☆ 4.8 Article

Improving reciprocal tribo-mechanical performance and corrosion resistance using carbide ceramics: T6 thermal-treated A333 mono-hybrid functionally graded composites

MATERIALS TODAY CHEMISTRY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Textiles

Flexural behavior of functionally graded polymeric composite beams

M. Atta et al.

Summary: The bending test of functionally graded polymeric composite materials is investigated both experimentally and numerically, showing that the gradient pattern and V-f% of the outer layers are critical for improving flexural behavior. Delamination failure between layers plays a major role in the rapidity of final failure.

JOURNAL OF INDUSTRIAL TEXTILES (2022)

Add to Collection

Review Engineering, Multidisciplinary

Influence of various trace metallic additions and reinforcements on A319 and A356 alloys-a review

D. Srinivas et al.

Summary: This article covers aspects related to A319 and A356 alloys in the automotive and aerospace industries. It discusses the importance of collecting overall information about these alloys and processing them for future improvement of material properties. The addition of various trace metallic elements such as Mg, Sr, Sc, Cu, No, Ti, B, Mn, V, Zr, and Ca can help improve the alloys' tensile properties. The article also discusses various methods and heat treatment processes that can be used to produce and improve the alloys.

COGENT ENGINEERING (2022)

Add to Collection

Article Materials Science, Ceramics

Interfacial characteristics and wear performances of iron matrix composites reinforced with zirconia-toughened alumina ceramic particles

Cong Li et al.

Summary: This study investigated the interfacial characteristics, wear behaviors, and fabrication methods of ZTA(P)/Fe composites. By optimizing sintering conditions and infiltration casting process, high-quality composites with improved wear resistance compared to Cr15 specimens were obtained.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Chemistry, Physical

Strength-ductility balance strategy in SiC reinforced aluminum matrix composites via deformation-driven metallurgy

Dongxin Mao et al.

Summary: The strategy of strength-ductility balance in aluminum matrix composites reinforced with nano- and micro-SiC particles was designed through deformation-driven metallurgy. Grain refinement and optimization of SiC particles were key to achieving increased ultimate tensile strength and ductility in the composite materials.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Polymer Science

Mechanical and Tribological Behavior of Functionally Graded Unidirectional Glass Fiber-Reinforced Epoxy Composites

Waleed Alhazmi et al.

Summary: This paper experimentally assesses the mechanical and tribological behavior of conventional and functionally graded polymeric matrix composites reinforced with continuous glass fibers. The results show that the wear rate and flexural capacity can be improved by varying the glass fiber layers and volume fraction.

POLYMERS (2022)

Add to Collection

Article Engineering, Industrial

Utilization of machining chips waste for production of functionally gradient magnesium matrix composites

Bassiouny Saleh et al.

Summary: This study produced lightweight functionally gradient materials through centrifugal casting method, utilizing AZ91D magnesium chips reinforced with boron carbide particles. The influence of reuse magnesium chips and strengthening mechanisms on the formation and mechanical characteristics of the graded composites was investigated. Pre-mixing technique improved particle distribution inside the matrix, and the outer region showed better mechanical characteristics. The experimental values were in good agreement with the theoretical values.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Engineering, Mechanical

Wear characteristics of functionally graded composites synthesized from magnesium chips waste

Bassiouny Saleh et al.

Summary: This study attempted to produce a gradient composite reinforced with silicon carbide particles using recycled magnesium chips, aiming to evaluate its wear behavior. The findings showed that the use of magnesium chips led to a significant improvement in the distribution and gradient of particles within the matrix, resulting in enhanced wear characteristics. The graded composite with chips exhibited higher hardness and wear resistance compared to the composite without chips and the AZ91D alloy.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of the Effect of Sr on the Mechanical Properties and Microstructure of Nano-Alumina Reinforced Aluminum Matrix Composites by the Vortical Casting Method

Sadegh Shahriyari et al.

Summary: The study investigated the use of vortical casting to prevent the agglomeration of alumina nanoparticles in molten aluminum, with a focus on the influence of strontium as a reformer material on the microstructure of the composite substrate. Results showed that the optimal amount of strontium for modifying the eutectic structure of silicon and improving the wettability of the A356 alloy is 0.5%. Higher amounts of strontium led to the formation of intermetallic Al2Si2Sr particles, with the highest reported strength at 191 MPa.

METALS AND MATERIALS INTERNATIONAL (2021)

Add to Collection

Article Chemistry, Physical

Comparative Study on Reciprocal Tribology Performance of Mono-Hybrid Ceramic Reinforced Al-9Si-3Cu Graded Composites

Manu Sam et al.

Summary: This research compares the reciprocating tribo-mechanical behavior of different materials, showing that the hybrid composite has superior performance, particularly in terms of higher hardness and tensile strength.

SILICON (2021)

Add to Collection

Article Engineering, Civil

Influence of gradient structure on wear characteristics of centrifugally cast functionally graded magnesium matrix composites for automotive applications

Bassiouny Saleh et al.

Summary: The study investigated the microstructural and wear properties of AZ91 alloy reinforced with silicon carbide particles produced through centrifugal casting method. Results showed that the gradient distribution of SiC particles within the AZ91 matrix substantially improved hardness and wear resistance for the FG tubes, with mold rotational speed being the main factor in controlling particle distribution.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Jingjing Li et al.

Summary: The SiC/Al-Zn-Mg-Cu nanocomposites were fabricated through high energy ball milling combined with spark plasma sintering and hot extrusion, leading to increased strength and decreased ductility with higher content of SiC nanoparticles. Various strengthening mechanism calculation results suggest that Orowan strengthening played a significant role in improving the strength of the T6 heat treated SiC/Al-Zn-Mg-Cu nanocomposites.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure, heat treatment and mechanical properties of TiB2/Al-7Si-Cu-Mg alloy fabricated by selective laser melting

Y. K. Xiao et al.

Summary: Selective laser melting (SLM) of aluminium alloys is a research focus for fabricating complex components in aerospace and automotive industries. This study demonstrated the effects of post heat treatment on microstructures and mechanical properties, showing that SLMed TiB2/Al-7Si-Cu-Mg samples can achieve appropriate mechanical properties through post-heat treatments.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Ceramics

Study on the joining of ceramic matrix composites to an Al alloy for advanced brake systems

Valentina Casalegno et al.

Summary: The integration of ceramic matrix composites (CMCs) and an Al alloy for high-performance road brake discs involves using a specific epoxy adhesive and heat treatment to achieve joints with decent strength. Corrosion in high-salinity environments has little effect on the mechanical strength of the joints.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Effect of light weight reinforcement and heat treatment process parameters on morphological and wear aspects of hypoeutectic Al-Si based composites-a critical review

K. Nithesh et al.

Summary: The study focuses on the importance of aluminum matrix composites with light weight reinforcements in engineering applications, especially in wear-related scenarios. By investigating the effects of different reinforcements on aluminum composites, it is possible to enhance their properties and expand their applications in aerospace, automotive, and marine transportation industries.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Engineering, Multidisciplinary

Enhancing strength-ductility synergy and mechanisms of Al-based composites by size-tunable in-situ TiB2 particles with specific spatial distribution

Bai-Xin Dong et al.

Summary: This study successfully tailored the microstructures of Al-Si-based composites by designing and synthesizing in-situ TiB2 particles, leading to enhanced mechanical performance and breaking the traditional trade-off dilemma between strength and ductility.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Review Engineering, Manufacturing

Progression in manufacturing of functionally graded materials and impact of thermal treatment-A critical review

Manu Sam et al.

Summary: This paper reviews the evolution of production technologies and the impact of thermal treatment on FGMs, as well as the classification of alloys and ceramics used in FGM manufacturing and their engineering applications. It discusses the correlation between fabrication techniques and industrial requirements, as well as comparing advanced research outcomes on various aspects of FGMs.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Tribological characterization of LM26/SiC/Ni.-Gr. Hybrid aluminium matrix composites (HAMCs) for high temperature applications

Suyash Y. Pawar et al.

Summary: This study investigated the tribological characteristics of the hybrid composite material LM26/SiC/Ni.-Gr. under different temperature conditions. It was found that the hybridization of hard and soft reinforcements improved the composite's tribological and mechanical performance under high temperature sliding wear conditions. Load and temperature were identified as primary factors affecting the performance of both pure aluminum alloys and hybrid composites, with low wear loss and friction coefficient observed in high-temperature wear tests. The LM26 + 20% SiC + 2%Ni.-Gr. hybrid composite showed the highest improvement in tribological performance, with SEM analysis indicating increased wear resistance.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Review on the Influence of Different Reinforcements on the Microstructure and Wear Behavior of Functionally Graded Aluminum Matrix Composites by Centrifugal Casting

Bassiouny Saleh et al.

METALS AND MATERIALS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Composites

Tribo-performance assessment of milled fly ash brake friction composites

Vishal Ahlawat et al.

POLYMER COMPOSITES (2020)

Add to Collection

Article Chemistry, Physical

Tribo-Mechanical Behaviour of Ti-Based Particulate Reinforced As-Cast and Heat Treated A359 Composites

N. Radhika et al.

SILICON (2020)

Add to Collection

Article Engineering, Civil

Study of the microstructure and mechanical characteristics of AZ91-SiCpcomposites fabricated by stir casting

Bassiouny Saleh et al.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical and tribological properties of AA7075-T6 metal matrix composite reinforced with ceramic particles and aloevera ash via Friction stir processing

Lakshay Tyagi et al.

MATERIALS RESEARCH EXPRESS (2020)

Add to Collection

Article Engineering, Multidisciplinary

30 Years of functionally graded materials: An overview of manufacturing methods, Applications and Future Challenges

Bassiouny Saleh et al.

COMPOSITES PART B-ENGINEERING (2020)

Add to Collection

Review Materials Science, Composites

Tribological characterization of particulate-reinforced aluminum metal matrix nanocomposites: A review

Deepak M. Shinde et al.

ADVANCED COMPOSITES LETTERS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Effect of Main Parameters on the Mechanical and Wear Behaviour of Functionally Graded Materials by Centrifugal Casting: A Review

Bassiouny Saleh et al.

METALS AND MATERIALS INTERNATIONAL (2019)

Add to Collection

Article Engineering, Mechanical

Interaction between iron oxides and iron carbonates during running-in of C-steel tubings in CO2 corrosive environment

Manel Rodriguez Ripoll et al.

WEAR (2019)

Add to Collection

Article Chemistry, Physical

Silicon Carbide Ceramic Particulate Reinforced AA2024 Alloy Composite - Part I: Evaluation of Mechanical and Sliding Tribology Performance

Sourabh Bhaskar et al.

Silicon (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical and tribological analysis of functionally graded aluminium hybrid composite using RSM approach

Manu Sam et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Engineering, Mechanical

Evolution of nano-laminated structure formed by the thermally-assisted plastic deformation in dry sliding wear

Yun-Shuai Su et al.

TRIBOLOGY INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Effect of particle size on dry sliding wear behaviour of sillimanite reinforced aluminium matrix composites

Sandeep Sharma et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Engineering, Chemical

On the Modeling of Adhesive Wear with Consideration of Loading Sequence

K. P. Lijesh et al.

TRIBOLOGY LETTERS (2018)

Add to Collection

Review Materials Science, Ceramics

A review on laser deposition-additive manufacturing of ceramics and ceramic reinforced metal matrix composites

Yingbin Hu et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Tribocorrosion behaviour of aluminium bronze in 3.5 wt.% NaCl solution

E. Huttunen-Saarivirta et al.

CORROSION SCIENCE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Selective laser melting of TiC reinforced 316L stainless steel matrix nanocomposites: Influence of starting TiC particle size and volume content

Bandar AlMangour et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Engineering, Multidisciplinary

Microstructure, mechanical properties and corrosion behaviour of Al-Si-Mg alloy matrix/zircon and alumina hybrid composite

T. Satish Kumar et al.

FORSCHUNG IM INGENIEURWESEN-ENGINEERING RESEARCH (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics

Michael Oluwatosin Bodunrin et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2015)

Add to Collection

Review Materials Science, Multidisciplinary

Synthesis, microstructural and mechanical properties of ex situ zircon particles (ZrSiO4) reinforced Metal Matrix Composites (MMCs): a review

Satish Kumar Thandalam et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2015)

Add to Collection

Article Automation & Control Systems

The performance of pressure assisted casting process to improve the mechanical properties of Al-Si-Mg alloys matrix reinforced with coated B4C particles

Ali Mazahery et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Manufacture of Aluminium Metal Matrix Composite (Al7075-SiC) by Stir Casting Technique

V. Balaji et al.

MATERIALS TODAY-PROCEEDINGS (2015)

Add to Collection

Article Materials Science, Ceramics

Effect of carbon particle and carbon fiber on the microstructure and mechanical properties of short fiber reinforced reaction bonded silicon carbide composite

Shuang Li et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2013)

Add to Collection

Article Chemistry, Physical

AlB3 master alloy to grain refine AlSi10Mg and AlSi12Cu aluminium foundry alloys

Yucel Birol

JOURNAL OF ALLOYS AND COMPOUNDS (2012)

Add to Collection

Article Materials Science, Ceramics

Amorphous and crystalline phase formation during suspension plasma spraying of the alumina-zirconia composite

F. Tarasi et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2011)

Add to Collection

Article Chemistry, Physical

Processing and mechanical properties of B4C reinforced Al matrix composites

I. Topcu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2009)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effects of volume fraction of SiC particles on mechanical properties of SiC/Al composites

Song Min

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2009)

Add to Collection

Article Engineering, Mechanical

Tensile and wear behaviour of in situ Al-7Si/TiB2 particulate composites

S. Kumar et al.

WEAR (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion characteristics of hybrid Al/SiCp/MgAl2O4 composites fabricated with fly ash and recycled aluminum

R. Escalera-Lozano et al.

MATERIALS CHARACTERIZATION (2007)

Add to Collection

Article Materials Science, Coatings & Films

Correlation between structure and corrosion behaviour of nickel dispersion coatings containing ceramic particles of different sizes

Th. Lampke et al.

SURFACE & COATINGS TECHNOLOGY (2006)

Add to Collection

Article Materials Science, Composites

Limiting the development of Al4C3 to prevent degradation of Al/SiCP composites processed by pressureless infiltration

M Rodríguez-Reyes et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Thermal barrier coating materials

David R. Clarke et al.

MATERIALS TODAY (2005)

Add to Collection

Article Nanoscience & Nanotechnology

Formation of Al2Cu and AlCu intermetallics in Al(Cu) alloy matrix composites by reaction sintering

M Aravind et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)

Add to Collection

Article Engineering, Industrial

The formation of rosette α phase, structural evolution during the reheating and semi-solid casting of AlSi7Mg alloy

YZ Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

Article Crystallography

Thermal system design and dislocation reduction for growth of wide band gap crystals: application to SiC growth

RH Ma et al.

JOURNAL OF CRYSTAL GROWTH (2003)

Add to Collection

Article Engineering, Manufacturing

Mesostructure of WHIPOX all oxide CMCs

M Schmucker et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Role of grain-boundary precipitates and solute-depleted zone on the intergranular corrosion of aluminum alloy 7150

T Ramgopal et al.

CORROSION (2002)

Add to Collection

Article Materials Science, Multidisciplinary

The oxidation of SiC particles and its interfacial characteristics in Al-matrix composite

ZL Shi et al.

JOURNAL OF MATERIALS SCIENCE (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.