☆ 4.3 Article

Corrosion Behaviours of Additively Manufactured Nitrided 17-4 PH Steels in Different Environments

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Experimental and analytical investigation on high chloride-attack resistibility of alloy corrosion-resistant steel Cr10Mo1

Zhiyong Ai et al.

Summary: The electrochemical performance of a new alloy corrosion-resistant steel subjected to chloride attack was evaluated and found to have excellent corrosion resistance. The steel forms a bilayer film structure on its surface, with an inner layer of Cr oxides acting as a protective barrier.

MATERIALS CHEMISTRY AND PHYSICS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

J. R. Jessy Michla et al.

Summary: The effect of nitriding process on the microstructure and mechanical properties of additively manufactured 17-4PH stainless steel is investigated. The nitriding process improves the hardness and surface roughness of the steel, leading to the development of almost equiaxed grain microstructure and the introduction of new precipitates.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)

Add to Collection

Article Materials Science, Coatings & Films

Acceleration effects of rare earths on salt bath nitriding: diffusion kinetics and first-principles calculations

Chang Du et al.

Summary: The study shows that rare earth elements can decrease the diffusion activation energy in salt baths, increase the decomposition rate of active nitrogen atoms, and accelerate nitriding at the atomic level.

SURFACE ENGINEERING (2021)

Add to Collection

Article Engineering, Mechanical

Stress corrosion cracking behavior and mechanism of super 13Cr stainless steel in simulated O2/CO2 containing 3.5 wt% NaCl solution

Sheji Luo et al.

Summary: The stress corrosion cracking behavior of super 13Cr stainless steel in a corrosive environment containing O-2, CO2, and Cl- is influenced by the applied potential, with anode and cathode polarization increasing SCC susceptibility. The mechanism of SCC is related to the applied potentials, with anodic dissolution and hydrogen embrittlement observed at different voltage levels.

ENGINEERING FAILURE ANALYSIS (2021)

Add to Collection

Article Materials Science, Coatings & Films

Enhancement of corrosion protection of AISI 201 austenitic stainless steel in acidic chloride solutions by Ce-doped TiO2 coating

Ghalia A. Gaber et al.

Summary: The electrodeposited Ce-doped TiO2 coatings significantly enhance the corrosion resistance of low-nickel austenitic stainless steel with 8% Mn in acidic chloride solutions. The coatings reduce the corrosion current density and shift the corrosion potential to a more positive value, effectively decreasing the corrosion rate.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Nuclear Science & Technology

Effect of precipitates on hardening of 17-4PH martensitic stainless steel serviced at 300 °C in nuclear power plant

Bing Bai et al.

Summary: When 17-4PH martensitic stainless steel is serviced at 300 degrees C for long term in a nuclear power plant, thermal aging embrittlement and hardening will occur, mainly due to the nucleation and growth of Cu-rich precipitates and Cr-rich precipitates.

ANNALS OF NUCLEAR ENERGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of rare earth modifying inclusions on the pitting corrosion of 13Cr4Ni martensitic stainless steel

Changgang Wang et al.

Summary: This study characterized the pitting corrosion behavior of martensitic stainless steel with and without rare earth modification in NaCl solution. The presence of different inclusions in BASE and REM steels affected the pitting resistance, with REM steel showing both increased susceptibility to pitting nucleation and improved repassivation. The concentration of rare earth elements in the steel matrix influenced the number and size of inclusions, ultimately affecting the overall pitting corrosion resistance.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Multidisciplinary Sciences

Effect of Aging Heat Treatment on Corrosion Behavior and Corrosion Kinetics of 17-4PH Stainless Steel in Artificial Saliva

Onthida Kosasang et al.

Summary: The corrosion behavior of sintered 17-4PH stainless steel samples aged at different conditions in artificial saliva was investigated. Samples aged at 480 degrees Celsius for 1 hour exhibited the highest corrosion resistance, with corrosion kinetics following a bimodal function form rather than a classical power-law function. Pitting corrosion was mainly initiated from existing, isolated pores and further accelerated.

SAINS MALAYSIANA (2021)

Add to Collection

Article Optics

Corrosion behavior of 316L stainless steel manufactured by laser powder bed fusion (L-PBF) in an alkaline solution

M. H. Shaeri Karimi et al.

Summary: This study found that 316L stainless steel processed through L-PBF exhibited better corrosion resistance in alkaline solution and in some cases even outperformed the wrought alloy. The L-PBF processed alloy showed a finer and more uniform microstructure, lower defect density, and lower corrosion current density compared to the wrought counterpart.

OPTICS AND LASER TECHNOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

Impact of the LACKS of Fusion Induced by Additive Manufacturing on the Lubrication of a Gear Flank

Franco Concli et al.

Summary: Additive Manufacturing (AM) technology is gaining popularity for its ability to produce complex geometries, but still faces limitations in terms of achievable surface quality. Research shows that AM processes can promote better lubrication but may expose surface defects that affect structural integrity.

LUBRICANTS (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Investigation of Low-Temperature Liquid Nitriding Conditions for 316 Stainless Steel for Improved Mechanical and Corrosion Response

Nitin Kumar et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of microstructure and manganese sulfides on corrosion resistance of selective laser melted 17-4 PH stainless steel in acidic chloride medium

Michella Alnajjar et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Engineering, Mechanical

Failure analysis of AISI 316L ball valves by salt bath nitriding

Guandong Luo et al.

ENGINEERING FAILURE ANALYSIS (2020)

Add to Collection

Article Engineering, Manufacturing

The modification of corrosion resistance of 17-4PH stainless steel by cutting process

Guoliang Liu et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Passivity of (Mn,Cr)S inclusions in type 304 stainless steel: The role of Cr and the critical concentration for preventing inclusion dissolution in NaCl solution

Masashi Nishimoto et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Short Time Ion Nitriding of AISI 420 Martensitic Stainless Steel to Improve Wear and Corrosion Resistance

Eugenia L. Dalibon et al.

MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Modeling the effect of insoluble corrosion products on pitting corrosion kinetics of metals

Talha Qasim Ansari et al.

NPJ MATERIALS DEGRADATION (2019)

Add to Collection

Article Multidisciplinary Sciences

Electrochemical analysis of the corrosion inhibition effect of trypsin complex on the pitting corrosion of 420 martensitic stainless steel in 2M H2SO4 solution

Roland Tolulope Loto

PLOS ONE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

The Effect of Liquid Nitriding on the Corrosion Resistance of AISI 304 Austenitic Stainless Steel in H2S Environments

Longyi Li et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of simultaneous aging and plasma nitriding on fatigue performance of 17-4 PH stainless steel

Hamidreza Riazi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of plasma nitriding parameters on corrosion performance of 17-4 PH stainless steel

Hamidreza Riazi et al.

CANADIAN METALLURGICAL QUARTERLY (2017)

Add to Collection

Article Nuclear Science & Technology

Investigation of the corrosion behavior of 304L and 316L stainless steels at high-temperature borated and lithiated water

Zhengang Duan et al.

JOURNAL OF NUCLEAR SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of the microstructure on the corrosion behaviour of low-carbon martensitic stainless steel after tempering treatment

V. Vignal et al.

CORROSION SCIENCE (2014)

Add to Collection

Article Materials Science, Multidisciplinary

Localised corrosion and cathodic protection of 17 4PH propeller shafts

T. Bellezze et al.

CORROSION ENGINEERING SCIENCE AND TECHNOLOGY (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and corrosion behaviour of pulsed plasma-nitrided AISI H13 tool steel

Rodrigo L. O. Basso et al.

CORROSION SCIENCE (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Improvement of wear and corrosion resistances of 17-4PH stainless steel by plasma nitrocarburizing

R. L. Liu et al.

MATERIALS & DESIGN (2010)

Add to Collection

Article Materials Science, Coatings & Films

The corrosion and corrosion-wear behaviour of plasma nitrided 17-4PH precipitation hardening stainless steel

M. Esfandiari et al.

SURFACE & COATINGS TECHNOLOGY (2007)

Add to Collection

© Peeref 2019-2024. All rights reserved.