☆ 4.4 Article

Effect of Carbide Orientation on Wear Characteristics of High-Alloy Wear-Resistant Cast Irons

LUBRICANTS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Effect of in-situ (Ti&W)C multiphase particles on three-body abrasive wear of high chromium cast iron

Shuai Wang et al.

Summary: The effect of in-situ (Ti&W)C multiphase particles on the microstructure and three-body abrasive wear behavior of high chromium cast iron was investigated in this study. The different W/Ti ratios in the preforms resulted in significant differences in the microstructure and properties of the composites. The composite with a W/Ti ratio of 4/6 (M3) showed the best microstructure and wear resistance.

MATERIALS CHEMISTRY AND PHYSICS (2023)

Add to Collection

Article Engineering, Mechanical

Fabrication and abrasive wear property of high chromium cast iron with high vanadium and high nitrogen content (HCCI-VN)

Liujie Xu et al.

Summary: To improve the wear resistance of high chromium cast irons (HCCIs), a new HCCI-VN was fabricated by replacing 5.0 wt% chromium with 5.0 wt% vanadium and adding 0.1 wt% nitrogen. The HCCI-VN exhibited excellent wear resistance, with a relative wear resistance 2.2-9.1 times higher than traditional HCCI.

WEAR (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of strength and toughness of ceramic particles on impact abrasive wear resistance of iron matrix composites

Yue Wang et al.

Summary: In this study, three kinds of ceramic particle reinforced iron matrix composites were prepared by powder metallurgy method, and their mechanical properties, impact abrasive wear resistance, and impact abrasive wear mechanism were studied. Results showed that the ZTA/Fe45 composite exhibited better impact wear resistance than the other two composites. The wear mechanism of the Fe45 matrix involved micro-furrow and plastic deformation. The phase transformation of ceramic particles in the composites was also analyzed. The t -> m phase transformation in ZTA particles increased the toughness of the composite, improving its impact abrasive wear resistance.

MATERIALS TODAY COMMUNICATIONS (2023)

Add to Collection

Article Engineering, Mechanical

Experimental visualization of the wear and scuffing evolution of a flake graphite cast iron cylinder liner

Jakob Gussmagg et al.

Summary: This paper investigates the origin and evolution of scuffing in a ring-on-liner contact using an experimental approach. A four-stage scuffing hypothesis is developed based on the analysis. The first stage involves the formation of a scaly structure on the liner surface due to smearing of the honing structure and formation of surface cracks. The second stage is characterized by the formation of breakouts in the liner surface due to crack growth induced by adhesive shear forces.

WEAR (2023)

Add to Collection

Article Engineering, Mechanical

Three-Body Abrasive Wear Performance of High Chromium White Cast Iron with Different Ti and C Content

Mohammad Jobayer Huq et al.

Summary: The content of Ti and C has a significant impact on the hardness and wear resistance of high chromium white cast iron (HCCI). The addition of Ti decreases the hardness but increases the wear rate, while the addition of C increases the hardness and wear resistance. HCCI performs better in wear resistance when the Ti content is low and the C content is high.

LUBRICANTS (2022)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Three-body-type Abrasive Wear Behavior of Multi-alloyed White Cast Iron with Different Carbon Contents Used for Hot Work Rolls

Sudsakorn Inthidech et al.

Summary: The research focused on the three-body abrasive wear behavior of heat-treated multi-alloyed white cast irons. The study found that the wear rate decreased with increasing C content under different heat treatment conditions, while As-H specimens exhibited higher wear resistance compared to tempered specimens. Additionally, the lowest wear rate was observed in specimens tempered at the maximum tempered hardness temperature, and the best wear resistance was obtained in As-H specimens with 2.34% C content.

ISIJ INTERNATIONAL (2021)

Add to Collection

Article Engineering, Mechanical

Erosive wear characteristics of high-chromium based multi-component white cast irons

Riki Hendra Purba et al.

Summary: The research found that the quenched specimens have better erosive wear resistance, but the tempering process slightly reduces their performance. This indicates that excessive Cr addition has a negative impact on erosive wear resistance in heat-treated conditions.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Engineering, Multidisciplinary

Effect of Soaking Temperature on Carbide Precipitation, Hardness, and Wear Resistance of High-Chromium Cast Iron

Kaushal Kishore et al.

JOURNAL OF FAILURE ANALYSIS AND PREVENTION (2020)

Add to Collection

Article Engineering, Mechanical

Microstructural evaluation and high-temperature erosion characteristics of high chromium cast irons

Kazumichi Shimizu et al.

WEAR (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Vanadium on Microstructure and Wear Resistance of High Chromium Cast Iron Hardfacing Layer by Electroslag Surfacing

Hao Wang et al.

METALS (2018)

Add to Collection

Article Engineering, Mechanical

Abrasive wear characteristics of Fe-2C-5Cr-5Mo-5W-5Nb multi-component white cast iron

Kenta Kusumoto et al.

WEAR (2017)

Add to Collection

Article Engineering, Mechanical

Influence of tribology on global energy consumption, costs and emissions

Kenneth Holmberg et al.

FRICTION (2017)

Add to Collection

Article Materials Science, Multidisciplinary

High erosion-oxidation performance of Fe-based Nb or V containing multi-component alloys with Co addition at 1173 K

Kenta Kusumoto et al.

MATERIALS & DESIGN (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Fe-Cr-C-Nb white cast irons

Mirjana Filipovic et al.

MATERIALS & DESIGN (2013)

Add to Collection

Article Engineering, Mechanical

Abrasive wear mechanisms of multi-components ferrous alloys abraded by soft, fine abrasive particles

Jose Daniel B. de Mello et al.

WEAR (2010)

Add to Collection

Article Engineering, Mechanical

Effects of titanium addition on microstructure and wear resistance of hypereutectic high chromium cast iron Fe-25wt.%Cr-4wt.%C

R. J. Chung et al.

WEAR (2009)

Add to Collection

Article Materials Science, Multidisciplinary

An investigation of the wear behaviours of white cast irons under different compositions

C Cetinkaya

MATERIALS & DESIGN (2006)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Analysis of carbides in multi-component white cast iron for hot rolling mill rolls

M Hashimoto et al.

ISIJ INTERNATIONAL (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.