Related references
Note: Only part of the references are listed.
Article
Materials Science, Multidisciplinary
Sheng Huang et al.
Summary: This study investigated the microstructures and mechanical properties of in-situ alloyed Ti41Nb fabricated using laser powder bed fusion (LB-PBF). It was found that a small hatch spacing and fast scanning strategy could minimize porosity and unmelted Nb particle combination. The fabricated blocks had a mesostructure consisting of columnar grains and alternating Nb-poor regions (NPRs), along with extensive iso precipitates. The FCG rate was influenced by the NPR layers and the local slip systems, while the K IC exhibited significant anisotropy due to crack deflection by the NPR/matrix interfaces. Despite its low ductility, the mesostructure-induced toughening mechanism improved the fracture toughness of the alloy.
Article
Nanoscience & Nanotechnology
Qian Xu et al.
Summary: This study investigated the healing behavior, microstructure evolution, and tensile properties of a cast Ti6Al4V alloy with millimeter-scale shrinkage cavities during hot isostatic pressing (HIP). X-ray computed tomography (CT) was used to track the closure process of pores during HIP. The results showed that HIP has the potential to close the shrinkage cavities and the main closure mechanism is plastic deformation. The microstructure analysis revealed the rotation of crystalline lattice and the breakdown of alpha lamellae during HIP. The study also found that HIP treatment improved metallurgical bonding and enhanced the tensile properties.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Materials Science, Multidisciplinary
Mehmood Rashid et al.
Summary: The microstructures and mechanical properties of Ti-6Al-4V fabricated using laser metal deposition (LMD) and electron beam melting (EBM) were compared, showing that LMD samples have superior hardness, strength and work hardening exponent (n), while EBM samples are more ductile. The differences in mechanical behavior of the two samples originate from their distinct dislocation densities within alpha and the relative proportions of Widmanstatten and colony type arrangements of the alpha+beta laths.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
(2022)
Article
Materials Science, Multidisciplinary
Shiliang Zhang et al.
Summary: The research successfully developed a method to add a TiO2 layer on the MAO coating of WE43 alloy, effectively improving the anti-corrosion performance of the coating, reducing the corrosion current density, and proposing the anti-corrosion mechanism of the composite coating.
Article
Physics, Applied
Grzegorz Greczynski et al.
Summary: There is a growing concern within the surface science community regarding the decline in work quality and meaningless chemical bond assignment in XPS articles. This trend could have disastrous consequences for scientific research. To address this, a comprehensive tutorial is offered, providing a step-by-step guide for experimental planning, data acquisition, spectra analysis, and results presentation, with a focus on improving the quality and reliability of XPS data analysis. The tutorial aims to broaden the application of XPS and enhance practitioners' ability to draw meaningful insights from XPS analysis.
JOURNAL OF APPLIED PHYSICS
(2022)
Article
Materials Science, Multidisciplinary
Sheng Huang et al.
Summary: This study investigated the influence of laser power, velocity, and profile on the porosity, inclusion content, and microstructural evolution of in-situ alloyed laser powder bed fusion manufactured Ti34Nb. It found that a specific combination of laser profile, power, velocity, and scanning strategy could result in the formation of an ideal microstructure.
Article
Materials Science, Multidisciplinary
Haifei Lu et al.
Summary: The study revealed that laser shock peening treatment can effectively enhance the hot corrosion resistance of SLMed Ti6Al4V titanium alloy by generating high-density dislocations and nano-twins to enhance the grain boundary effect.
Article
Engineering, Manufacturing
Animesh Kumar Amar et al.
Summary: The paper discusses the development of an analytical model and CFD model for abrasive water slurry jet machining, as well as the experimental investigation of micro-channel formation. The research presents an improved approach of AWSJM by equipping an AWJ machine with a gelatin solution injection setup, leading to efficient energy transfer and increased material removal rate. Experimental results validate the analytical model's accuracy in predicting jet penetration depth.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY
(2021)
Article
Materials Science, Multidisciplinary
Pramod Kumar et al.
Summary: The corrosion resistance of the near-beta Ti-13Nb-13Zr alloy was improved by ultrasonic shot peening treatment, primarily due to grain refinement and the increase in compressive residual stresses in the surface region. Passivation was most prominent after 30 seconds of USSP treatment, decreasing with longer durations.
Article
Nanoscience & Nanotechnology
Lin Tian et al.
Summary: The study found that the monolithic BCC crystalline phase and amorphous phase have high yield strains due to small length scale effects, but undergo negligible post-yield elongation before failure. However, the ductility of the bilaminate composite is significantly higher when the thickness of its amorphous portion is <100 nm.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2021)
Article
Materials Science, Multidisciplinary
Yi Zhang et al.
Summary: TiO2 films were deposited using DC pulsed magnetron sputtering with different sputtering power density, followed by annealing at 600 degrees C to obtain anatase TiO2 films. XPS results showed consistent Ti/O atom ratio in all films. XRD results indicated clear anatase (001) preferred orientation in films deposited with certain SPD. TEM results revealed the microstructure of annealed TiO2 films with anatase (001) orientation. AFM results showed nano-size anatase crystal nuclei with dominated diffusion effect in film growth. During annealing, the nuclei coalesced into large anatase grains maintaining crystal orientation.
Article
Materials Science, Multidisciplinary
Hulin Wu et al.
Summary: The study found that Ti6Al4V alloy experienced oxidation and corrosion during hot salt and hot salt-water vapor tests, with chlorine accelerating oxide growth and leading to both mass gain and mass loss of the alloy. The synergistic effect of oxidation-hot salt-water vapor showed significant damage on the hot end components of titanium alloy during marine service.
Article
Materials Science, Multidisciplinary
Petr Vlcak et al.
Summary: Pre-treatment methods play a crucial role in modifying surface properties and cell response of titanium alloys. Chemical and electrochemical treatments induce significant morphological changes, while surface chemistry dictates changes in contact angle. The presence of native oxides and suboxides contributes to high corrosion stability, while ion sputter etching leads to reduced corrosion resistance.
RESULTS IN PHYSICS
(2021)
Proceedings Paper
Materials Science, Multidisciplinary
Manojkumar Palanivel et al.
Summary: This study focused on developing hydrophobic coatings on commercially pure titanium, using a two-step process involving plasma electrolytic oxidation (PEO) and post-treatment with stearic/myristic acid. The research showed that the type of acid and duration of treatment significantly influenced the hydrophobicity of the surface. The post-acid treatment modified the oxide coatings on the titanium surface, resulting in improved wettability and resistance to corrosion.
MATERIALS TODAY-PROCEEDINGS
(2021)
Review
Materials Science, Multidisciplinary
G. Greczynski et al.
PROGRESS IN MATERIALS SCIENCE
(2020)
Review
Engineering, Manufacturing
Yuvaraj Natarajan et al.
JOURNAL OF MANUFACTURING PROCESSES
(2020)
Article
Engineering, Industrial
Zhirong Liao et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
(2020)
Article
Materials Science, Multidisciplinary
Le Sun et al.
Article
Materials Science, Multidisciplinary
L. Zhang et al.
Article
Engineering, Multidisciplinary
Madhulika Srivastava et al.
Article
Chemistry, Physical
G. Greczynski et al.
APPLIED SURFACE SCIENCE
(2018)
Article
Materials Science, Multidisciplinary
Sudha Joseph et al.
Article
Materials Science, Multidisciplinary
Kang Yuan et al.
Article
Materials Science, Multidisciplinary
C. S. Ramachandran et al.
Article
Materials Science, Multidisciplinary
M. Mohammadi et al.
