☆ 4.0 Article

Comparative Study of Mechanical Performance of AlCrSiN Coating Deposited on WC-Co and cBN Hard Substrates

CERAMICS-SWITZERLAND (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Spherical indentation of polycrystalline cubic boron nitride (PcBN): Contact damage evolution with increasing load and microstructural effects

S. Gordon et al.

Summary: The severe conditions of hard machining operations require tools with exceptional mechanical properties. This study investigates the damage scenario of polycrystalline cubic boron nitride (PcBN) through controlled damage induction. The results show that higher-grade PcBN exhibits higher resistance to crack nucleation and a more gradual transition between damage scenarios, which can be attributed to the higher hardness and fracture toughness of that grade. The different crack paths and toughness mechanisms observed in the PcBN grades contribute to their effective crack growth resistance. Higher fracture toughness is observed in the grade with a higher content of cBN particles, while the grade with a lower amount of superhard particles shows lower crack growth resistance. These differences in crack resistance are key in understanding enhanced contact damage behavior.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2023)

Add to Collection

Article Materials Science, Ceramics

Micromechanical mapping of polycrystalline cubic boron nitride composites by means of high-speed nanoindentation: Assessment of microstructural assemblage effects

S. Gordon et al.

Summary: High-speed nanoindentation is used to evaluate the micromechanical properties of polycrystalline cubic boron nitride and correlate them with the microstructure for performance optimization. The obtained mechanical maps and data sets are statistically treated using 1D and 2D Gaussian fitting. The technique is reliable for assessing intrinsic mechanical properties and mirroring microstructural assemblage, although challenges and disparities exist for fine-grained microstructures.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2023)

Add to Collection

Article Materials Science, Ceramics

Contact fatigue of WC-6%wtCo cemented carbides: Influence of corrosion-induced changes on emergence and evolution of damage

Y. F. Zheng et al.

Summary: The study investigates the effect of corrosion on the contact fatigue response and associated damage in a medium-grained WC-6%wtCo hardmetal grade. Corrosion is found to significantly impact the material's contact fatigue behavior, leading to gradual and diffuse damage evolution under corroded conditions. These findings are rationalized based on phase changes linked to corrosion, highlighting the impact on toughening capability and WC grain pull-out ease.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Design of cycle structure on microstructure, mechanical properties and tribology behavior of AlCrN/AlCrSiN coatings

Ying Gao et al.

Summary: AlCrN/AlCrSiN coatings with cycle structure, composed of fcc-CrN, hcp-AlN and amorphous Si3N4 phases, were fabricated using high energy ion source enhanced multi-arc ion plating technology. The crystal grains of the coatings were refined and the growth behavior transformed with increasing cycle structure. The coating with two cycle structure exhibited better adhesion strength, higher hardness, better fracture toughness, lower friction coefficient, less wear rate, and longer service life.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Influence of microstructural assemblage of the substrate on the adhesion strength of coated PcBN grades

S. Gordon et al.

Summary: Research on the mechanical integrity of coated polycrystalline cubic boron nitride (PcBN) tools is limited. This study investigates the adhesion strength of two TiN/TiAlN-coated PcBN substrates with different microstructures. Results show that the damage scenario evolves from adhesive delamination to radial cracking and spalling. The high cBN-content grade exhibits higher resistance to radial cracking and delamination.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Chemistry, Physical

Mechanical Performance of AlCrSiN and AlTiSiN Coatings on Inconel and Steel Substrates after Thermal Treatments

Jing Liang et al.

Summary: This study aimed to explore the mechanical properties of AlCrSiN and AlTiSiN coatings on Inconel and steel substrates after thermal treatments. Nanoindentation, microindentation, microscratch, Mercedes tests, optical microscopy, SEM, and FIB were used for evaluation. The results showed that AlCrSiN coatings and Inconel substrates exhibited superior mechanical performance, even after thermal treatments.

MATERIALS (2022)

Add to Collection

Article Materials Science, Coatings & Films

Investigation on plastic deformation of arc-evaporated AlCrSiN and AlCrSiON nanocomposite films by indentation

Zhengtao Wu et al.

Summary: This study investigated the plastic deformation of arc-evaporated AlCrSiN and AlCrSiON nanocomposite films deposited on cemented-carbide substrates using nanoindentation. The results showed that both films exhibited excellent plasticity without microcrack initiation and propagation. The AlCrSiON film displayed a prominent pile-up phenomenon, while incorporating oxygen into the AlCrSiN film reduced its hardness and toughness, resulting in pile-up as well.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Coatings & Films

Evolution of structure, residual stress, thermal stability and wear resistance of nanocrystalline multilayered Al0.7Cr0.3N-Al0.67Ti0.33N coatings

S. Spor et al.

Summary: The study used cross-sectional X-ray nanodiffraction to investigate depth gradients of the structure and residual stress in multilayer coatings. Results showed that a sublayer thickness between 70 and 100 nm is the ideal thickness for reducing wear rate by a factor of 10 at high temperatures.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Engineering, Industrial

Tool wear mechanisms of PcBN in machining Inconel 718: Analysis across multiple length scale

Volodymyr Bushlya et al.

Summary: The study found that the wear mechanisms of PcBN tooling when machining Ni-based superalloys mainly include diffusional dissolution and oxidation, with tool protection phenomena also observed. Oxidation of Inconel 718 results in the formation of a protective layer on the tool, which helps counterbalance tool wear.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

The synergy of V and Si on the microstructure, tribological and oxidation properties of AlCrN based coatings

Yu Chen et al.

Summary: This study investigates the synergistic effects of V and Si on the microstructure, tribological and oxidation properties of AlCrN coatings. It is found that the addition of Si can promote the transition from c-Al(Cr)N solid solution to h-Al(Cr)N solid solution, ultimately forming a nanocomposite structure. The Al0.58Cr0.31V0.04Si0.07N coating shows the best resistance to plastic deformation, the lowest wear rate, and high oxidation resistance temperature due to the synergy of V and Si.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Investigations into friction and wear behavior of AlTiN and AlCrN coatings deposited on laser textured WC/Co using novel open tribometer tests

Sarvesh Kumar Mishra et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Coatings & Films

Evaluation of the adhesion and failure mechanism of the hard CrN coatings on different substrates

Xin Zhang et al.

SURFACE & COATINGS TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Edge toughness of tungsten carbide based hardmetals

A. J. Gant et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2018)

Add to Collection

Article Materials Science, Coatings & Films

Enhancement of toughness and wear resistance by CrN/CrCN multilayered coatings for wood processing

Ying Kong et al.

SURFACE & COATINGS TECHNOLOGY (2018)

Add to Collection

Article Electrochemistry

Thermal treatment effect on structural and mechanical properties of Cr-C coatings

M. Fellah et al.

TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

An investigation on the crack resistance of CrN, CrBN and CrTiBN coatings via nanoindentation

Qianzhi Wang et al.

VACUUM (2017)

Add to Collection

Article Engineering, Mechanical

Scratch adhesion and tribological behaviour of graded Cr/CrN/CrTiN coatings synthesized by closed-field unbalanced magnetron sputtering

Mohammad Sharear Kabir et al.

WEAR (2017)

Add to Collection

Article Materials Science, Coatings & Films

Evaluating mechanical properties and crack resistance of CrN, CrTiN, CrAlN and CrTiAlN coatings by nanoindentation and scratch tests

Qianzhi Wang et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of 10% Si addition on cathodic arc evaporated TiAlSiN coatings

Li-hui Zhu et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2016)

Add to Collection

Article Engineering, Mechanical

Influence of substrate microstructure and surface finish on cracking and delamination response of TiN-coated cemented carbides

J. Yang et al.

WEAR (2016)

Add to Collection

Article Chemistry, Physical

Preparation and Characterization of Ni Spines Grown on the Surface of Cubic Boron Nitride Grains by Electroplating Method

Yanghai Gui et al.

MATERIALS (2016)

Add to Collection

Article Engineering, Chemical

Characterization and Rockwell-C adhesion properties of chromium-based borided steels

Yusuf Kayali et al.

JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Improved thermal stability and oxidation resistance of Al-Ti-N coating by Si addition

Li Chen et al.

THIN SOLID FILMS (2014)

Add to Collection

Article Engineering, Mechanical

Scratch adhesion characteristics of PVD TiAlN deposited on high speed steel, cemented carbide and PCBN substrates

S. Sveen et al.

WEAR (2013)

Add to Collection

Proceedings Paper Nanoscience & Nanotechnology

Thermal Oxidation Behavior of TiAlCrSiN and AlCrTiN Films on HastelloyX

K. Tuchida et al.

NANOTECHNOLOGY AND ADVANCED MATERIALS (2012)

Add to Collection

Article Chemistry, Physical

Characteristics of PVD-CrAlSiN films after post-coat heat treatments in nitrogen atmosphere

Wei-Yu Ho et al.

APPLIED SURFACE SCIENCE (2011)

Add to Collection

Article Nanoscience & Nanotechnology

Advantages of Nanoimpact Fracture Testing in Studying the Mechanical Behavior of CrAl(Si)N Coatings

A. Mosquera et al.

NANOSCIENCE AND NANOTECHNOLOGY LETTERS (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Contact fatigue behavior of PVD-coated hardmetals

E. Tarres et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of residual stresses on mechanical properties and interface adhesion strength of SiN thin films

Yi-Chung Huang et al.

THIN SOLID FILMS (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Analyses of interface adhesion between porous SiOCH low-k film and SiCN layers by nanoindentation and nanoscratch tests

Shou-Yi Chang et al.

THIN SOLID FILMS (2008)

Add to Collection

Article Automation & Control Systems

CBN tool wear in hard turning: a survey on research progresses

Yong Huang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)

Add to Collection

Article Materials Science, Multidisciplinary

TiN coating on an electrical discharge machined WC-Co hardmetal: surface integrity effects on indentation adhesion response

B. Casas et al.

JOURNAL OF MATERIALS SCIENCE (2006)

Add to Collection

Review Materials Science, Multidisciplinary

Different approaches to superhard coatings and nanocomposites

S Veprek et al.

THIN SOLID FILMS (2005)

Add to Collection

Article Nanoscience & Nanotechnology

Avoiding the high-temperature decomposition and softening of (Al1-xTix)N coatings by the formation of stable superhard nc-(Al1-xTix)N/a-Si3N4 nanocomposite

S Veprek et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)

Add to Collection

Review Materials Science, Multidisciplinary

Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology

WC Oliver et al.

JOURNAL OF MATERIALS RESEARCH (2004)

Add to Collection

Article Materials Science, Coatings & Films

Synthesis and mechanical properties of Cr-Si-N coatings deposited by a hybrid system of arc ion plating and sputtering techniques

JH Park et al.

SURFACE & COATINGS TECHNOLOGY (2004)

Add to Collection

Article Engineering, Industrial

The VDI 3198 indentation test evaluation of a reliable qualitative control for layered compounds

N Vidakis et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

Article Engineering, Mechanical

Wear resistance of coatings in high speed gear hobbing

J Rech et al.

WEAR (2001)

Add to Collection

Article Materials Science, Multidisciplinary

Trends and recent developments in the material manufacture and cutting tool application of polycrystalline diamond and polycrystalline cubic boron nitride

MW Cook et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.