☆ 4.7 Article

Room-Temperature Ammonia Gas Sensor Based on Ti3C2Tx MXene/Graphene Oxide/CuO/ZnO Nanocomposite

ACS APPLIED NANO MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Layered Ti3C2Tx MXene/CuO spindles composites for NH3 detection at room-temperature

Miao Liu et al.

Summary: A multilayer Ti3C2Tx MXene/CuO composite was synthesized by a solvothermal method for room-temperature ammonia detection. The composite showed excellent sensitivity (46.7% towards 5 ppm NH3), ideal selectivity, short response time (12 s) and recovery time (25 s), and great long-term stability. This material is a promising candidate for high-performance room-temperature NH3 detection.

JOURNAL OF ALLOYS AND COMPOUNDS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

ZnO quantum dots decorated carbon nanotubes-based sensors for methanol detection at room temperature

Yotsarayuth Seekaew et al.

Summary: A highly sensitive methanol gas sensor at room temperature is developed by decorating ZnO quantum dots on carbon nanotubes via thermal vapor deposition and metal sparking technique. The ZnO quantum dots decorated carbon nanotubes show the highest response to methanol compared with other sparking times and undecorated materials, as well as high selectivity to methanol against other gases. The sensing mechanism of ZnO quantum dots decorated carbon nanotubes sensor is enhanced by the CNTs-ZnO QDs heterojunctions and quantum-size effects.

DIAMOND AND RELATED MATERIALS (2023)

Add to Collection

Article Agriculture, Multidisciplinary

Advances in gas sensors and electronic nose technologies for agricultural cycle applications

Thara Seesaard et al.

Summary: This review summarizes the utilization of gas sensors and E-nose technologies in agricultural best management practices, including cultivation preparation, crop production, harvesting, and storage. These technologies show great promise but also have limitations.

COMPUTERS AND ELECTRONICS IN AGRICULTURE (2022)

Add to Collection

Article Chemistry, Analytical

Selective room temperature ammonia gas sensor using nanostructured ZnO/CuO@graphene on paper substrate

Mohanraj Jagannathan et al.

Summary: The study successfully grew ZnO/CuO nanoflowers on graphene printed paper substrates for room temperature ammonia gas sensing. The fabricated substrate showed high sensing performance for low concentrations of ammonia, with quick response and recovery times. This method is effective for cost-effective and rapid detection of ammonia gas and potential for non-invasive early disease diagnosis.

SENSORS AND ACTUATORS B-CHEMICAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Nitrogen-doped carbon oxide quantum dots for flexible humidity sensor: Experimental and SCC-DFTB study

Sarawut Kondee et al.

Summary: A flexible resistive-type humidity sensor based on N-type nitrogen-doped carbon oxide quantum dots (NCQDs) exhibits high humidity response, good repeatability, and high stability. The study reveals the important role of N doping in the humidity sensing mechanism.

VACUUM (2022)

Add to Collection

Article Chemistry, Physical

Synergistically coupling of 3D FeNi-LDH arrays with Ti3C2Tx-MXene nanosheets toward superior symmetric supercapacitor

Renjie Zhang et al.

Summary: The study successfully enhances structural stability, electrical conductivity, and electrolyte-accessibility through the hierarchical nanohybridization of 3D FeNi-LDH arrays on 2D MXene nanosheets, significantly improving redox reaction kinetics and resulting in outstanding capacitance behavior and energy densities.

NANO ENERGY (2022)

Add to Collection

Article Engineering, Biomedical

Photoacoustic detection of ammonia exhaled by individuals with chronic kidney disease

Liana Genuncio Silva et al.

Summary: Ammonia (NH3) can be used as a breath biomarker for chronic kidney disease (CKD) with concentrations greater than 0.25 ppmV. Hemodialysis (HD) has been shown to significantly reduce ammonia levels in the breath of CKD patients.

LASERS IN MEDICAL SCIENCE (2022)

Add to Collection

Review Chemistry, Physical

Electrical sensing of volatile organic compounds in exhaled breath for disease diagnosis

Hailong Yan et al.

Summary: This article introduces the application of electrical sensors in breath volatolomics and focuses on the working principles of active nanomaterials and their impact on sensing performance. It highlights the capability of electrical sensors in noninvasive diagnosis and real-time monitoring, particularly for the analysis of important disease biomarkers. The opportunities and challenges in this field, particularly background interference and data recognition, are discussed as key factors in the development of prospective electrical sensors.

CURRENT OPINION IN ELECTROCHEMISTRY (2022)

Add to Collection

Article Engineering, Electrical & Electronic

Preparation and study of ammonia gas sensor based on ZnO/CuO heterojunction with high performance at room temperature

Cao Cheng et al.

Summary: An NH3 gas sensor based on ZnO/CuO heterojunctions was prepared using the hydrothermal method. The sensor exhibited excellent performance, including low detection limit, fast response/recovery time, high sensitivity, good selectivity, strong stability, and high humidity resistance at room temperature. The improved sensing performance is attributed to the presence of more oxygen free radicals and the strong adsorption energy of the ZnO/CuO heterojunctions. The strong built-in electric field of the heterojunctions enhances the polarity of NH3 molecules and induces a high response to NH3 molecules.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2022)

Add to Collection

Article Chemistry, Analytical

Mesoporous cellulose nanofibers-interlaced PEDOT:PSS hybrids for chemiresistive ammonia detection

Ruijie Zhang et al.

Summary: In this study, a composite sensor for room temperature ammonia detection was developed by incorporating cellulose nanofibers into PEDOT:PSS. The sensor exhibited high sensitivity, selectivity, and stability, with fast response and minimal baseline drift. Additionally, the sensor showed more than twofold response enhancement in the presence of humidity, and demonstrated flexible and bending-tolerant characteristics.

MICROCHIMICA ACTA (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Dual functions of alternating current electroluminescent device for light emission and humidity detection

Alisa Saengsonachai et al.

Summary: This paper presents a new design of AC-EL device with a silver oxide humidity-sensing layer for humidity detection. The AC-EL devices exhibited high response, good productivity, stability, and a linear relationship with humidity. The development of this device offers a simplified architecture for sensing functions.

NANOTECHNOLOGY (2022)

Add to Collection

Article Engineering, Environmental

Room temperature gas sensors based on Ce doped TiO2 nanocrystals for highly sensitive NH3 detection

Kaidi Wu et al.

Summary: This study developed a series of Ce doped TiO2 nanocrystals for ammonia detection at room temperature, showing high performance in terms of response, detection limit, selectivity, repeatability, and stability. The enhanced sensing mechanism was explained by the synergetic effects of re-orientated high energy facets, oxygen vacancy, and large specific surface area. Furthermore, the practical application potential in fish freshness detection was also evaluated.

CHEMICAL ENGINEERING JOURNAL (2022)

Add to Collection

Article Engineering, Environmental

Rotating triboelectric-electromagnetic nanogenerator driven by tires for self-powered MXene-based flexible wearable electronics

Dongyue Wang et al.

Summary: The development of flexible electronics has led to a demand for self-powered nanogenerators. In this study, a hybrid nanogenerator powered by tires was developed for gas and movement monitoring. The nanogenerator can power a light and charge a smartphone, and MXene/Ag-based sensors were fabricated for ethanol detection and joint activity monitoring.

CHEMICAL ENGINEERING JOURNAL (2022)

Add to Collection

Article Chemistry, Analytical

Gas sensing performance of carbon monoxide sensor based on rod-shaped tin diselenide/MOFs derived zinc oxide polyhedron at room temperature

Dongyue Wang et al.

Summary: This paper introduces a high-efficiency CO gas sensor based on ZnO/SnSe2 composite film, and studies its structural characteristics, response performance, and sensing mechanism. The study found that the ZnO/SnSe2 sensor with a loading rate of 25% SnSe2 showed the highest response performance, and UV light can improve the gas-sensing characteristics of the sensor.

SENSORS AND ACTUATORS B-CHEMICAL (2022)

Add to Collection

Article Chemistry, Physical

Multifunctional respiration-driven triboelectric nanogenerator for self-powered detection of formaldehyde in exhaled gas and respiratory behavior

Dongyue Wang et al.

Summary: A self-powered triboelectric nanogenerator has been developed for the detection of exhaled gas and disease diagnosis. The device exhibits excellent gas-sensing response and fast response/recovery time, and can identify different respiratory types.

NANO ENERGY (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Reduced Graphene Oxide Derived from Low-Grade Coal for High-Performance Flexible Supercapacitors with Ultrahigh Cyclability

Yi-Ming Wang et al.

Summary: Preparation of reduced graphene oxide (RGO) from low-grade coal shows promise for resource utilization. Large-size RGO sheets can be obtained through high temperature-high pressure (HTHP) pretreatment. The lignite-derived RGO exhibits high performance in supercapacitor applications.

NANOMATERIALS (2022)

Add to Collection

Review Biotechnology & Applied Microbiology

Recent Progress in Electronic Noses for Fermented Foods and Beverages Applications

Thara Seesaard et al.

Summary: This article provides a comprehensive review of the recent progress in electronic nose (E-nose) technologies for the analysis of fermented foods and beverages. E-nose technologies offer non-destructive measurement, fast analysis, low operating costs, and simplicity. The benefits, research directions, limitations, and challenges of current E-nose systems are investigated and highlighted for fermented food and beverage applications.

FERMENTATION-BASEL (2022)

Add to Collection

Article Biochemical Research Methods

Real-time breath ammonia measurement using a novel cuprous bromide sensor device in patients with chronic liver disease: a feasibility and pilot study

Jinya Ishida et al.

Summary: A small portable sensor device using a p-type semiconductor cuprous bromide (CuBr) thin film was developed to measure breath ammonia in real time, showing significant correlation with blood ammonia levels and liver cirrhosis.

JOURNAL OF BREATH RESEARCH (2021)

Add to Collection

Article Nanoscience & Nanotechnology

MXene Ti3C2Tx-Derived Nitrogen-Functionalized Heterophase TiO2 Homojunctions for Room-Temperature Trace Ammonia Gas Sensing

Yong Zhou et al.

Summary: In this study, nitrogen-functionalized heterophase TiO2 homojunctions (N-MXene) derived from MXene Ti3C2Tx were prepared and utilized as a sensing layer to detect trace NH3 gas at room temperature. The sensors exhibited improved detection limits and performance compared to existing MXene-involved reports, showing strong responses, sufficient recovery, and fast response/recovery speeds under humid conditions. The incorporation of nitrogen doping and TiO2 homojunctions played a key role in enhancing the performance of the sensors.

ACS APPLIED MATERIALS & INTERFACES (2021)

Add to Collection

Article Engineering, Electrical & Electronic

Partially oxidized Ti3C2Tx MXene-sensitive material-based ammonia gas sensor with high-sensing performances for room temperature application

Lijia Yao et al.

Summary: This paper develops a two-dimensional material, Ti3C2Tx MXene sensor, with high response and excellent selectivity to ammonia at room temperature, achieved through thermal treatment to improve electron transport efficiency. With good moisture resistance, the sensor has the potential to contribute to the development of future portable and selective sensing electronics at room temperature.

JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Multifunctional Latex/Polytetrafluoroethylene-Based Triboelectric Nanogenerator for Self-Powered Organ-like MXene/Metal-Organic Framework-Derived CuO Nanohybrid Ammonia Sensor

Dongyue Wang et al.

Summary: The paper introduces a self-powered sensor powered by a TENG for detecting ammonia at room temperature, showing excellent response and the potential to monitor pork quality. The sensor exhibits outstanding voltage and current performance, with great application prospects in wearable devices.

ACS NANO (2021)

Add to Collection

Article Engineering, Electrical & Electronic

3D printed CuO semiconducting gas sensor for ammonia detection at room temperature

Gun Chaloeipote et al.

Summary: A new room-temperature ammonia gas sensor based on n-type copper oxide was fabricated using 3D printing and sintering method. The sensor showed good repeatability, high stability, low humidity dependency, high sensitivity, and selectivity towards ammonia at room temperature. The sensing mechanism was proposed based on the resistance change via reaction on adsorbed surface oxygen species or direct electron transfer between ammonia molecules and CuO.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2021)

Add to Collection

Review Chemistry, Analytical

A Review on Functionalized Graphene Sensors for Detection of Ammonia

Xiaohui Tang et al.

Summary: Functionalized graphene gas sensors for NH3 detection at room temperature have shown great potential due to their high sensitivity, selectivity, and fast detection capability. Various materials, such as metallic nanoparticles, metal oxides, organic molecules, and conducting polymers, have been used to functionalize graphene gas sensors. Challenges in mass production and potential applications for graphene NH3 sensors are discussed along with proposed solutions.

SENSORS (2021)

Add to Collection

Article Chemistry, Analytical

Conductometric room temperature ammonia sensors based on titanium dioxide nanoparticles decorated thin black phosphorus nanosheets

Yanjie Wang et al.

Summary: The study utilized TiO2 nanoparticles decorated BP nanosheets as the sensing layer, achieving selective detection of 0.5-30 ppm NH3 at room temperature for the first time. The optimized BP-TiO2 sensors showed higher response, less baseline drift, shorter response/recovery times, and stronger long-term stability compared to pure BP counterparts.

SENSORS AND ACTUATORS B-CHEMICAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Fabrication of ZnO-MWCNT nanocomposite sensor and investigation of its ammonia gas sensing properties at room temperature

Leila Vatandoust et al.

Summary: Ammonia is a hazardous gas that plays a vital role in industry. A study on ZnO-MWCNT nanocomposite shows that it has a rough surface which increases the sensor's surface area and contact probability with gas. The sensor demonstrates higher and more stable sensitivity to NH3 compared to ZnO sensor, but low sensitivity to CH4 and CO.

SYNTHETIC METALS (2021)

Add to Collection

Review Chemistry, Analytical

Gas Sensors Based on Copper Oxide Nanomaterials: A Review

Stephan Steinhauer

Summary: Metal oxide semiconductors, particularly copper oxide nanomaterial-based devices, have been widely used in chemical sensors for detecting various gaseous analytes. Literature reports highly sensitive detection of target molecules including volatile organic compounds, hydrogen sulfide, carbon monoxide, carbon dioxide, hydrogen, and nitrogen oxide from parts-per-million down to parts-per-billion concentrations. Physico-chemical mechanisms for sensing and transduction are summarized, with prospects for future developments outlined.

CHEMOSENSORS (2021)

Add to Collection

Review Physics, Condensed Matter

Gas sensing materials roadmap

Huaping Wang et al.

Summary: Gas sensor technology is widely utilized in various fields and continuous efforts are made to improve selectivity, sensitivity, and power consumption. Research has focused on the sensing layer, with emerging materials like nanocomposites and two-dimensional materials gaining interest. This roadmap aims to discuss the current status, progress, and challenges in gas sensing materials for future applications.

JOURNAL OF PHYSICS-CONDENSED MATTER (2021)

Add to Collection

Review Chemistry, Physical

Electrochemical biosensors based on Ti3C2Tx MXene: future perspectives for on-site analysis

Minu Mathew et al.

Summary: MXenes, as newly developed two-dimensional layered materials, show great potential in electrochemical biosensor applications. With their multilayered configuration and high conductivity, they can serve as immobilization matrices for biomolecules and contribute to the fabrication of advanced electrochemical biosensors with high sensitivity and selectivity.

CURRENT OPINION IN ELECTROCHEMISTRY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Metal-Ion-Intercalated MXene Nanosheet Films for NH3 Gas Detection

Soobin Kim et al.

Summary: MXenes are promising materials for functional transparent thin films due to their high conductivity, transparency, and two-dimensional morphology. Intercalation of metal ions into MXene films through a spontaneous self-assembly method enhances film properties and device performance, with potential applications in gas sensing.

ACS APPLIED NANO MATERIALS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Copper Oxide Nanorod/Reduced Graphene Oxide Composites for NH3 Sensing

Muthu Mariappan Sivalingam et al.

Summary: The study investigates the NH3 sensing performance of CuO:rGO composites prepared using different chemical routes, revealing that the improved sensor response of hydrothermally synthesized CuO:rGO is primarily attributed to the higher concentration of active sites induced on the CuO nanorod surface by rGO.This enhanced response is also facilitated by the favorable band bending at the rGO-CuO interface.

ACS APPLIED NANO MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

An efficient amperometric catechol sensor based on novel polypyrrole-carbon black doped α-Fe2O3 nanocomposite

Jahir Ahmed et al.

Summary: A highly sensitive and selective electrochemical catechol sensor based on a novel nanocomposite-modified electrode has been developed and demonstrated. The sensor shows excellent reproducibility, repeatability, and long-term stability in detecting catechol levels in real samples, making it an effective technique for environmental safety.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)

Add to Collection

Article Chemistry, Physical

Electrochemical sensor for detection of tryptophan in the milk sample based on MnWO4 nanoplates encapsulated RGO nanocomposite

Ruspika Sundaresan et al.

Summary: Tryptophan, an essential amino acid associated with neurotransmitters and specific syndromes, is often detected using electrochemical sensors due to their sensitivity and efficiency. Bimetal oxides combined with reduced graphene oxide have shown promising results in the trace-level detection of amino acids, providing a rapid and selective method for determination.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)

Add to Collection

Article Chemistry, Physical

Enhanced ammonia sensing performance based on MXene-Ti3C2Tx multilayer nanoflakes functionalized by tungsten trioxide nanoparticles

Xuezheng Guo et al.

Summary: A Ti3C2Tx/WO3 composite resistive sensor is developed with high sensitivity for NH3 detection at room temperature, showing a sensitivity 15.4 times higher than pure Ti3C2Tx sensor. The composite sensor exhibits excellent reproducibility, good long-term stability, and high selectivity to NH3, and the influence of relative humidity on NH3 gas sensing properties of the sensors is systematically studied.

JOURNAL OF COLLOID AND INTERFACE SCIENCE (2021)

Add to Collection

Review Chemistry, Analytical

Progress in ZnO Nanosensors

Miaoling Que et al.

Summary: Developing various nanosensors with superior performance is crucial for accurate and sensitive detection of physical signals in electronic systems. Zinc oxide (ZnO) has unique semiconductor properties that have led to extensive research on its use as high-performance sensors. This review introduces the morphology and synthetic methods of ZnO nanomaterials, discusses their advantages and weaknesses, and focuses on recent progress in functional classification of ZnO nanosensors.

SENSORS (2021)

Add to Collection

Article Chemistry, Analytical

Flexible MXene/rGO/CuO hybrid aerogels for high performance acetone sensing at room temperature

Miao Liu et al.

Summary: In this study, a high-performance room temperature gas-sensing material was successfully developed by utilizing MXene and reduced graphene oxide as building blocks. The resulting 3D aerogel shows excellent acetone-sensing performance at room temperature, with fast response and recovery times, as well as good reproducibility and selectivity. This strategy of composite 3D graphene/MXene architectures with metal oxide semiconductors provides a new pathway for future development of room temperature gas sensors.

SENSORS AND ACTUATORS B-CHEMICAL (2021)

Add to Collection

Article Multidisciplinary Sciences

High-performance resistive humidity sensor based on Ag nanoparticles decorated with graphene quantum dots

Gun Chaloeipote et al.

Summary: In this study, a low-cost, fast and simple resistive-type humidity sensor based on graphene quantum dots and silver nanoparticles was developed, showing excellent humidity response and fast response/recovery times. The sensing mechanism involves the formation of Schottky junction and intrinsic synergistic effects between GQDs and AgNPs.

ROYAL SOCIETY OPEN SCIENCE (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Enhanced Blocking Effect: A New Strategy to Improve the NO2 Sensing Performance of Ti3C2Tx by γ-Poly(L-glutamic acid) Modification

Qiuni Zhao et al.

Summary: The study demonstrates the enhancement of gas sensing properties of Ti3C2Tx by gamma-PGA modification, resulting in improved response to NO2, faster response/recovery time, better reversibility, and repeatability. The improved gas sensing properties of the Ti3C2Tx/gamma-PGA sensor can be attributed to the enhancement of effective adsorption and the blocking effect assisted by water molecules.

ACS SENSORS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

MOF-Derived Porous Hollow Co3O4@ZnO Cages for High-Performance MEMS Trimethylamine Sensors

Wenjun Yan et al.

Summary: A Co3O4@ZnO sensor with excellent TMA sensing performance and high sensitivity was designed and fabricated, utilizing a porous hollow structure and maximizing heterojunctions for enhanced gas sensing capabilities.

ACS SENSORS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Exploiting Free-Standing p-CuO/n-TiO2 Nanochannels as a Flexible Gas Sensor with High Sensitivity for H2S at Room Temperature

Haoxuan He et al.

Summary: A flexible H2S gas-sensing device operated at room temperature based on CuO/TiO2 membranes showed notable detection sensitivity and durability. The innovative design paves the way for sensitive gas sensing on a universal platform.

ACS SENSORS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Room-Temperature, Highly Durable Ti3C2Tx MXene/Graphene Hybrid Fibers for NH3 Gas Sensing

Sang Hoon Lee et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Hydroxyl edge-functionalized graphene quantum dots for gas-sensing applications

Sarun Arunragsa et al.

DIAMOND AND RELATED MATERIALS (2020)

Add to Collection

Article Thermodynamics

Sandwich-like silicon/Ti3C2Tx MXene composite by electrostatic self-assembly for high performance lithium ion battery

Fan Zhang et al.

ENERGY (2020)

Add to Collection

Article Chemistry, Analytical

W18O49/Ti3C2Tx Mxene nanocomposites for highly sensitive acetone gas sensor with low detection limit

Shibin Sun et al.

SENSORS AND ACTUATORS B-CHEMICAL (2020)

Add to Collection

Article Chemistry, Multidisciplinary

In Situ Formation of Multiple Schottky Barriers in a Ti3C2MXene Film and its Application in Highly Sensitive Gas Sensors

Junghoon Choi et al.

ADVANCED FUNCTIONAL MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Anti-biofouling NH3 gas sensor based on reentrant thorny ZnO/graphene hybrid nanowalls

Tian Hang et al.

MICROSYSTEMS & NANOENGINEERING (2020)

Add to Collection

Article Chemistry, Analytical

Facile fabrication of PANI/Zn-tpps4 flexible NH3 sensor based on the bridge of Zn-tpps4

Shaoyong Cai et al.

SENSORS AND ACTUATORS B-CHEMICAL (2020)

Add to Collection

Article Chemistry, Physical

Rice Crust-Like ZnO/Ti3C2Tx MXene Hybrid Structures for Improved Photocatalytic Activity

Qui Thanh Hoai Ta et al.

CATALYSTS (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Ammonia Gas Sensor Response of a Vertical Zinc Oxide Nanorod-Gold Junction Diode at Room Temperature

Ying Tu et al.

ACS SENSORS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Polymeric Ti3C2Tx MXene Composites for Room Temperature Ammonia Sensing

Ling Jin et al.

ACS APPLIED NANO MATERIALS (2020)

Add to Collection

Article Biochemistry & Molecular Biology

Breath Ammonia Is a Useful Biomarker Predicting Kidney Function in Chronic Kidney Disease Patients

Ming-Jen Chan et al.

BIOMEDICINES (2020)

Add to Collection

Article Nanoscience & Nanotechnology

MoSe2 Crystalline Nanosheets for Room-Temperature Ammonia Sensing

Sukhwinder Singh et al.

ACS APPLIED NANO MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

CuO Nanoparticles/Ti3C2Tx MXene Hybrid Nanocomposites for Detection of Toluene Gas

Angga Hermawan et al.

ACS APPLIED NANO MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Graphene Oxide-Loaded SnO2 Quantum Wires with Sub-4 Nanometer Diameters for Low-Temperature H2S Gas Sensing

Zhilong Song et al.

ACS APPLIED NANO MATERIALS (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Improvement of Gas and Humidity Sensing Properties of Organ-like MXene by Alkaline Treatment

Zijie Yang et al.

ACS SENSORS (2019)

Add to Collection

Article Chemistry, Inorganic & Nuclear

One-step hydrothermal synthesis of fluorescent MXene-like titanium Chock for carbonitride quantum dots

Wenhan Kong et al.

INORGANIC CHEMISTRY COMMUNICATIONS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of annealing time on the structural and optical properties of n-CuO thin films deposited by sol-gel spin coating technique and its application in n-CuO/p-Si heterojunction diode

Richa Singh et al.

THIN SOLID FILMS (2019)

Add to Collection

Article Chemistry, Physical

Flexible self-powered high-performance ammonia sensor based on Au-decorated MoSe2 nanoflowers driven by single layer MoS2-flake piezoelectric nanogenerator

Dongzhi Zhang et al.

NANO ENERGY (2019)

Add to Collection

Article Chemistry, Physical

Adsorption of the NH3, NO, NO2, CO2, and CO gas molecules on blue phosphorene: A first-principles study

F. Safari et al.

APPLIED SURFACE SCIENCE (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Ti3C2 MXene-Based Sensors with High Selectivity for NH3 Detection at Room Temperature

Meng Wu et al.

ACS SENSORS (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Ultrahigh Selective Room-Temperature Ammonia Gas Sensor Based on Tin-Titanium Dioxide/reduced Graphene/Carbon Nanotube Nanocomposites by the Solvothermal Method

Yotsarayuth Seekaew et al.

ACS OMEGA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Ti3C2Tx MXene characterization produced from SHS-ground Ti3AlC2

Anna Pazniak et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Metallic Ti3C2TX MXene Gas Sensors with Ultrahigh Signal-to-Noise Ratio

Seon Joon Kim et al.

ACS NANO (2018)

Add to Collection

Article Chemistry, Analytical

Hydrothermal preparation of CoO/Ti3C2 composite material for lithium-ion batteries with enhanced electrochemical performance

Xuelin Li et al.

JOURNAL OF ELECTROANALYTICAL CHEMISTRY (2018)

Add to Collection

Article Chemistry, Physical

Synthesis of the 0D/3D CuO/ZnO Heterojunction with Enhanced Photocatalytic Activity

Linyu Zhu et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2018)

Add to Collection

Article Physics, Condensed Matter

Characterization of the microstructure and the optical and electrical properties of the direct-current magnetron sputtered CuO films at different substrate temperatures

Yongli Du et al.

PHYSICA B-CONDENSED MATTER (2018)

Add to Collection

Article Chemistry, Analytical

GO/Cu2O nanocomposite based QCM gas sensor for trimethylamine detection under low concentrations

Wei Chen et al.

SENSORS AND ACTUATORS B-CHEMICAL (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Lattice defects of ZnO and hybrids with GO: Characterization, EPR and optoelectronic properties

Gulzar Ahmed et al.

AIP ADVANCES (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Surface modification of micro-sized CuO by in situ-growing heterojunctions CuO/Cu2O and CuO/Cu2O/Cu: effect on surface charges and photogenerated carrier lifetime

Xi Mo et al.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2018)

Add to Collection

Article Chemistry, Analytical

Excellent room temperature ammonia gas sensing properties of n MoS2/P-CuO heterojunction nanoworms

Shubham Sharma et al.

SENSORS AND ACTUATORS B-CHEMICAL (2018)

Add to Collection

Article Chemistry, Physical

A flexible VOCs sensor based on a 3D Mxene framework with a high sensing performance

Wenjing Yuan et al.

JOURNAL OF MATERIALS CHEMISTRY A (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Polyaniline Anchored MWCNTs on Fabric for High Performance Wearable Ammonia Sensor

Debasis Maity et al.

ACS SENSORS (2018)

Add to Collection

Article Chemistry, Physical

Ti3C2Tx ( T 1/4 F, OH) MXene nanosheets: conductive 2D catalysts for ambient electrohydrogenation of N2 to NH3+

Jinxiu Zhao et al.

JOURNAL OF MATERIALS CHEMISTRY A (2018)

Add to Collection

Article Chemistry, Physical

Advanced analysis of copper X-ray photoelectron spectra

Mark C. Biesinger

SURFACE AND INTERFACE ANALYSIS (2017)

Add to Collection

Article Multidisciplinary Sciences

Room-temperature NH3 sensing of graphene oxide film and its enhanced response on the laser-textured silicon

Suwan Zhu et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Chemistry, Physical

MXene/graphene hybrid fibers for high performance flexible supercapacitors

Qiuyan Yang et al.

JOURNAL OF MATERIALS CHEMISTRY A (2017)

Add to Collection

Review Nanoscience & Nanotechnology

2D metal carbides and nitrides (MXenes) for energy storage

Babak Anasori et al.

NATURE REVIEWS MATERIALS (2017)

Add to Collection

Article Multidisciplinary Sciences

Sonochemical Synthesis of Sulfur Doped Reduced Graphene Oxide Supported CuS Nanoparticles for the Non-Enzymatic Glucose Sensor Applications

Natarajan Karikalan et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Room Temperature Gas Sensing of Two-Dimensional Titanium Carbide (MXene)

Eunji Lee et al.

ACS APPLIED MATERIALS & INTERFACES (2017)

Add to Collection

Article Chemistry, Multidisciplinary

Template-free 3D titanium carbide (Ti3C2Tx) MXene particles crumpled by capillary forces

S. A. Shah et al.

CHEMICAL COMMUNICATIONS (2017)

Add to Collection

Review Environmental Sciences

Catalytic oxidation of volatile organic compounds (VOCs) - A review

Muhammad Shahzad Kamal et al.

ATMOSPHERIC ENVIRONMENT (2016)

Add to Collection

Article Chemistry, Physical

Sensing of NH3 on heterogeneous nanoporous carbons in the presence of humidity

Nikolina A. Travlou et al.

CARBON (2016)

Add to Collection

Article Nanoscience & Nanotechnology

ZnO Nanoparticles/Reduced Graphene Oxide Bilayer Thin Films for Improved NH3-Sensing Performances at Room Temperature

Huiling Tai et al.

NANOSCALE RESEARCH LETTERS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of grain boundaries and interfaces on the electronic structure of polycrystalline CuO thin films

Jan Morasch et al.

PHYSICA STATUS SOLIDI A-APPLICATIONS AND MATERIALS SCIENCE (2016)

Add to Collection

Article Chemistry, Multidisciplinary

A highly sensitive gas sensor based on CuO nanoparticles synthetized via a sol-gel method

Fang Wang et al.

RSC ADVANCES (2016)

Add to Collection

Article Nanoscience & Nanotechnology

ZnO Nanoparticles/Reduced Graphene Oxide Bilayer Thin Films for Improved NH3-Sensing Performances at Room Temperature

Huiling Tai et al.

NANOSCALE RESEARCH LETTERS (2016)

Add to Collection

Article Multidisciplinary Sciences

Multi-functional reactively-sputtered copper oxide electrodes for supercapacitor and electro-catalyst in direct methanol fuel cell applications

Sambhaji M. Pawar et al.

SCIENTIFIC REPORTS (2016)

Add to Collection

Article Chemistry, Physical

Remarkable Conversion Between n- and p-Type Reduced Graphene Oxide on Varying the Thermal Annealing Temperature

Nguyen Dien Kha Tu et al.

CHEMISTRY OF MATERIALS (2015)

Add to Collection

Article Chemistry, Analytical

Characteristics of ZnO nanorods-based ammonia gas sensors with a cross-linked configuration

Tai-You Chen et al.

SENSORS AND ACTUATORS B-CHEMICAL (2015)

Add to Collection

Article Chemistry, Physical

Synthesis of porous Cu2O/CuO cages using Cu-based metal-organic frameworks as templates and their gas-sensing properties

Yiting Wang et al.

JOURNAL OF MATERIALS CHEMISTRY A (2015)

Add to Collection

Article Chemistry, Physical

Simultaneous glucose sensing and biohydrogen evolution from direct photoelectrocatalytic glucose oxidation on robust Cu2O-TiO2 electrodes

Anitha Devadoss et al.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Low-cost and flexible printed graphene-PEDOT:PSS gas sensor for ammonia detection

Yotsarayuth Seekaew et al.

ORGANIC ELECTRONICS (2014)

Add to Collection

Article Chemistry, Analytical

Reverse microemulsion in situ crystallizing growth of ZnO nanorods and application for NO2 sensor

Shouli Bai et al.

SENSORS AND ACTUATORS B-CHEMICAL (2014)

Add to Collection

Article Chemistry, Analytical

Highly sensitive large-area multi-layered graphene-based flexible ammonia sensor

Ruma Ghosh et al.

SENSORS AND ACTUATORS B-CHEMICAL (2014)

Add to Collection

Article Chemistry, Multidisciplinary

Electronic nose for toxic gas detection based on photostimulated core-shell nanowires

Chatchawal Wongchoosuk et al.

RSC ADVANCES (2014)

Add to Collection

Article Multidisciplinary Sciences

Single Junction Inverted Polymer Solar Cell Reaching Power Conversion Efficiency 10.31% by Employing Dual-Doped Zinc Oxide Nano-Film as Cathode Interlayer

Sih-Hao Liao et al.

SCIENTIFIC REPORTS (2014)

Add to Collection

Article Engineering, Environmental

Ammonia adsorption on graphene and graphene oxide: a first-principles study

Yue Peng et al.

FRONTIERS OF ENVIRONMENTAL SCIENCE & ENGINEERING (2013)

Add to Collection

Article Chemistry, Physical

Adsorption of gas molecules on graphene nanoribbons and its implication for nanoscale molecule sensor

Bing Huang et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2008)

Add to Collection

Article Gastroenterology & Hepatology

Breath ammonia measurement in Helicobacter pylori infection

DJ Kearney et al.

DIGESTIVE DISEASES AND SCIENCES (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.