Related references
Note: Only part of the references are listed.Autogenous laser-welded dissimilar joint of ferritic/martensitic P92 steel and Inconel 617 alloy: mechanism, microstructure, and mechanical properties
Amit Kumar et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)
Development of a probability distribution model for the SCFs in tubular X-connections retrofitted with FRP
Hossein Nassiraei et al.
STRUCTURES (2022)
Numerical and experimental investigation on distribution of residual stress and the influence of heat treatment in multi-pass dissimilar welded rotor joint of alloy 617/10Cr steel
Rajiv Kumar et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2022)
Recent progress of residual stress measurement methods: A review
Jiang GUO et al.
CHINESE JOURNAL OF AERONAUTICS (2021)
SCFs in tubular X-connections retrofitted with FRP under in-plane bending load
Hossein Nassiraei et al.
COMPOSITE STRUCTURES (2021)
An efficient computational approach for heat source optimization in numerical simulations of arc welding processes
R. M. Farias et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2021)
The Performance of CR180IF and DP600 Laser Welded Steel Sheets under Different Strain Rates
Maria Mihalikova et al.
MATERIALS (2021)
Investigation of residual stresses in planar dissimilar magnetic pulse welds by neutron diffraction
M-N Avettand-Fenoel et al.
JOURNAL OF MANUFACTURING PROCESSES (2021)
Effect of single initial overload and mean load on the low-cycle fatigue life of normalized 300 M alloy steel Cheek
Chris Bassindale et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Microstructure and mechanical properties of aluminum alloy prepared by laser-arc hybrid additive manufacturing
Miaoran Liu et al.
JOURNAL OF LASER APPLICATIONS (2020)
Heat Source Models in Numerical Simulations of Laser Welding
Tomasz Kik
MATERIALS (2020)
Stress concentration factors in tubular T/Y-joints strengthened with FRP subjected to compressive load in offshore structures
Hossein Nassiraei et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Fatigue life prediction for butt-welded joints considering weld-induced residual stresses and initial damage, relaxation of residual stress, and elasto-plastic fatigue damage
Xiaojia Wang et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2019)
Welding defects detection based on deep learning with multiple optical sensors during disk laser welding of thick plates
Yanxi Zhang et al.
JOURNAL OF MANUFACTURING SYSTEMS (2019)
A Modified Johnson-Cook Model for Dynamic Response of Metals with an Explicit Strain- and Strain-Rate-Dependent Adiabatic Thermosoftening Effect
B. Song et al.
JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS (2019)
Numerical simulation and experimental validation of residual stress and welding distortion induced by laser-based welding processes of thin structural steel plates in butt joint configuration
Ehsan Dezhparvar Derakhshan et al.
OPTICS AND LASER TECHNOLOGY (2018)
Residual stress modelling in laser welding marine steel EH36 considering a thermodynamics-based solid phase transformation
Youmin Rong et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2018)
Effects of Pulsed Nd:YAG Laser Welding Parameters on Penetration and Microstructure Characterization of a DP1000 Steel Butt Joint
Xin Xue et al.
METALS (2017)
Residual stresses induced by laser welding process in the case of a dual-phase steel DP600: Simulation and experimental approaches
A. Kouadri-Henni et al.
MATERIALS & DESIGN (2017)
Optimal parameters for laser welding of advanced high-strength steels used in the automotive industry
F. A. O. Fernandes et al.
MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE 2017 (MESIC 2017) (2017)
Comparison of Quasi-Static Constitutive Equations and Modeling of Flow Curves for Austenitic 304 and Ferritic 430 Stainless Steels
B. Sener et al.
ACTA PHYSICA POLONICA A (2017)
Effect of strain rate on flow stress and anisotropy of DP600, TRIP780, and AA5182-O sheet metal alloys
T. Rahmaan et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2016)
Neutron diffraction measurements of residual stress in additively manufactured stainless steel
D. W. Brown et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Dislocation density based model for plastic deformation and globularization of Ti-6Al-4V
Bijish Babu et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2013)
Dynamic behavior and a modified Johnson-Cook constitutive model of Inconel 718 at high strain rate and elevated temperature
Xiangyu Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Nd:YAG laser welding of sheet metal assembly: Transformation induced volume strain affect on elastoplastic model
C. Seang et al.
LASERS IN MANUFACTURING (LIM 2013) (2013)
Microstructure and mechanical properties of laser welded DP600 steel joints
N. Farabi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Constitutive relationships for 22MnB5 boron steel deformed isothermally at high temperatures
M. Naderi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Delayed cracking in 301LN austenitic steel after deep drawing: Martensitic transformation and residual stress analysis
M. R. Berrahmoune et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
Behavior of high strength structural steel at elevated temperatures
Ju Chen et al.
JOURNAL OF STRUCTURAL ENGINEERING (2006)
Average shear stress yield criterion and its application to plastic collapse analysis of pipelines
Xian-Kui Zhu et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2006)
Quasi-static and dynamic loading responses and constitutive modeling of titanium alloys
AS Khan et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2004)
Electron beam welding, laser beam welding and gas tungsten arc welding of titanium sheet
YL Qi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)