pressure-dependent topographic evolutions in flat polycrystalline microstructures, using a cold-sintered zinc oxide as a model system. The research demonstrated a methodology for quantifying relative grain boundary energetics in cold-sintered materials and identified distinct changes in anisotropic grain growth, normal grain growth, and particle coarsening under different pressures. The growth kinetics were found to be a function of pressure, with morphological changes connected to underlying mechanochemical phenomena.

JOURNAL OF MATERIALS CHEMISTRY C (2021)

Add to Collection

Article Materials Science, Ceramics

A theoretical analysis of cold sintering

Mattia Biesuz et al.

ADVANCES IN APPLIED CERAMICS (2020)

Add to Collection

Review Materials Science, Ceramics

A review of cold sintering processes

Salvatore Grasso et al.

ADVANCES IN APPLIED CERAMICS (2020)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process of ZnO ceramics: Effect of the nanoparticle/microparticle ratio

Aida Serrano et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Cold sintering zinc oxide with a crystalline zinc acetate dihydrate mass transport phase

Richard D. Floyd et al.

JOURNAL OF MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Ceramics

Broad temperature dependence, high conductivity, and structure-property relations of cold sintering of LLZO-based composite electrolytes

Joo-Hwan Seo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Chemistry, Physical

Densification of a Solid-State NASICON Sodium-Ion Electrolyte Below 400 °C by Cold Sintering With a Fused Hydroxide Solvent

Zane M. Grady et al.

ACS APPLIED ENERGY MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Anisothermal densification kinetics of the cold sintering process below 150 °C

Sun Hwi Bang et al.

JOURNAL OF MATERIALS CHEMISTRY C (2020)

Add to Collection

Article Materials Science, Ceramics

Mechanism studies of hydrothermal cold sintering of zinc oxide at near room temperature

Xiaoyu Kang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Preparation of high density ZnO ceramics by the Cold Sintering Process

Xupeng Jiang et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Chemistry, Physical

Effects of water content during cold sintering process of NaCl ceramics

Lei Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Cold Sintering: Progress, Challenges, and Future Opportunities

Jing Guo et al.

ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 49 (2019)

Add to Collection

Article Materials Science, Ceramics

Sintering mechanisms and dielectric properties of cold sintered (1-x) SiO2 - x PTFE composites

Arnaud Ndayishimiye et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Geochemistry & Geophysics

Influence of Grain Boundary Structural Evolution on Pressure Solution Creep Rates

M. P. A. van den Ende et al.

JOURNAL OF GEOPHYSICAL RESEARCH-SOLID EARTH (2019)

Add to Collection

Article Materials Science, Ceramics

Cold Sintering of ZnO Ceramic in Water Medium: Test Demonstration

Yu D. Ivakin et al.

GLASS AND CERAMICS (2019)

Add to Collection

Article Materials Science, Ceramics

Comparing hydrothermal sintering and cold sintering process: Mechanisms, microstructure, kinetics and chemistry

Arnaud Ndayishimiye et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical strength of cold-sintered zinc oxide under biaxial bending

Sarah Lowum et al.

JOURNAL OF MATERIALS SCIENCE (2019)

Add to Collection

Article Materials Science, Ceramics

Decarbonising ceramic manufacturing: A techno-economic analysis of energy efficient sintering technologies in the functional materials sector

T. Ibn-Mohammed et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Unveiling the mechanisms of cold sintering of ZnO at 250 degrees C by varying applied stress and characterizing grain boundaries by Kelvin Probe Force Microscopy

J. Gonzalez-Julian et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Ceramics

Remarkably improved electrical conductivity of ZnO ceramics by cold sintering and post-heat-treatment

Yang Jing et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Review Chemistry, Multidisciplinary

Recent Progress in Applications of the Cold Sintering Process for Ceramic-Polymer Composites

Jing Guo et al.

ADVANCED FUNCTIONAL MATERIALS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

ReaxFF Molecular Dynamics Study on the Influence of Temperature on Adsorption, Desorption, and Decomposition at the Acetic Acid/Water/ZnO(10(1)over-bar0) Interface Enabling Cold Sintering

Mert Y. Sengul et al.

ACS APPLIED MATERIALS & INTERFACES (2018)

Add to Collection

Article Materials Science, Ceramics

Demonstration of the cold sintering process study for the densification and grain growth of ZnO ceramics

Shuichi Funahashi et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process: A new era for ceramic packaging and microwave device development

Jing Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Review Materials Science, Multidisciplinary

Cold sintering: Current status and prospects

Jon-Paul Maria et al.

JOURNAL OF MATERIALS RESEARCH (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process of Li1.5Al0.5Ge1.5(PO4)3 solid electrolyte

Seth S. Berbano et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Cold sintering process for 8 mol%Y2O3-stabilized ZrO2 ceramics

Hanzheng Guo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Microwave dielectric properties of mineral sillimanite obtained by conventional and cold sintering process

I. J. Induja et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Polymer Science

Fast-responding bio-based shape memory thermoplastic polyurethanes

Zoran S. Petrovic et al.

POLYMER (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Current progress and perspectives of applying cold sintering process to ZrO2-based ceramics

Hanzheng Guo et al.

SCRIPTA MATERIALIA (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Hydrothermal-Assisted Cold Sintering Process: A New Guidance for Low-Temperature Ceramic Sintering

Hanzheng Guo et al.

ACS APPLIED MATERIALS & INTERFACES (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Cold Sintering Process of Composites: Bridging the Processing Temperature Gap of Ceramic and Polymer Materials

Jing Guo et al.

ADVANCED FUNCTIONAL MATERIALS (2016)

Add to Collection

Article Chemistry, Multidisciplinary

Cold Sintering: A Paradigm Shift for Processing and Integration of Ceramics

Jing Guo et al.

ANGEWANDTE CHEMIE-INTERNATIONAL EDITION (2016)

Add to Collection

Article Materials Science, Ceramics

Cold Sintering Process: A Novel Technique for Low-Temperature Ceramic Processing of Ferroelectrics

Hanzheng Guo et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Ceramics

Utilizing the Cold Sintering Process for Flexible-Printable Electroceramic Device Fabrication

Amanda Baker et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2016)

Add to Collection

Software Review Chemistry, Multidisciplinary

GSAS-II: the genesis of a modern open-source all purpose crystallography software package

Brian H. Toby et al.

JOURNAL OF APPLIED CRYSTALLOGRAPHY (2013)

Add to Collection

Software Review Chemistry, Multidisciplinary

Nika: software for two-dimensional data reduction

Jan Ilavsky

JOURNAL OF APPLIED CRYSTALLOGRAPHY (2012)

Add to Collection

Software Review Chemistry, Multidisciplinary

Irena: tool suite for modeling and analysis of small-angle scattering

Jan Ilavsky et al.

JOURNAL OF APPLIED CRYSTALLOGRAPHY (2009)

Add to Collection

Article Geochemistry & Geophysics

Influence of grain boundary structure on dissolution controlled pressure solution and retarding effects of grain boundary healing

Reinier van Noort et al.

JOURNAL OF GEOPHYSICAL RESEARCH-SOLID EARTH (2008)

Add to Collection

Article Chemistry, Inorganic & Nuclear

Sodalite networks formed by metal squarates

S Neeraj et al.

SOLID STATE SCIENCES (2002)

Add to Collection

Article Geochemistry & Geophysics

Compaction creep of quartz sand at 400-600°C:: experimental evidence for dissolution-controlled pressure solution

A Niemeijer et al.

EARTH AND PLANETARY SCIENCE LETTERS (2002)

Add to Collection

Article Materials Science, Characterization & Testing

X-ray powder diffraction data for selected metal soaps

MC Corbeil et al.

POWDER DIFFRACTION (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.