☆ 4.7 Article

Surface integrity and tribological behavior of 17Cr2Ni2MoVNb steel under combined carburizing treatment and ultrasonic rolling

SURFACE & COATINGS TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Coatings & Films

Numerical modeling considering initial gradient mechanical properties and experiment verification of residual stress distribution evolution of 12Cr2Ni4A steel generated by ultrasonic surface rolling

Jinyuan Tang et al.

Summary: This paper proposes a numerical model considering initial gradient mechanical properties to predict the residual stress distribution of 12Cr2Ni4A carburized and quenched steel, and a method to calculate the ultrasonic surface rolling coverage based on Hertz contact theory is also proposed. The effects of static load, rolling tool radius, amplitude and feed rate on residual stress distribution are investigated. The simulated results are compared and proved to be in good agreement with the measured results, validating the accuracy of the proposed model.

SURFACE & COATINGS TECHNOLOGY (2023)

Add to Collection

Article Engineering, Mechanical

Surface integrity and bending fatigue behavior of aeronautic gear steel under combined carburized treatment and shot peening

Yalong Zhang et al.

Summary: The carburized treatment combined with shot peening was used to enhance the fatigue behavior of aeronautic gear steel. The study systematically analyzed the surface integrity and fatigue behavior after carburizing and combined treatment. The results showed that the combined treatment increased surface roughness, microhardness, and residual compressive stress, while reducing the average size of ultra-fine grains. The fatigue limit of the samples treated by combined treatment was increased from 720 MPa to 890 MPa compared to carburized samples. Additionally, higher shot peening jet pressure did not necessarily result in better fatigue limit. Residual compressive stress was identified as an important factor influencing fatigue crack propagation mode.

INTERNATIONAL JOURNAL OF FATIGUE (2023)

Add to Collection

Article Engineering, Mechanical

Effect of nano-bainite microstructure and residual stress on friction properties of M50 bearing steel

X. F. Yu et al.

Summary: Through experimental analysis on M50 bearing steel, it was found that nano-bainite structure and residual stress have significant effects on the friction properties of the material.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Preparation and wear resistance of dual-scale structure cemented carbide spherical teeth

Bo Huang et al.

Summary: The dual-scale structured cemented carbide showed excellent comprehensive mechanical properties in drilling operations, with superior impact wear resistance.

VACUUM (2022)

Add to Collection

Article Engineering, Mechanical

Study on the relation between surface integrity and contact fatigue of carburized gears

Xiuhua Zhang et al.

Summary: This study investigates the relation between surface integrity and contact fatigue of gears. The results show that gears with high surface integrity exhibit the highest contact fatigue limit, which is 15.1% higher than gears with carburizing and grinding. Surface hardness, maximum compressive residual stress, and surface roughness are the most significant factors affecting contact fatigue life and fatigue limit. The proposed formulae have reasonable prediction accuracy for fatigue life and fatigue limit.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Engineering, Mechanical

Effects of grain size and protrusion height on the surface integrity generation in the nanogrinding of 6H-SiC

Zhonghuai Wu et al.

Summary: This paper investigates the effects of non-uniform abrasive grains on the deformation and material removal mechanisms of 6H-SiC during nanogrinding using molecular dynamics simulations. The study finds that different sizes of abrasive grains and cutting depths can result in different grinding mechanisms, which in turn affect the plastic deformation of the material.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Optics

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

Xiongfeng Hu et al.

Summary: The effects of DLSH and USR on the material properties and rolling contact fatigue behaviors of 25CrNi2MoV steel were investigated. The results showed that the combination of DLSH and USR improved the surface quality, increased surface hardness, and obtained beneficial surface compressive residual stress. The rolling contact fatigue life of the treated samples was significantly increased compared to the untreated samples.

OPTICS AND LASER TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Coatings & Films

Surface integrity and transmission performance of spiral bevel gears subjected to shot peening: A comparison between concave and convex surfaces

Pengfei Zhu et al.

Summary: Shot peening can effectively enhance the bending fatigue resistance of spiral bevel gears by improving surface integrity parameters. However, the effect mechanism on concave and convex surfaces needs further understanding, and its impact on transmission performance is still controversial.

SURFACE & COATINGS TECHNOLOGY (2022)

Add to Collection

Article Engineering, Mechanical

Microstructure and tribological performances of M50 bearing steel processed by ultrasonic surface rolling

Pei Wang et al.

Summary: This study investigates the use of ultrasonic surface rolling process (USRP) to improve the service life of M50 steel main shaft bearing. The results show that USRP treatment forms a plastic deformation layer, enhances microhardness and residual stress, and improves surface roughness. Compared to untreated samples, USRP samples exhibit lower friction coefficient and wear rate, with a shift in the main wear mechanism towards slight adhesive wear.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Engineering, Mechanical

Rolling contact fatigue properties of ultrasonic surface rolling treated 25CrNi2MoV steel under different lubricant viscosities

Shengguan Qu et al.

Summary: Ultrasonic surface rolling (USR) treatment significantly improves the surface properties of steel, enhances rolling contact fatigue (RCF) life, especially under high lubricant viscosity. The dominant failure mode of samples treated with USR is delamination, indicating the effectiveness of the treatment in reducing fatigue failure.

INTERNATIONAL JOURNAL OF FATIGUE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of ultrasonic surface rolling on fretting wear behaviors of a novel 25CrNi2MoV steel

Yalong Zhang et al.

Summary: Ultrasonic surface rolling (USR) can significantly induce plastic deformation in the material surface layer, resulting in lower coefficient of friction and wear volume. The untreated sample exhibited adhesive wear, while the USR treated samples showed abrasive wear.

MATERIALS LETTERS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Depth-profiling of residual stress and microstructure for austenitic stainless steel surface treated by cavitation, shot and laser peening

Masayoshi Kumagai et al.

Summary: A comparative study was conducted on the effects of different peening techniques on 316L stainless steel, indicating that peening treatment results in surface plastic deformation, residual compressive stress, and increased dislocation density, with varying degrees of impact depending on the peening method used.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

The influence of aluminum on microstructure, mechanical properties and wear performance of Fe-14%Mn-1.05%C manganese steel

S. H. Mousavi Anijdan et al.

Summary: Increasing the Al content in the Fe-14%Mn-1.05%C steel led to larger austenite grain size, reduced carbide precipitation, higher yield strength, hardness, and wear resistance but lower tensile strength, ductility, and energy absorption capability. Wear mechanism was identified as abrasive wear in the form of parallel grooves on the worn surfaces. Additionally, increasing Al content decreased friction coefficient, weight loss, and surface damage.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Surface residual stress and microstructure evolutions of Hastelloy X alloy after severe shot peening

Ming Chen et al.

Summary: Severe shot peening on nickel-based Hastelloy X alloy induced high compressive residual stress, generating a gradient nanostructure layer and significantly increasing surface microhardness.

VACUUM (2021)

Add to Collection

Article Engineering, Mechanical

Investigation on the impact wear behavior of 2.25Cr-1Mo steel at elevated temperature

Xu-dong Chen et al.

Summary: The impact wear test of 2.25Cr-1Mo steel against Gr5C12 alloy was conducted at various temperatures, revealing different interface behaviors and wear mechanisms. As temperature increases, contact force, absorption energy, and wear volume initially rise before decreasing, indicating a modification in surface properties due to higher temperatures. Delamination, plastic deformation, and oxidative wear were identified as major mechanisms, with varying proportions at different temperatures.

WEAR (2021)

Add to Collection

Article Materials Science, Coatings & Films

Surface integrity and wear behavior of 300M steel subjected to ultrasonic surface rolling process

Jiaqiang Dang et al.

Summary: The influences of ultrasonic surface rolling process (USRP) on the surface integrity and wear resistance of 300M steel samples were comprehensively studied. Results indicated that a 10-pass USRP treatment can significantly improve the surface integrity and enhance the wear resistance of 300M steel by about 30.9%. However, the improvements tend to be saturated along with the increase of processing passes.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Effects of ultrasonic surface rolling processing on microstructure and wear properties of high-carbon high-chromium steel

Yong Duan et al.

Summary: This study successfully fractured and dissolved carbides in high-carbon high-chromium steel through ultrasonic surface rolling processing, resulting in a fine microstructure at the surface that improved the wear resistance of the material.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Engineering, Mechanical

The effect of ultrasonic surface rolling process on the fretting fatigue property of GH4169 superalloy

Jing Yang et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Materials Science, Coatings & Films

Effect of shot peening on residual stress distribution and tribological behaviors of 17Cr2Ni2MoVNb steel

Yalong Zhang et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Engineering, Industrial

Effects of ultrasonic nanocrystal surface modification on the surface integrity, microstructure, and wear resistance of 300M martensitic ultra-high strength steel

Weidong Zhao et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Coatings & Films

Experimental study on surface integrity of ultra-high-strength steel by ultrasonic hot rolling surface strengthening

Xiaosheng Luan et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening

Yalong Zhang et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Materials Science, Coatings & Films

Effects of ultrasonic surface rolling processing and plasma nitriding on the fretting wear behavior of Inconel 690TT

Junbiao Liu et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Failure and wear analysis of poly(butylene terephthalate) nanocomposite spur gears

B. H. Soudmand et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Detection of tribolayer in different metals using positron lifetime spectroscopy

Jerzy Dryzek

TRIBOLOGY INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Coatings & Films

Effect of ultrasonic surface rolling on microstructure and rolling contact fatigue behavior of 17Cr2Ni2MoVNb steel

Ya-Long Zhang et al.

SURFACE & COATINGS TECHNOLOGY (2019)

Add to Collection

Article Engineering, Mechanical

Constitutive behavior and microstructural evolution in ultrasonic vibration assisted deformation of ultrathin superalloy sheet

B. Meng et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)

Add to Collection

Article Materials Science, Coatings & Films

Effects of conventional, severe, over, and re-shot peening processes on the fatigue behavior of mild carbon steel

Erfan Maleki et al.

SURFACE & COATINGS TECHNOLOGY (2018)

Add to Collection

Article Engineering, Mechanical

The wear and fatigue behaviours of hollow head & sodium filled engine valve

Fuqiang Lai et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Chemistry, Physical

Roles of surface coverage increase and re-peening on properties of AISI 1045 carbon steel in conventional and severe shot peening processes

Erfan Maleki et al.

SURFACES AND INTERFACES (2018)

Add to Collection

Article Materials Science, Coatings & Films

Microstructure related enhancement in wear resistance of tool steel AISI D2 by applying laser heat treatment followed by ultrasonic impact treatment

D. A. Lesyk et al.

SURFACE & COATINGS TECHNOLOGY (2017)

Add to Collection

Article Materials Science, Coatings & Films

Microstructure and surface properties of 17-4PH stainless steel by ultrasonic surface rolling technology

Qinglong Zhang et al.

SURFACE & COATINGS TECHNOLOGY (2017)

Add to Collection

Article Materials Science, Coatings & Films

Ultrasonic studies of texture inhomogeneities in pressure vessel steel subjected to ultrasonic impact treatment and shock compression

O. I. Zaporozhets et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Add to Collection

Article Mechanics

Evolution of residual stress during fatigue crack growth in an aluminium specimen with a bonded crack retarder

Abdul Khadar Syed et al.

COMPOSITE STRUCTURES (2014)

Add to Collection

Article Engineering, Mechanical

An evaluation of shot peening, residual stress and stress relaxation on the fatigue life of AISI 4340 steel

MAS Torres et al.

INTERNATIONAL JOURNAL OF FATIGUE (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.