☆ 4.7 Review

The Additive Manufacturing Approach to Polydimethylsiloxane (PDMS) Microfluidic Devices: Review and Future Directions

POLYMERS (2023)

Related references

Note: Only part of the references are listed.

Article Polymer Science

Aging of UV curable PDMS developed for large-scale, high viscosity stereolithography

Hongtao Song et al.

Summary: This study investigates the use of photosensitive platinum catalysts for UV-activated hydrosilylation of PDMS, which enables the additive manufacturing of PDMS objects. The aging behavior of Pt-catalyzed, UV-curable PDMS samples is studied, including their mechanical behavior under thermal and UV-accelerated aging conditions. The results show that the Pt-catalyzed, UV-curable PDMS undergoes aging, resulting in increased stiffness and decreased elongation, likely due to the formation of additional crosslinks. The PDMS formulation exhibits greater mechanical strength and significantly less reduction in strength with aging compared to commonly used thiol-ene PDMS.

POLYMER DEGRADATION AND STABILITY (2023)

Add to Collection

Article Engineering, Manufacturing

Additive Manufacturing for Bioinspired Structures: Experimental Study to Improve the Multimaterial Adhesion Between Soft and Stiff Materials

Gianni Stano et al.

Summary: The fabrication of bioinspired structures using material extrusion additive manufacturing technology has gained popularity in soft robotics. Stiff-soft bioinspired structures activated by shape memory alloy actuators have been successfully manufactured and tested. The gyroid infill was found to produce better mechanical properties compared to the widely studied lines infill. An experimental study was conducted to improve the adhesion at the interface between stiff and soft materials using an inexpensive method. By optimizing interface geometry, mesh overlapping, and annealing post-treatment, a significant improvement in the adhesion strength was achieved. A bioinspired robotic finger was successfully fabricated and tested, demonstrating the potential of the proposed additive manufacturing approach in realizing bioinspired systems.

3D PRINTING AND ADDITIVE MANUFACTURING (2023)

Add to Collection

Article Engineering, Manufacturing

Embedded 3D Printing of PDMS-Based Microfluidic Chips for Biomedical Applications

Weijian Hua et al.

Summary: This study investigates a fumed silica-PDMS suspension for embedded 3D printing (e-3DP) matrix bath, enabling the low-cost extrusion 3D printing of microfluidic chips with complex embedded channels. The addition of fumed silica particles effectively changes PDMS from a viscous solution to a yield-stress suspension suitable for e-3DP. The mechanical properties of the crosslinked fumed silica-PDMS are enhanced with an increased concentration of fumed silica. Although transparency is reduced, the printed microfluidic chips remain acceptable. The proposed fumed silica-PDMS suspension-enabled e-3DP method is successfully validated through the printing of two representative microfluidic chips for biomedical applications.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Embedded 3D Printing of Thermally-Cured Thermoset Elastomers and the Interdependence of Rheology and Machine Pathing

Maria Stang et al.

Summary: Traditional 3D printing methods are not effective for thermally-cured thermoset elastomers due to their viscosity, gelation kinetics, and surface tension. In this study, the researchers achieved complex 3D printing of thermoset elastomers by modifying the rheological properties of the material and implementing print process controls, opening up new possibilities for the application of these materials.

ADVANCED MATERIALS TECHNOLOGIES (2023)

Add to Collection

Article Polymer Science

A Preliminary Experimental Study of Polydimethylsiloxane (PDMS)-To-PDMS Bonding Using Oxygen Plasma Treatment Incorporating Isopropyl Alcohol

Anthony Tony et al.

Summary: This study presents a simple and effective method to enhance the bonding strength between polydimethylsiloxane (PDMS) and PDMS using isopropyl alcohol (IPA). The results showed that our method significantly improved the irreversible bonding strength of PDMS-to-PDMS, up to 3.060 MPa for natural-cured PDMS and 1.373 MPa for heat-cured PDMS, while the best bonding strength with the existing method in literature is 1.9 MPa.

POLYMERS (2023)

Add to Collection

Article Chemistry, Physical

Functional modification of polydimethylsiloxane nanocomposite with silver nanoparticles-based montmorillonite for antibacterial applications

Xinrong Huang et al.

Summary: Functionalization of polydimethylsiloxane nanocomposites with advanced nanostructure materials can lead to significant improvements in mechanical and antimicrobial properties. This research presents a creative and easy technique for incorporating silver nanoparticles-lecithin modified montmorillonite into PDMS nanocomposites for antibacterial applications.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2022)

Add to Collection

Article Automation & Control Systems

Development of a customised 3D printer as a potential tool for direct printing of patient-specific facial prosthesis

Cormac D. Fay et al.

Summary: This study demonstrates a cost-effective portable fabrication system for 3D printing complex structures from PDMS using a photo-initiator and a LED curing process. The 3D printer has the potential to create facial and other prostheses, and has potential applications in areas such as microfluidics, flexible electronics, and biomedicine.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection

Article Automation & Control Systems

Projection micro-stereolithography versus master-slave approach to manufacture a micro-optofluidic device for slug flow detection

Lorena Saitta et al.

Summary: This work presents the use of projection micro-stereolithography (P mu SL) to 3D print a micro-optofluidic device for slug flow detection. A comparison with a poly-dimethylsiloxane (PDMS)-based device was conducted using a novel master-slave 3D printing approach. The optical fiber insertions and absorption phenomenon were utilized for flow detection, showing different light transmission with fluid interference in a micro-channel.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Development of Paper Microfluidics with 3D-Printed PDMS Barriers for Flow Control

Chang Chen et al.

Summary: This article reports a systematic study on the 3D printing protocol, characterization, and application of PDMS barriers for flow control in paper microfluidics. The results suggest that increasing the penetration depth of the barriers is more efficient in delaying flow than increasing the length of partially penetrated barriers (PPBs). This study improves our understanding of 3D PDMS barrier fabrication and flow control in paper microfluidics.

ACS APPLIED MATERIALS & INTERFACES (2022)

Add to Collection

Article Polymer Science

High-Linearity Hydrogel-Based Capacitive Sensor Based on Con A-Sugar Affinity and Low-Melting-Point Metal

Ruixue Yin et al.

Summary: A capacitive glucose sensor with high linearity and a wide detection range was developed based on affinity sensing and glucose-responsive hydrogel. The sensor showed good anti-interference performance, reversibility, and long-term stability, making it suitable for continuous glucose monitoring.

POLYMERS (2022)

Add to Collection

Review Chemistry, Analytical

Emerging 3D printing technologies and methodologies for microfluidic development

Giraso Keza Monia Kabandana et al.

Summary: This review paper examines recent advancements in 3D printed microfluidics, discussing three main 3D printing technologies and new emerging 3D-printing technologies. It analyzes their advantages, limitations, and potential applications in the field of microfluidics.

ANALYTICAL METHODS (2022)

Add to Collection

Article Biochemical Research Methods

Highly accurate multiprotein detection on a digital ELISA platform

Shih-Mo Yang et al.

Summary: The emerging single-molecule detection platform, digital enzyme-linked immunosorbent assay (ELISA), can detect multiple proteins simultaneously at low concentrations. By using encoded magnetic microbeads, we developed a multiple single-molecule detection digital ELISA approach to detect multiple cytokines at once. The approach was successfully applied in distinguishing asthma-related cytokines in children.

LAB ON A CHIP (2022)

Add to Collection

Article Engineering, Biomedical

Properties and Applications of PDMS for Biomedical Engineering: A Review

Ines Miranda et al.

Summary: This review provides an overview of the properties of PDMS and its applications in the field of micro and nanoengineering. PDMS is widely used in biomedical applications due to its excellent optical, electrical, and mechanical properties, as well as biocompatibility. The introduction of the soft-lithography technique has facilitated the rapid prototyping of micro and nanostructures using PDMS, leading to advances in microfluidics, electronics, and biomedicine.

JOURNAL OF FUNCTIONAL BIOMATERIALS (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Direct ink writing 3D printing of polydimethylsiloxane-based soft and composite materials: a mini review

Yun Li et al.

Summary: This article provides a critical perspective on the advances and potential of PDMS-based DIW technology, summarizing key factors and innovations, and showcasing state-of-the-art structures and applications. It also offers guidelines for those interested in PDMS-based DIW.

OXFORD OPEN MATERIALS SCIENCE (2022)

Add to Collection

Review Materials Science, Biomaterials

Beyond Polydimethylsiloxane: Alternative Materials for Fabrication of Organ-on-a-Chip Devices and Microphysiological Systems

Scott B. Campbell et al.

Summary: PDMS is commonly used in organ-on-a-chip devices and microphysiological systems due to its ease-of-use, elasticity, and optical transparency, but its limitations in the absorption of small molecules and high-throughput manufacturing have led researchers to explore alternative materials such as elastomers, hydrogels, and thermoplastic polymers. The development of organ-on-a-chip devices based on these alternative materials is trending, with researchers focusing on overcoming obstacles to create versatile devices for personalized medicine and drug discovery.

ACS BIOMATERIALS SCIENCE & ENGINEERING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Structure-Mechanical Property Relationships of 3D-Printed Porous Polydimethylsiloxane

Rebekah Woo et al.

Summary: Porous PDMS exhibits highly tunable mechanical properties, which can be achieved by adjusting infill densities and printing patterns, providing new insights for designing adaptive soft robots and actuators.

ACS APPLIED POLYMER MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Digital Light Processing 3D Printing of PDMS-Based Soft and Elastic Materials with Tunable Mechanical Properties

Ke Du et al.

Summary: The developed silicone thiourea resins improve the elasticity of 3D-printed silicones by increasing dynamic noncovalent intermolecular interactions between polymer chains through the introduction of thiourea groups. A molecular design strategy was implemented to adjust the ratio of thiourea segments using oligomeric and polymeric PDMS units. The cured silicone elastomer displayed a maximum elongation of up to 1000% under tensile load and excellent cyclic compression durability, allowing for the 3D printing of PDMS-based objects with complex microarchitectures, high resolution, excellent surface finishing, and low cytotoxicity, with potential applications in medical devices, wearable devices, and soft robotics.

ACS APPLIED POLYMER MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Development model and experimental characterization of residual stress of 3D printing PLA parts with porous structure

Li Zhao et al.

Summary: The study established a development model of residual stress with porous structure using FDM, finding a linear correlation between residual stress and stress concentration coefficient. Samples with different sizes were fabricated to evaluate residual stresses on the surface, concluding that pore size affects surface residual stress. The accuracy of theoretical modeling was confirmed, providing guidance for 3D printing porous structures.

APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2021)

Add to Collection

Article Engineering, Environmental

Covalent adaptable networks of polydimethylsiloxane elastomer for selective laser sintering 3D printing

Shaojie Sun et al.

Summary: Researchers successfully achieved powder-based SLS 3D printing of PDMS elastomer using a novel PDMS covalent adaptable network, demonstrating excellent self-healing and reprocessing properties. By optimizing the morphology of PDMS powders, a complex structure PDMS insole based on personalized foot pressure distribution data was printed, showcasing foot orthotic and self-healing functions.

CHEMICAL ENGINEERING JOURNAL (2021)

Add to Collection

Article Biochemical Research Methods

Systematically Studying Dissolution Process of 3D Printed Acrylonitrile Butadiene Styrene (ABS) Mold for Creation of Complex and Fully Transparent Polydimethylsiloxane (PDMS) Fluidic Devices

Pin-Chuan Chen et al.

Summary: The study aimed to create complex, three-dimensional, and transparent PDMS fluidic devices by utilizing ultrasonication to remove ABS molds, solvent vapor polishing of 3D-printed molds, and ensuring the circulation of fresh solvent solution. These modifications improved the efficiency and quality of the PDMS device fabrication process.

BIOCHIP JOURNAL (2021)

Add to Collection

Article Engineering, Mechanical

The effect of heterogeneous surface charges on mixing in a combined electroosmotic/pressure-driven micromixer

A. Farahinia et al.

Summary: This study numerically investigates electro-osmotic flow in heterogeneous microchannels using the approximate Helmholtz-Smoluchowski model and examines the mixing performance. It is found that by combining two fluid flows and adjusting the arrangement of heterogeneities, a micro-mixer with adjustable mixing performance can be designed. Therefore, heterogeneities have an optimal application point in terms of mixing efficiency in micro-mixers.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2021)

Add to Collection

Article Engineering, Biomedical

Effect of heat treatment on mechanical properties of 3D printed PLA

N. Jayanth et al.

Summary: Heat treating 3D printed parts can significantly improve their mechanical properties, especially tensile strength. Heat treatment also reduces internal stresses developed during printing and enhances the formation of bonds between filaments.

JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2021)

Add to Collection

Review Chemistry, Analytical

Tactile and Thermal Sensors Built from Carbon-Polymer Nanocomposites-A Critical Review

Chenwang Yuan et al.

Summary: This paper provides a critical review of tactile and thermal sensors built from carbon nanomaterial-filled polymer composites, using a systematic knowledge architecture to classify information and knowledge. It discusses the principle behind these composites functioning as temperature and pressure sensors, the different structures of CNPC sensors, as well as their behavior and performance. The review also explores the fabrication of CNPC sensors and suggests future research directions, including the need for a network of CNPC sensors that can be installed on curved bodies like robots.

SENSORS (2021)

Add to Collection

Article Chemistry, Analytical

PDMS Curing Inhibition on 3D-Printed Molds: Why? Also, How to Avoid It?

Bastien Venzac et al.

Summary: A systematic study using 16 commercial resins identified a fast and straightforward treatment for 3D-printed structures to support accurate PDMS replication using UV and/or thermal post-curing. Analysis revealed that phosphine oxide-based photo-initiators were poisoning the Pt-based PDMS catalyst, but were eliminated and recombined into high molecular weight species upon UV and/or thermal treatments.

ANALYTICAL CHEMISTRY (2021)

Add to Collection

Article Chemistry, Analytical

Advancing 3D-Printed Microfluidics: Characterization of a Gas-Permeable, High-Resolution PDMS Resin for Stereolithography

Elyse Fleck et al.

Summary: With the application of additive manufacturing technology, researchers have developed a gas-permeable and high-resolution PDMS resin, providing a new approach for the manufacturing of microfluidic devices.

MICROMACHINES (2021)

Add to Collection

Article Polymer Science

Mechanical Properties of FDM Printed PLA Parts before and after Thermal Treatment

Ali Chalgham et al.

Summary: This study investigates the influence of process parameters on the mechanical properties of PLA samples in Fused Deposition Modeling (FDM) technology, as well as the effects of post-heat treatment on them.

POLYMERS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

3D Printing of a PDMS Cylindrical Microlens Array with 100% Fill-Factor

Houchao Zhang et al.

Summary: The study introduces a method for efficiently manufacturing CMLAs with a high fill-factor using electric-field-driven microscale 3D printing of PDMS. By adjusting printing parameters, the profile and fill-factor of CMLAs can be controlled to enhance their optical performance. The results show good morphology and optical properties of the prepared CMLAs, suggesting a potential cost-effective route for manufacturing large-area CMLAs.

ACS APPLIED MATERIALS & INTERFACES (2021)

Add to Collection

Article Engineering, Mechanical

Exploiting limitations of fused deposition modeling to enhance mixing in 3D printed microfluidic devices

Mojtaba Zeraatkar et al.

Summary: This study introduces an alternative construction for microfluidic micromixers using the effect of extruded filaments in FDM technique. Experimental and numerical studies showed that the geometrical features on microchannels can act as ridges and enhance chaotic mixing through transverse movement of fluids. Compared to other methods, FDM offers a simpler fabrication process with inherent properties that enhance mixing processes.

RAPID PROTOTYPING JOURNAL (2021)

Add to Collection

Review Polymer Science

3D Printing at Micro-Level: Laser-Induced Forward Transfer and Two-Photon Polymerization

Muhammad Arif Mahmood et al.

Summary: Laser-induced forward transfer (LIFT) and two-photon polymerization (TPP) are two methods that have demonstrated their ability to produce complex microstructures at an extraordinary level, making them valuable tools for researchers and technologists. Understanding the processes and characteristics of the manufactured parts is essential to harness the benefits of LIFT and TPP in 3D printing.

POLYMERS (2021)

Add to Collection

Proceedings Paper Automation & Control Systems

Toward a Soft Microfluidic System: Concept and Preliminary Developments

A. Tony et al.

Summary: This paper introduces the concept of Integrated Microfluidic Circuits (IMCs) and soft microfluidic systems (SMS), which are robotic systems without electronics that can achieve control, sensing, and movement. Additionally, the authors propose the concepts of continuous switch valves and horizontal stacking of multiple layers in microfluidic systems.

2021 27TH INTERNATIONAL CONFERENCE ON MECHATRONICS AND MACHINE VISION IN PRACTICE (M2VIP) (2021)

Add to Collection

Article Chemistry, Analytical

Determination of total protein content in biomedical products by the PDMS-assisted lab-in-a-syringe assay using 3D printed scaffolds removal

Ester Drastikova et al.

Summary: The study aimed to develop a low-cost, portable device for rapid determination of total protein content using PDMS-based technology, with two different fabrication procedures tested. Results showed that the one-step PDMS microdevices were superior in terms of preparation, repeatability, and reagent stability, and were successfully used for total protein content determination in biomedical products.

JOURNAL OF ANALYTICAL SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

Effects of processing conditions on mechanical properties of PLA printed parts

Morteza Behzadnasab et al.

RAPID PROTOTYPING JOURNAL (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Inkjet Printable Polydimethylsiloxane for All-Inkjet-Printed Multilayered Soft Electrical Applications

Riikka Mikkonen et al.

ACS APPLIED MATERIALS & INTERFACES (2020)

Add to Collection

Article Chemistry, Analytical

3D Printed Microfluidics

Anna V. Nielsen et al.

ANNUAL REVIEW OF ANALYTICAL CHEMISTRY, VOL 13 (2020)

Add to Collection

Review Polymer Science

PDMS microfluidics: A mini review

Kiran M. Raj et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Experimental and simulation study of flow patterns in the combined flow focusing and T-junction device

Lei Lei et al.

JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2020)

Add to Collection

Article Multidisciplinary Sciences

A dog oviduct-on-a-chip model of serous tubal intraepithelial carcinoma

Marcia de Almeida Monteiro Melo Ferraz et al.

SCIENTIFIC REPORTS (2020)

Add to Collection

Article Multidisciplinary Sciences

3D-printing process design of lattice compressor impeller based on residual stress and deformation

Dejun Jia et al.

SCIENTIFIC REPORTS (2020)

Add to Collection

Article Multidisciplinary Sciences

3D printed mold leachates in PDMS microfluidic devices

Marcia de Almeida Monteiro Melo Ferraz et al.

SCIENTIFIC REPORTS (2020)

Add to Collection

Article Engineering, Biomedical

3D-Printed micro-optofluidic device for chemical fluids and cells detection

Fabiana Cairone et al.

BIOMEDICAL MICRODEVICES (2020)

Add to Collection

Article Polymer Science

Facile Photo and Thermal Two-Stage Curing for High-Performance 3D Printing of Poly(Dimethylsiloxane)

Ji Zhongying et al.

MACROMOLECULAR RAPID COMMUNICATIONS (2020)

Add to Collection

Review Biotechnology & Applied Microbiology

Recent advances in multi-material additive manufacturing: methods and applications

Daehoon Han et al.

CURRENT OPINION IN CHEMICAL ENGINEERING (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Residual stress analysis of additive manufacturing of metallic parts using ultrasonic waves: State of the art review

R. Acevedo et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Chemistry, Analytical

A practical guide to rapid-prototyping of PDMS-based microfluidic devices: A tutorial

Giorgio Gianini Morbioli et al.

ANALYTICA CHIMICA ACTA (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of Hydrophilicity, Adhesion Work, and Fluid Flow on Biofilm Formation of PDMS in Microfluidic Systems

Jinling Zhu et al.

ACS APPLIED BIO MATERIALS (2020)

Add to Collection

Article Computer Science, Information Systems

Taguchi Method for Investigation of Ultrasonication-Assisted Dissolution of Acrylonitrile Butadiene Styrene (ABS) Rod Enclosed Within Polydimethylsiloxane (PDMS) Bulk

Pinchuan Chen et al.

IEEE ACCESS (2020)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Additive manufacturing: A review on 3 D printing of metals and study of residual stress, buckling load capacity of strut members

Pritam Anant Pidge et al.

MATERIALS TODAY-PROCEEDINGS (2020)

Add to Collection

Article Computer Science, Information Systems

A Novel Resilient Robot: Kinematic Analysis and Experimentation

Fei Wang et al.

IEEE ACCESS (2020)

Add to Collection

Article Chemistry, Analytical

PolyJet 3D-Printed Enclosed Microfluidic Channels without Photocurable Supports

Andre D. Castiaux et al.

ANALYTICAL CHEMISTRY (2019)

Add to Collection

Editorial Material Computer Science, Information Systems

Integrated design and operation management for enterprise systems

W. J. Zhang et al.

ENTERPRISE INFORMATION SYSTEMS (2019)

Add to Collection

Article Automation & Control Systems

Modelling of the temperature and residual stress fields during 3D printing of polymer composites

A. El Moumen et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Bilayer polymer solar cells prepared with transfer printing of active layers from controlled swelling/de-swelling of PDMS

Anisha Mohapatra et al.

NANO ENERGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Rapid Softlithography Using 3D-Printed Molds

Sajad Razavi Bazaz et al.

ADVANCED MATERIALS TECHNOLOGIES (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Functional 3D Printing for Microfluidic Chips

Gregor Weisgrab et al.

ADVANCED MATERIALS TECHNOLOGIES (2019)

Add to Collection

Article Engineering, Chemical

Roll-To-Roll Screen-Printed Silver Conductors on a Polydimethyl Siloxane Substrate for Stretchable Electronics

Olli-Heikki Huttunen et al.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2019)

Add to Collection

Article Robotics

A Magnetically Controlled Soft Microrobot Steering a Guidewire in a Three-Dimensional Phantom Vascular Network

Sungwoong Jeon et al.

SOFT ROBOTICS (2019)

Add to Collection

Proceedings Paper Computer Science, Artificial Intelligence

Parallelism and Partitioning in Large-Scale GAs using Spark

Laila Alterkawi et al.

PROCEEDINGS OF THE 2019 GENETIC AND EVOLUTIONARY COMPUTATION CONFERENCE (GECCO'19) (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Viscoplastic Matrix Materials for Embedded 3D Printing

Abigail K. Grosskopf et al.

ACS APPLIED MATERIALS & INTERFACES (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Desktop-Stereolithography 3D-Printing of a Poly(dimethylsiloxane)-Based Material with Sylgard-184 Properties

Nirveek Bhattacharjee et al.

ADVANCED MATERIALS (2018)

Add to Collection

Article Biochemical Research Methods

Fabrication of truly 3D microfluidic channel using 3D-printed soluble mold

Kyunghun Kang et al.

BIOMICROFLUIDICS (2018)

Add to Collection

Article Biochemical Research Methods

Throughput enhancement of parallel step emulsifier devices by shear-free and efficient nozzle clearance

Elad Stolovicki et al.

LAB ON A CHIP (2018)

Add to Collection

Article Engineering, Mechanical

An underactuated self-reconfigurable robot and the reconfiguration evolution

Tan Zhang et al.

MECHANISM AND MACHINE THEORY (2018)

Add to Collection

Review Engineering, Electrical & Electronic

3D printed microfluidics and microelectronics

Ryan D. Sochol et al.

MICROELECTRONIC ENGINEERING (2018)

Add to Collection

Review Polymer Science

PDMS with designer functionalities-Properties, modifications strategies, and applications

Marc P. Wolf et al.

PROGRESS IN POLYMER SCIENCE (2018)

Add to Collection

Article Multidisciplinary Sciences

3D printed water-soluble scaffolds for rapid production of PDMS micro-fluidic flow chambers

Tobias Dahlberg et al.

SCIENTIFIC REPORTS (2018)

Add to Collection

Article Materials Science, Biomaterials

3D Printing of PDMS Improves Its Mechanical and Cell Adhesion Properties

Veli Ozbolat et al.

ACS BIOMATERIALS SCIENCE & ENGINEERING (2018)

Add to Collection

Article Materials Science, Biomaterials

3D Printing of PDMS Improves Its Mechanical and Cell Adhesion Properties

Veli Ozbolat et al.

ACS BIOMATERIALS SCIENCE & ENGINEERING (2018)

Add to Collection

Article Chemistry, Physical

A Feasibility Study of Processing Polydimethylsiloxane-Sodium Carboxymethylcellulose Composites by a Low-Cost Fused Deposition Modeling 3D Printer

Paola Calcagnile et al.

MATERIALS (2018)

Add to Collection

Article Chemistry, Multidisciplinary

An On-Chip SiC MEMS Device with Integrated Heating, Sensing, and Microfluidic Cooling Systems

Toan Dinh et al.

ADVANCED MATERIALS INTERFACES (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Enhancement of the surface free energy of PDMS for reversible and leakage-free bonding of PDMS-PS microfluidic cell-culture systems

Ki-Young Song et al.

MICROFLUIDICS AND NANOFLUIDICS (2018)

Add to Collection

Article Chemistry, Physical

Fabrication of Stretchable Circuits on Polydimethylsiloxane (PDMS) Pre-Stretched Substrates by Inkjet Printing Silver Nanoparticles

Jumana M. Abu-Khalaf et al.

MATERIALS (2018)

Add to Collection

Review Engineering, Multidisciplinary

PDMS-Based Microfluidic Devices for Cell Culture

Stefania Torino et al.

INVENTIONS (2018)

Add to Collection

Article Engineering, Electrical & Electronic

Printed microelectrode arrays on soft materials: from PDMS to hydrogels

Nouran Adly et al.

NPJ FLEXIBLE ELECTRONICS (2018)

Add to Collection

Article Engineering, Biomedical

Soft 3D-Printed Phantom of the Human Kidney with Collecting System

Fabian Adams et al.

ANNALS OF BIOMEDICAL ENGINEERING (2017)

Add to Collection

Review Biochemical Research Methods

Non-planar PDMS microfluidic channels and actuators: a review

Yongha Hwang et al.

LAB ON A CHIP (2017)

Add to Collection

Article Biochemical Research Methods

Mimicking arterial thrombosis in a 3D-printed microfluidic in vitro vascular model based on computed tomography angiography data

Pedro F. Costa et al.

LAB ON A CHIP (2017)

Add to Collection

Review Nanoscience & Nanotechnology

Micro/Nanospheres Generation by Fluid-Fluid Interaction Technology: A Literature Review

Lei Lei et al.

RECENT PATENTS ON NANOTECHNOLOGY (2017)

Add to Collection

Article Materials Science, Multidisciplinary

3D reactive inkjet printing of polydimethylsiloxane

Craig Sturgess et al.

JOURNAL OF MATERIALS CHEMISTRY C (2017)

Add to Collection

Article Multidisciplinary Sciences

Self-assembled micro-organogels for 3D printing silicone structures

Christopher S. O'Bryan et al.

SCIENCE ADVANCES (2017)

Add to Collection

Article Multidisciplinary Sciences

Suspended Liquid Subtractive Lithography: One-step generation of 3D channel geometries in viscous curable polymer matrices

D. Helmer et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Multidisciplinary Sciences

Enhanced physicochemical properties of polydimethylsiloxane based microfluidic devices and thin films by incorporating synthetic micro-diamond

Sidra Waheed et al.

SCIENTIFIC REPORTS (2017)

Add to Collection

Article Engineering, Multidisciplinary

Fabrication of Polydimethylsiloxane films with special surface wettability by 3D printing

Zhoukun He et al.

COMPOSITES PART B-ENGINEERING (2017)

Add to Collection

Article Chemistry, Multidisciplinary

3D Printing by Multiphase Silicone/Water Capillary Inks

Sangchul Roh et al.

ADVANCED MATERIALS (2017)

Add to Collection

Article Chemistry, Analytical

Comparing Microfluidic Performance of Three-Dimensional (3D) Printing Platforms

Niall P. Macdonald et al.

ANALYTICAL CHEMISTRY (2017)

Add to Collection

Article Chemistry, Applied

Silicone microreactors for the photocatalytic generation of hydrogen

Alejandra Castedo et al.

CATALYSIS TODAY (2016)

Add to Collection

Editorial Material Computer Science, Information Systems

Design theory and methodology for enterprise systems

W. J. Zhang et al.

ENTERPRISE INFORMATION SYSTEMS (2016)

Add to Collection

Review Biochemical Research Methods

The upcoming 3D-printing revolution in microfluidics

Nirveek Bhattacharjee et al.

LAB ON A CHIP (2016)

Add to Collection

Article Chemistry, Physical

Fabrication of Bendable Circuits on a Polydimethylsiloxane (PDMS) Surface by Inkjet Printing Semi-Wrapped Structures

Jiazhen Sun et al.

MATERIALS (2016)

Add to Collection

Article Chemistry, Analytical

Cytostretch, an Organ-on-Chip Platform

Nikolas Gaio et al.

MICROMACHINES (2016)

Add to Collection

Review Chemistry, Analytical

Mimicking the Kidney: A Key Role in Organ-on-Chip Development

Roberto Paoli et al.

MICROMACHINES (2016)

Add to Collection

Article Materials Science, Biomaterials

3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding

Thomas J. Hinton et al.

ACS BIOMATERIALS SCIENCE & ENGINEERING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti-6Al-4V components

Blanka A. Szost et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Biomaterials

3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding

Thomas J. Hinton et al.

ACS BIOMATERIALS SCIENCE & ENGINEERING (2016)

Add to Collection

Review Engineering, Biomedical

Anti-fouling Coatings of Poly(dimethylsiloxane) Devices for Biological and Biomedical Applications

Hongbin Zhang et al.

JOURNAL OF MEDICAL AND BIOLOGICAL ENGINEERING (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Direct, one-step molding of 3D-printed structures for convenient fabrication of truly 3D PDMS microfluidic chips

Ho Nam Chan et al.

MICROFLUIDICS AND NANOFLUIDICS (2015)

Add to Collection

Article Engineering, Electrical & Electronic

3D printed molds for non-planar PDMS microfluidic channels

Yongha Hwang et al.

SENSORS AND ACTUATORS A-PHYSICAL (2015)

Add to Collection

Article Multidisciplinary Sciences

Writing in the granular gel medium

Tapomoy Bhattacharjee et al.

SCIENCE ADVANCES (2015)

Add to Collection

Article Biochemical Research Methods

PDMS lab-on-a-chip fabrication using 3D printed templates

German Comina et al.

LAB ON A CHIP (2014)

Add to Collection

Article Biochemical Research Methods

Print your own membrane: direct rapid prototyping of polydimethylsiloxane

Tim Femmer et al.

LAB ON A CHIP (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Fabrics coated with lubricated nanostructures display robust omniphobicity

Cicely Shillingford et al.

NANOTECHNOLOGY (2014)

Add to Collection

Article Chemistry, Multidisciplinary

PDMS membranes with tunable gas permeability for microfluidic applications

A. Lamberti et al.

RSC ADVANCES (2014)

Add to Collection

Article Engineering, Manufacturing

Characterization of rapid PDMS casting technique utilizing molding forms fabricated by 3D rapid prototyping technology (RPT)

Attila Bonyar et al.

INTERNATIONAL JOURNAL OF MATERIAL FORMING (2014)

Add to Collection

Article Chemistry, Multidisciplinary

3D Printed Bionic Ears

Manu S. Mannoor et al.

NANO LETTERS (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of mold treatment by solvent on PDMS molding into nanoholes

Celal Con et al.

NANOSCALE RESEARCH LETTERS (2013)

Add to Collection

Article Engineering, Industrial

Toward a resilient manufacturing system

W. J. Zhang et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2011)

Add to Collection

Article Computer Science, Interdisciplinary Applications

The general architecture of adaptive robotic systems for manufacturing applications

Z. M. Bi et al.

ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2010)

Add to Collection

Article Engineering, Electrical & Electronic

Patterning conductive PDMS nanocomposite in an elastomer using microcontact printing

Chao-Xuan Liu et al.

JOURNAL OF MICROMECHANICS AND MICROENGINEERING (2009)

Add to Collection

Article Biochemical Research Methods

A rapid prototyping method for polymer microfluidics with fixed aspect ratio and 3D tapered channels

Andrew W. Browne et al.

LAB ON A CHIP (2009)

Add to Collection

Article Chemistry, Analytical

Low-cost printing of poly(dimethylsiloxane) barriers to define microchannels in paper

Derek A. Bruzewicz et al.

ANALYTICAL CHEMISTRY (2008)

Add to Collection

Article Nanoscience & Nanotechnology

The fabrication of a flexible mold for high resolution soft ultraviolet nanoimprint lithography

Namil Koo et al.

NANOTECHNOLOGY (2008)

Add to Collection

Article Engineering, Electrical & Electronic

Improved mold fabrication for the definition of high quality nanopatterns by soft UV-nanoimprint lithography using diluted PDMS material

Namil Koo et al.

MICROELECTRONIC ENGINEERING (2007)

Add to Collection

Article Chemistry, Multidisciplinary

Click chemistry by microcontact printing

Dorota I. Rozkiewicz et al.

ANGEWANDTE CHEMIE-INTERNATIONAL EDITION (2006)

Add to Collection

Article Engineering, Industrial

Study of shrinkage strains in a stereolithography cured acrylic photopolyrner resin

D Karalekas et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

Article Engineering, Electrical & Electronic

PDMS-based microfluidic devices for biomedical applications

T Fujii

MICROELECTRONIC ENGINEERING (2002)

Add to Collection

Article Biophysics

PDMS device for patterned application of microfluids to neuronal cells arranged by microcontact printing

P Thiebaud et al.

BIOSENSORS & BIOELECTRONICS (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.