☆ 4.7 Article

Investigation on hardness, impact, and compression responses of additively manufactured functionally graded nanocomposites

COMPOSITES COMMUNICATIONS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Quasi-static compressive behavior of bioactive glass reinforced high density polyethylene composites

Praveen Jeyachandran et al.

Summary: This study investigates the compressive behavior of additively manufactured bioactive glass reinforced high density polyethylene composites under quasi static conditions. Results show that elastic modulus and yield strength increase with filler addition and strain rate, while energy absorption is proportional to strain rate and BAG content.

MATERIALS LETTERS (2022)

Add to Collection

Article Materials Science, Composites

MEX 3D Printed HDPE/TiO2 Nanocomposites Physical and Mechanical Properties Investigation

Nectarios Vidakis et al.

Summary: This research aims to develop more robust and mechanically advanced Fused Filament Fabrication (FFF) materials by incorporating Titanium Dioxide (TiO2) filler into High-Density Polyethylene (HDPE) matrix. The results indicate that the filler can significantly improve the mechanical strength of HDPE at certain concentrations.

JOURNAL OF COMPOSITES SCIENCE (2022)

Add to Collection

Article Materials Science, Characterization & Testing

Mechanical characterization of 3D printed MWCNTs/ HDPE nanocomposites

Sumodh Kumar et al.

Summary: This paper presents the development of polymer nanocomposite blends using multi-walled carbon nanotubes and highdensity polyethylene. The thermal stability and mechanical properties of the nanocomposite were tested, showing that the addition of carbon nanotubes improves the decomposition temperature and strength.

POLYMER TESTING (2022)

Add to Collection

Article Materials Science, Composites

Compressive behavior of 3D printed MWCNT/HDPE nanocomposites

Sumodh Kumar et al.

Summary: This study investigates the compressive behavior of three-dimensional printed functionalized multi-walled carbon nanotubes/high-density polyethylene nanocomposite samples. The research finds that the compressive performance of the printed materials improves with increasing loading of functionalized carbon nanotubes, but the energy absorption capacity decreases.

COMPOSITES COMMUNICATIONS (2022)

Add to Collection

Article Materials Science, Composites

The Impact of Zinc Oxide Micro-Powder Filler on the Physical and Mechanical Response of High-Density Polyethylene Composites in Material Extrusion 3D Printing

Nectarios Vidakis et al.

Summary: This study aimed to develop novel polymer composites using melt extrusion and 3D printing, incorporating zinc oxide particles in various weight percentages. The mechanical properties of the composites were evaluated and it was found that the filler increased the strength of pure HDPE, with a maximum increase of 54.6% in flexural strength and 53.8% in tensile strength. Scanning Electron Microscopy, Raman, and thermal characterization techniques were used to analyze the samples, and the experimental findings were applicable in other research areas.

JOURNAL OF COMPOSITES SCIENCE (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Wear performance and mechanical properties of MWCNT/HDPE nanocomposites for gearing applications

Sameh Dabees et al.

Summary: The study prepared potential gear materials with enhanced hardness, tensile properties, and wear resistance using nanocomposites. Nanofillers improved the mechanical properties and thermal stability of the composites within a certain concentration range, but could lead to increased brittleness at higher concentrations.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Mechanics

Dynamic behavior of concurrently printed functionally graded closed cell foams

Bonthu Dileep et al.

Summary: Functionally graded closed cell foams reinforced with hollow glass microballoons were 3D printed and evaluated for mechanical buckling and free vibration response. FGF-2 showed higher buckling strength and better natural frequency performance compared to other FGFs. Experimental results were validated with finite element simulation results.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Mechanics

Wave propagation analysis of a ceramic-metal functionally graded sandwich plate with different porosity distributions in a hygro-thermal environment

Saeed Tahir et al.

Summary: This paper presents the wave propagation analysis of porous functionally graded sandwich plates in a hygro-thermal environment using a simple four-unknown integral higher-order shear deformation theory. It investigates the effects of moisture and temperature on wave propagation by considering their role on materials' expansion, and discusses the impact of various factors through numerical results. The findings can serve as a benchmark for further studies on wave propagation in functionally graded plates.

COMPOSITE STRUCTURES (2021)

Add to Collection

Review Mechanics

Mechanical behavior of 3D printed syntactic foam composites

H. S. Bharath et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Mechanics

Mechanical behavior of additively manufactured nanoclay/HDPE nanocomposites

Pavan Beesetty et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Chemistry, Multidisciplinary

Three-Dimensional Printed Lightweight Composite Foams

H. S. Bharath et al.

ACS OMEGA (2020)

Add to Collection

Article Materials Science, Composites

Eco-friendly lightweight filament synthesis and mechanical characterization of additively manufactured closed cell foams

Balu Patil et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Composites

Mechanical and thermo-mechanical peculiarity of functionally graded materials-based glass fiber-filled polybutylene terephthalate composites

Akant K. Singh et al.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2018)

Add to Collection

Article Engineering, Multidisciplinary

Development of glass microballoon/HDPE syntactic foams by compression molding

M. L. Jayavardhan et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Engineering, Multidisciplinary

Mechanical behavior of polylactic acid/polycaprolactone porous layered functional composites

Roberto Scaffaro et al.

COMPOSITES PART B-ENGINEERING (2016)

Add to Collection

Article Engineering, Multidisciplinary

The use of polyethylene copolymers as compatibilizers in carbon fiber reinforced high density polyethylene composites

Lemiye Atabek Savas et al.

COMPOSITES PART B-ENGINEERING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Processing of cenosphere/HDPE syntactic foams using an industrial scale polymer injection molding machine

B. R. Bharath Kumar et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Ceramics

Effect of angled indentation on mechanical properties

Saeed Saber-Samandari et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2009)

Add to Collection

Article Materials Science, Composites

Mechanical properties of high density polyethylene/carbon nanotube composites

S. Kanagaraj et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2007)

Add to Collection

© Peeref 2019-2024. All rights reserved.