Related references
Note: Only part of the references are listed.
Article
Materials Science, Multidisciplinary
Xiaojing Fu et al.
Summary: In this study, TiN coatings were deposited on the surface of AISI 304 stainless steel by DC magnetron sputtering. The structural characteristics of the coatings were modulated by varying the nitrogen flux ratio during deposition. The results showed that the nitrogen flux ratio had a significant impact on the microstructure and mechanical and tribological properties of the TiN coatings. The coating deposited at a nitrogen flux ratio of 0.45 exhibited the best mechanical properties and tribological performance among the four coatings.
Article
Materials Science, Multidisciplinary
He Tao et al.
Summary: The mechanical properties and corrosion resistance of Cr-CrN, Ti-TiN, Zr-ZrN, and Mo-MoN coatings deposited on Ti-6Al-4V alloy were compared. The phase composition, hardness, and fracture resistance of the coatings were determined, and their structural characteristics were analyzed using microscopy techniques. The friction coefficient and corrosion resistance of the coatings were investigated at different temperatures and in a 3% NaCl solution. The results showed that the Zr-ZrN coating exhibited the lowest friction coefficient and the best corrosion resistance.
Article
Materials Science, Multidisciplinary
Peter Panjan et al.
Summary: This paper presents a comparative study of the tribological properties of TiN coatings prepared by different methods. The influence of coating properties, friction conditions, surface topography, and surrounding atmosphere on the tribological behavior was analyzed. The study focused on the initial phase of sliding tests and found significant differences in the tribological response of the coatings. The presence of nodular defects and metal droplets on the coating surface were found to affect the tribological behavior. The wear rates were found to increase with surface roughness, with coatings prepared by cathodic arc deposition showing the highest wear rates. The influence of post-polishing and the surrounding atmosphere, such as ambient air, oxygen, and nitrogen, was also investigated. The wear rate was found to be lower in ambient air compared to oxygen atmosphere, possibly due to the influence of humidity. The wear rates measured in a nitrogen atmosphere were much lower than those measured in an oxygen or ambient air atmosphere.
Article
Materials Science, Multidisciplinary
Haiyang Li et al.
Summary: This study investigates the wear characteristics of the spindle hook teeth of cotton pickers in different working areas. The results show that there are differences in the composition and hardness of the coating and substrate of the hook teeth. The wear starts from the tooth tips and gradually extends to the tooth edge and surrounding areas.
Article
Materials Science, Multidisciplinary
Qiankun Zhang et al.
Summary: The study revealed that the chrome plating layer on the surface of the hydraulic jack piston rod had pores and penetrating cracks, leading to intensified corrosion and eventual peeling. More oxygen and trace amounts of sulfur were detected in the corrosion pit. The peeling was primarily caused by pores, microcracks, working medium, and poor working environment.
Article
Engineering, Mechanical
Youqiang Zhang et al.
Summary: By studying the wear mechanisms and processes of spindles, design and production of more wear-resistant spindles can be achieved, improving the lifespan and efficiency of cotton picking machinery.
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME
(2021)
Article
Engineering, Mechanical
Vivek Kumar et al.
Summary: Surface roughness is inherent to machining processes and can significantly affect bearing performance. Surface texturing is a new technique to improve tribological behavior of mating surfaces. Parametric optimization of elliptical dimple attributes can enhance load-carrying capacity and reduce frictional losses in bearings, with synergistic effects observed when combined with micro-roughness.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY
(2021)
Article
Chemistry, Physical
Yanqing Gu et al.
Summary: The study found that the coating thickness on the surface of the spindle hook teeth ranged from 66.1 µm to 74.4 µm, with chromium being the major chemical element and a small amount of nickel. Wear failure of the teeth was mainly due to abrasive wear, oxidative wear, and fatigue peeling, with the wear area increasing exponentially and the wear width increasing linearly as the picking area expanded.
Article
Materials Science, Multidisciplinary
Yong Zhu et al.
MATERIALS RESEARCH EXPRESS
(2020)
Article
Chemistry, Physical
Auezhan Amanov et al.
Article
Mechanics
F. Poehl
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
(2019)
Article
Materials Science, Multidisciplinary
Luigi D'Avico et al.
Article
Materials Science, Multidisciplinary
Yi Ding et al.
Article
Materials Science, Coatings & Films
J. L. Daure et al.
SURFACE & COATINGS TECHNOLOGY
(2018)
Article
Engineering, Mechanical
Fanming Meng et al.
INDUSTRIAL LUBRICATION AND TRIBOLOGY
(2016)
Article
Engineering, Mechanical
F. M. Meng et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE
(2014)
Article
Engineering, Mechanical
A Leyland et al.
