4.7 Article

In situ U-value measurement of building envelopes through continuous low-cost monitoring

Related references

Note: Only part of the references are listed.
Article Green & Sustainable Science & Technology

Comparison between Heat Flow Meter (HFM) and Thermometric (THM) Method for Building Wall Thermal Characterization: Latest Advances and Critical Review

Luca Evangelisti et al.

Summary: This paper discusses two experimental techniques for measuring the thermal performance of buildings: heat flow meter and thermometric methods. By analyzing scientific papers, an overview of the latest advances in these techniques is provided, along with detailed descriptions of basic theory, measurement equipment, and data processing methods.

SUSTAINABILITY (2022)

Article Chemistry, Multidisciplinary

Smart Tags: IoT Sensors for Monitoring the Micro-Climate of Cultural Heritage Monuments

Nikos Mitro et al.

Summary: The building materials of Cultural Heritage monuments are prone to degradation due to harsh weather conditions caused by Climate Change. To address this issue, the HYPERION project has developed a distributed smart sensor network to provide environmental measurements and assist in studying and mitigating the deterioration.

APPLIED SCIENCES-BASEL (2022)

Article Construction & Building Technology

Non-destructive techniques (NDT) for the diagnosis of heritage buildings: Traditional procedures and futures perspectives

Blanca Tejedor et al.

Summary: This study aimed to evaluate the applicability of non-destructive techniques and advanced modeling technologies for the diagnosis of heritage buildings. Through bibliometric analysis of relevant research, it was found that most studies were conducted in Southern European countries. Photogrammetry and laser applications were identified as mature techniques for historic preservation, but there is a significant gap in the area of quantitative NDT. Future research should propose a common diagnosis protocol.

ENERGY AND BUILDINGS (2022)

Article Thermodynamics

Selection of retrofit measures for reasonable energy and hygrothermal performances of modern heritage building under dry cold and hot humid climate:A case of modern heritage school in Korea

Yena Chae et al.

Summary: This study demonstrates how to improve energy performance of heritage buildings while preserving their historical value through a case study. The measures include improving insulation and airtightness, replacing air-conditioning systems, using independent ventilation or dehumidifiers, and air-conditioning public areas and unoccupied spaces. When heritage buildings are vulnerable, 24/7 mechanical climate controls can be chosen, but thermal bridging should be taken into consideration to prevent material degradation.

CASE STUDIES IN THERMAL ENGINEERING (2022)

Article Thermodynamics

Dynamic thermal bridge evaluation of window-wall joints using a model-based thermography method

Jae-Sol Choi et al.

Summary: In this study, a digital twin-based method was proposed to diagnose thermal bridges in buildings using infrared thermography. By describing the structure with a numerical model, insulation defects and thermal bridges at the window-wall joint can be accurately identified. It was found that by changing the thermal conductivity of the joint, the temperature difference can be reduced, resulting in improved accuracy and calculation efficiency of the simulation model.

CASE STUDIES IN THERMAL ENGINEERING (2022)

Article Thermodynamics

Protective energy-saving retrofits of rammed earth heritage buildings using multi-objective optimization

Wei Jiang et al.

Summary: This study validates and optimizes the protective energy-saving retrofitting measures for heritage buildings through multi-objective optimization and building information modelling. The results indicate that adding internal thermal insulation and replacing exterior windows can significantly reduce energy consumption and greenhouse gas emissions. The optimal solution involves the use of expanded polystyrene insulation and polyurethane windows.

CASE STUDIES IN THERMAL ENGINEERING (2022)

Article Construction & Building Technology

Application of Low-Cost Sensors for Accurate Ambient Temperature Monitoring

Behnam Mobaraki et al.

Summary: A novel monitoring system is proposed for accurate measurement of indoor temperature in buildings. By using multiple low-cost sensors, multiple measurements of ambient temperatures can be obtained, and statistical analysis shows that increasing the number of sensors reduces the discrepancy in measurements.

BUILDINGS (2022)

Article Construction & Building Technology

A Novel Data Acquisition System for Obtaining Thermal Parameters of Building Envelopes

Behnam Mobaraki et al.

Summary: A novel hyper-efficient Arduino transmittance-meter was introduced to overcome limitations in appraising the thermal performance of building envelopes. The experimental results showed a high level of cost reduction and a low range of difference compared with a commercial device, validating the applicability of the proposed thermal monitoring system.

BUILDINGS (2022)

Article Construction & Building Technology

An IoT-based deep learning approach to analyse indoor thermal comfort of disabled people

Bouziane Brik et al.

Summary: Monitoring the thermal comfort of building occupants is crucial, with few studies considering the unique requirements of disabled individuals, who may have difficulty expressing their comfort levels. The proposed deep learning model shows high accuracy in predicting thermal comfort in real time for differently abled people, demonstrating the potential for remote monitoring and efficient data collection.

BUILDING AND ENVIRONMENT (2021)

Article Thermodynamics

Numerical simulation of the effect of bamboo composite building envelope on summer overheating problem

Layth S. Al-Rukaibawi et al.

Summary: Bamboo is a sustainable building material that grows rapidly, retains thermal and mechanical properties similar to wood, and is effective at absorbing CO2. A numerical study compared the overheating and thermal comfort of different building envelopes, with the original steel-bamboo showing the best performance in hot weather, while other systems experienced overheating during summer due to lack of shading and ventilation.

CASE STUDIES IN THERMAL ENGINEERING (2021)

Review Construction & Building Technology

Application of Low-Cost Sensors for Building Monitoring: A Systematic Literature Review

Behnam Mobaraki et al.

Summary: This article presents a systematic review of the state of the art in low-cost sensors technology in building monitoring, illustrating their potential uses and addressing key parameters and communication protocols in building monitoring. The article emphasizes on the deficiencies in current studies and proposes parameters for future research in building monitoring.

BUILDINGS (2021)

Article Construction & Building Technology

A methodological approach for heat-flow meter data post-processing under different climatic conditions and wall orientations

Luca Evangelisti et al.

ENERGY AND BUILDINGS (2020)

Review Green & Sustainable Science & Technology

Review of in situ methods for assessing the thermal transmittance of walls

David Bienvenido-Huertas et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2019)

Article Construction & Building Technology

An applied framework to evaluate the impact of indoor office environmental factors on occupants' comfort and working conditions

Maedot S. Andargie et al.

SUSTAINABLE CITIES AND SOCIETY (2019)

Article Construction & Building Technology

A comparison of standardized calculation methods for in situ measurements of facades U-value

Katia Gaspar et al.

ENERGY AND BUILDINGS (2016)

Article Construction & Building Technology

In situ measurement of thermal transmittance and thermal resistance of hollow reinforced precast concrete walls

Aftab Ahmad et al.

ENERGY AND BUILDINGS (2014)

Article Construction & Building Technology

A measuring campaign of thermal conductance in situ and possible impacts on net energy demand in buildings

Pier Giorgio Cesaratto et al.

ENERGY AND BUILDINGS (2013)