☆ 4.7 Article

Improving mechanical and wear properties of multiphase M50 steel by tailoring bainite morphology

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Roles of pre-formed martensite in below- M s bainite formation, microstructure, strain partitioning and impact absorption energies of low-carbon bainitic steel

Lihe Qian et al.

Summary: The pre-formation of martensite accelerates the early stage of bainite transformation, but delays the finishing time. It refines the crystal structure of bainite and retained austenite, and promotes relatively uniform strain partitioning among various phases.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Engineering, Mechanical

Effect of nano-bainite microstructure and residual stress on friction properties of M50 bearing steel

X. F. Yu et al.

Summary: Through experimental analysis on M50 bearing steel, it was found that nano-bainite structure and residual stress have significant effects on the friction properties of the material.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

A novel route to improve the fatigue properties of aviation M50 steel via tailoring the bainite content and cold deformation

Feng Wang et al.

Summary: The microstructure, mechanical and fatigue properties of M50 steel were studied by combining austempering processing with cold deformation. The introduction of bainite effectively refined the multiphase microstructure. The finest microstructure and the best combination of strength and toughness were obtained when the bainite content was 10.5%. Cold deformation of 20% led to a slight improvement in tensile strength and impact toughness, but larger cold deformation significantly deteriorated the mechanical properties. The study concludes that mechanical properties can be improved by tailoring the bainite content to approximately 10% and the cold deformation degree to 20%. The tailored specimen exhibited a 114.1% longer specific life of rolling contact fatigue compared to traditional martensitic quenched specimens, indicating improved resistance to fatigue. The findings suggest that strict tailoring of bainite content and cold deformation degree can enhance the fatigue properties of M50 steel.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Chemistry, Physical

Influence of friction-induced retained austenite transformation to martensite on the wear properties of a carburized layer of 23CrNi3MoA steel

Zhenlong Zhu et al.

Summary: This study investigates the effect of friction-induced retained austenite transformation to martensite on the surface wear performance of steel. The results show that the size of the retained austenite plays a key role in controlling the mechanical stability of austenite, with smaller size and uniform distribution leading to higher stability and reduced wear. Microstructural characterization reveals the formation and extension mechanism of cracks during wear, providing a basis for controlling retained austenite during production.

APPLIED SURFACE SCIENCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Austempering Temperature on Microstructure and Mechanical Properties of M50 Bearing Steel

Y. Su et al.

Summary: The effect of austempering temperature on the bainite transformation, carbide precipitation, hardness, and impact toughness of M50 bearing steel was studied using microstructure observation and mechanical property tests. The results show that the austempering temperature significantly affects the bainite content, carbide content, hardness, and impact toughness of the steel.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of various phase fraction of bainite, intercritical ferrite, retained austenite and pearlite on the corrosion behavior of multiphase steels

Neetu et al.

Summary: The work discusses the corrosion behavior of newly developed high strength and highly ductile multi-phase steels made up of various fractions of different structures, and found that multiphase interaction and rust constituents play a key role in corrosion, with corrosion rate initially increasing with continuous cooling time and then decreasing once pearlite appears.

CORROSION SCIENCE (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure Evolution and Tempering Transformation Kinetics in a Secondary Hardened M50 Steel Subjected to Cold Ring Rolling

Feng Wang et al.

Summary: The microstructure evolution and tempering transformation kinetics of M50 steel during cold ring rolling (CRR) were studied. The results showed that CRR weakened the brass texture and increased the low angle boundaries, leading to changes in activation energy and carbon content during tempering. Additionally, CRR affected the segregation of carbon atoms and precipitation of transition carbide, ultimately influencing the mechanical properties of the steel.

ISIJ INTERNATIONAL (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Tempering response and improved mechanical properties in secondary hardened steel by introducing an optimized austempering process

Feng Wang et al.

Summary: The tempering response and mechanical properties of austempered Cr4Mo4V steel were studied, showing improved properties with optimized austempering process but strict control of bainite content to prevent blocky RA and bainite coarsening.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of introduced vanadium carbide at the bay region on bainite transformation, microstructure and mechanical properties of high-carbon and high-silicon steel

Dongyun Sun et al.

Summary: The introduction of fine VC precipitation during bay treatment notably accelerates the initial bainite transformation by reducing the incubation period by 91%. Decrease in activation energy for bainite nucleation at vanadium carbide/austenite interfaces and generation of preferred nucleation sites lead to a favorable acceleration of bainitic formation kinetics.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Multiphase microstructure formation and its effect on fracture behavior of medium carbon high silicon high strength steel

Kui Chen et al.

Summary: This study investigated the evolution of multiphase microstructure and impact fracture behavior of medium carbon high silicon high strength steel after austempering treatment at different temperatures. The results show that with the increase of treatment temperature, the carbon concentration in the matrix decreases, and impact toughness initially increases then gradually decreases. Different treatment temperatures lead to variations in fracture mechanisms and characteristics of the samples.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of bainite fraction on hydrogen embrittlement of bainite/martensite steel

Jang Woong Jo et al.

Summary: This study demonstrates the significance of the bainite fraction in dual-phase steel on its resistance to hydrogen embrittlement. Increasing the number of fine cementite particles in bainite can enhance the hydrogen embrittlement resistance of the steel.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Pressure on Microstructure and Residual Stresses during Hot Isostatic Pressing Post Treatment of AISI M50 Produced by Laser Powder-Bed Fusion

Siyuan Qin et al.

Summary: HIP technology densifies materials, modifies their microstructure, retards recrystallization during austenitization, and results in slight compressive residual stresses on the surface.

METALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Crystallographic texture evolution and martensite transformation in the strain hardening process of a ferrite-based low density steel

Mingxiang Liu et al.

Summary: The strain-induced martensite transformation plays a crucial role in the strain hardening process of low-density steel. This transformation is affected by the texture evolution and grain size of austenite, influencing the rate of martensite transformation in each stage of strain hardening. The presence of TWIP effect and high density dislocations during martensite transformation contributes to continuous hardening, but the final stage is slowed down by unfavorable orientation and reduced grain size of austenite.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Bainite kinetic energy, activation energy, and tribological behavior of austempered AISI4340 steel

Xue Han et al.

Summary: The study investigated the effect of heat-treatment on the microstructures of commercial quality AISI4340 steel after austenitizing at 1128 K and austempering at temperatures ranging from 561 K to 644 K. The results showed that the bainite sheaves and bainite width grow as the austempering temperature increases. High temperature results in fast bainite transformation, and the bainite activation energy is 5.302 x 10(3) J/mol. The bainite microstructures exhibit significantly enhanced tribological performance compared to tempered martensite microstructures at the same hardness.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructures and properties of a novel carburizing nanobainitic bearing steel

Yanhui Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of martensite/austenite interfaces on bainite formation in low-alloy steels below Ms

Ashwath M. Ravi et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Bainite kinetic transformation of austempered AISI 6150 steel

Xue Han et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Mechanical Properties of M50 Steel by Combining Cold Rolling with Austempering

Dongsheng Qian et al.

METALS (2020)

Add to Collection

Article Crystallography

The Effect of Lath Martensite Microstructures on the Strength of Medium-Carbon Low-Alloy Steel

Chen Sun et al.

CRYSTALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Evolution of microstructure and mechanical properties during tempering of M50 steel with Bainite/Martensite duplex structure

Feng Wang et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Engineering, Mechanical

The effect of prior cold rolling on the carbide dissolution, precipitation and dry wear behaviors of M50 bearing steel

Feng Wang et al.

TRIBOLOGY INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Enhanced toughness of bearing steel by combining prior cold deformation with martensite pre-quenching and bainite transformation

Xiaohui Lu et al.

MATERIALS LETTERS (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Accelerating nano-bainite transformation based on a new constructed microstructural predicting model

Zhinan Yang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Engineering, Mechanical

Understanding the factors controlling rolling contact fatigue damage in VIM-VAR M50 steel

J. Jelita Rydel et al.

INTERNATIONAL JOURNAL OF FATIGUE (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Toughness dependence of nano-bainite on phase fraction and morphology

Avanish Kumar et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural Evolution and Ductile-to-Brittle Transition in a Low-Carbon MnCrMoNiCu Heavy Plate Steel

Dongsheng Liu et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)

Add to Collection

Article Engineering, Mechanical

Fatigue crack nucleation and propagation at clustered metallic carbides in M50 bearing steel

Jian Guan et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Engineering, Mechanical

Three-body abrasive wear of carbide-free bainite, martensite and bainite-martensite structure of similar hardness

Minal Shah et al.

WEAR (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Relationship between microstructure and mechanical properties of M50 ultra-high strength steel via quenching-partitioning-tempering process

Lina Zhou et al.

MATERIALS CHARACTERIZATION (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and wear behavior of in-situ hypereutectic Al-high Si alloys produced by selective laser melting

Nan Kang et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of Clusters in Medium Carbon Secondary Hardening Ultra-high-strength Steel After Hardening and Aging Treatments

R. Veerababu et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)

Add to Collection

Article Chemistry, Physical

The effect of ion implantation on tribology and hot rolling contact fatigue of Cr4Mo4Ni4V bearing steel

Jie Jin et al.

APPLIED SURFACE SCIENCE (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and texture evolution in a twinning-induced-plasticity steel during uniaxial tension

Ahmed A. Saleh et al.

ACTA MATERIALIA (2013)

Add to Collection

Review Materials Science, Multidisciplinary

Steels for bearings

H. K. D. H. Bhadeshia

PROGRESS IN MATERIALS SCIENCE (2012)

Add to Collection

Article Nanoscience & Nanotechnology

A new effect of retained austenite on ductility enhancement in high-strength quenching-partitioning-tempering martensitic steel

Ke Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Substructure on Toughness of Lath Martensite/Bainite Mixed Structure in Low-Carbon Steels

Luo Zhi-jun et al.

JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2010)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Ductile-brittle transition temperature of ultrafine ferrite/cementite microstructure in a low carbon steel controlled by effective grain size

T Hanamura et al.

ISIJ INTERNATIONAL (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.