Related references
Note: Only part of the references are listed.Characterization of 3D-printed PLA parts with different raster orientations and printing speeds
Mohammad Reza Khosravani et al.
SCIENTIFIC REPORTS (2022)
Design for 3D Printed Tools: Mechanical Material Properties for Direct Polymer Additive Tooling
Peter Frohn-Soerensen et al.
POLYMERS (2022)
Tensile, three-point bending and impact strength of 3D printed parts using PLA and recycled PLA filaments: A statistical investigation
Gurcan Atakok et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)
A comprehensive study on ring shape specimens under compressive and tensile loadings for covering the full range of I plus II fracture modes of gypsum material
Hamid Reza Karimi et al.
INTERNATIONAL JOURNAL OF ROCK MECHANICS AND MINING SCIENCES (2022)
Experimental characterization and mechanical behavior of 3D printed CFRP
Kouider Bendine et al.
EUROPEAN JOURNAL OF MECHANICS A-SOLIDS (2022)
Large-Scale Automated Additive Construction: Overview, Robotic Solutions, Sustainability, and Future Prospect
Mohammad Reza Khosravani et al.
SUSTAINABILITY (2022)
Effect of printing parameters on the structure and high strain rate deformation behavior of additively manufactured 316L stainless steel
Kenneth Hukpati et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)
Printing parameters and materials affecting mechanical properties of FDM-3D printed Parts: Perspective and prospects
Manav Doshi et al.
MATERIALS TODAY-PROCEEDINGS (2022)
Fracture toughness characteristics of additively manufactured Ti-6Al-4V lattices
Stephen Daynes et al.
EUROPEAN JOURNAL OF MECHANICS A-SOLIDS (2021)
Compressive behaviors of 3D printed polypropylene-based composites at low and high strain rates
Kui Wang et al.
POLYMER TESTING (2021)
Investigation by Digital Image Correlation of Mixed-Mode I and II Fracture Behavior of Polymeric IASCB Specimens with Additive Manufactured Crack-Like Notch
Tommaso Maria Brugo et al.
MATERIALS (2021)
Multiaxial fatigue behaviour of maraging steel produced by selective laser melting
R. Branco et al.
MATERIALS & DESIGN (2021)
On the use of edge cracked short bend beam specimen for PMMA fracture toughness testing under mixed-mode I/II
S. S. Mousavi et al.
POLYMER TESTING (2020)
Progress and challenges in fabrication of wearable sensors for health monitoring
Sara Nasiri et al.
SENSORS AND ACTUATORS A-PHYSICAL (2020)
Scale and size effects on the mechanical properties of bioinspired 3D printed two-phase composites
Frances Y. Su et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
3D food printing of as the new way of preparing food: A review
Sylvester Mantihal et al.
INTERNATIONAL JOURNAL OF GASTRONOMY AND FOOD SCIENCE (2020)
A new specimen for mixed mode I/II fracture of brittle and quasi-brittle materials
Yifan Li et al.
1ST VIRTUAL EUROPEAN CONFERENCE ON FRACTURE - VECF1 (2020)
Structural performance of 3D-printed composites under various loads and environmental conditions
Mohammad Reza Khosravani et al.
POLYMER TESTING (2020)
Effect of printing strategies on forming accuracy and mechanical properties of ZrO2 parts fabricated by SLA technology
Xiangsong Fu et al.
CERAMICS INTERNATIONAL (2019)
Application of Additive Manufacturing technology to an Aerospace component for better trade-off's
Kanuparti Vishnu Prashant Reddy et al.
MATERIALS TODAY-PROCEEDINGS (2018)
Calculation of the crack tip parameters in the holed-cracked flattened Brazilian disk (HCFBD) specimens under wide range of mixed mode I/II loading
J. Akbardoost et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2017)
A generalized strain energy density criterion for mixed mode fracture analysis in brittle and quasi-brittle materials
M. R. Ayatollahi et al.
THEORETICAL AND APPLIED FRACTURE MECHANICS (2015)
3D printing in aerospace and its long-term sustainability
Sunil C. Joshi et al.
VIRTUAL AND PHYSICAL PROTOTYPING (2015)
Effects of build orientation on tensile strength for stereolithography-manufactured ASTM D-638 type I specimens
Rolando Quintana et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Materials analysis of stereolithography resins for use in Rapid Manufacturing
R Hague et al.
JOURNAL OF MATERIALS SCIENCE (2004)
The role of T-stress in brittle fracture for linear elastic materials under mixed-mode loading
DJ Smith et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2001)