☆ 4.6 Article

Debonding quantification in adhesive bonded joints by the inverse finite element method

SMART MATERIALS AND STRUCTURES (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

Towards a stochastic inverse Finite Element Method: A Gaussian Process strain extrapolation

Dario Poloni et al.

Summary: The inverse Finite Element Method (iFEM) is used to reconstruct the full-field displacement on beam or shell structures using a network of strain sensors. A Gaussian Process is proposed as a strain pre-extrapolation and interpolation technique to provide strain values and compute the uncertainty on the reconstructed displacement field.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2023)

Add to Collection

Proceedings Paper Engineering, Civil

Crack Size Estimation with an Inverse Finite Element Model

Daniele Oboe et al.

Summary: The inverse Finite Element Method (iFEM) is a model-based technique that calculates the displacement field of a structure using strain measurements and geometric discretization. It has various applications in Structural Health Monitoring (SHM), mainly focused on damage detection and localization. This study proposes a novel iFEM approach to estimate damage size without the need for a database of damage models. The technique systematically increases the damage size until the strain discrepancy between experimental measurements and numerical strain reconstruction is minimized.

EUROPEAN WORKSHOP ON STRUCTURAL HEALTH MONITORING (EWSHM 2022), VOL 1 (2023)

Add to Collection

Article Engineering, Chemical

Investigation into the mechanical behavior of a polymer optical fiber embedded in a structural adhesive

J. Weiland et al.

Summary: This study demonstrates a novel approach for Structural Health Monitoring (SHM) of adhesively bonded joints using integrated Polymer Optical Fibers (POF). The results from numerical and experimental analysis show a linear correlation between strain inside the POF and strain of the surrounding adhesive. The failure analysis reveals a highly ductile behavior of the POF cladding material and the interface between the POF core and annular cladding.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2022)

Add to Collection

Article Engineering, Mechanical

Fatigue crack growth analysis in composite bonded joints by back face distributed strain sensing and comparison with X-ray microtomography

A. Bernasconi et al.

Summary: This study analyzes the fatigue crack growth in composite, single lap bonded joints using back face distributed strain sensing and optical backscatter reflectometry. The proposed technique can accurately detect crack initiation and measure crack growth in good agreement with observations.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Engineering, Chemical

A methodology for detection of crack initiation in adhesively bonded joints under constant and variable amplitude fatigue loading

M. Gastens et al.

Summary: This study presents a new approach for detecting crack initiation in adhesively bonded single lap joints subjected to constant and variable amplitude fatigue loading using the backface strain method. The results showed a converging-diverging trend in strain amplitude curves under constant amplitude loading, which correlated well with the onset of crack initiation. The methodology was also successfully demonstrated on joints subjected to variable amplitude loading using an additional farfield strain gauge for detecting crack initiation.

JOURNAL OF ADHESION (2022)

Add to Collection

Article Engineering, Multidisciplinary

Polynomial Chaos-Kriging metamodel for quantification of the debonding area in large wind turbine blades

Bruna Pavlack et al.

Summary: This study investigates the performance of a data-driven methodology for quantifying damage using a metamodel obtained from the Polynomial Chaos-Kriging method. The severity of debonding damage in a wind turbine blade is quantified as a function of a damage index. The metamodel is validated with different damage conditions and shows promising results in capturing the trend of damage severity.

STRUCTURAL HEALTH MONITORING-AN INTERNATIONAL JOURNAL (2022)

Add to Collection

Article Instruments & Instrumentation

Acoustic emission-based monitoring of fatigue damage in CFRP-CFRP adhesively bonded joints

M. Carboni et al.

Summary: Adhesively bonded joints are commonly used in modern structures, but they can suffer from local debonding and catastrophic failures. This research examines the use of structural health monitoring and non-destructive testing procedures to evaluate the integrity of adhesively bonded joints under constant fatigue loading. The results show that acoustic emission-based monitoring can effectively identify and characterize the development of fatigue damage in these joints.

INSIGHT (2022)

Add to Collection

Review Mechanics

Damage monitoring methods for fiber-reinforced polymer joints: A review

Wencai Li et al.

Summary: This paper presents a comprehensive review on damage monitoring methods for fiber-reinforced polymer joints in composite structures. The methods are classified into intrinsic sensing and extrinsic sensing, and their applications in detecting damage type, location, and severity are discussed. The paper also summarizes novel methods, significant results, current trends, and challenges in this field, and recommends further research efforts.

COMPOSITE STRUCTURES (2022)

Add to Collection

Article Engineering, Mechanical

Physics-based strain pre-extrapolation technique for inverse Finite Element Method

Daniele Oboe et al.

Summary: The inverse Finite Element Method (iFEM) is a model-based technique that uses an optimized strain sensor network to compute the displacement field of a structure. By using strain pre-extrapolation techniques, the strain values in areas without physical sensors can be predicted, with support from the physical knowledge of the discontinuity and its analytical stress formulation, improving the field reconstruction of iFEM.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2022)

Add to Collection

Article Engineering, Mechanical

Distributed fibre optic monitoring of mode I fatigue crack propagation in adhesive bonded joints and comparison with digital image correlation

R. A. A. Lima et al.

Summary: The feasibility of using Optical Backscatter Reflectometry as a backface strain monitoring method for bonded joints subjected to mode I fatigue crack propagation was investigated. Visual evaluation and Digital Image Correlation methods were employed to track the crack-tip position and the onset of plasticisation in the adhesive, respectively. The relationship between changes in the optical fibre measurements and crack propagation was compared.

THEORETICAL AND APPLIED FRACTURE MECHANICS (2022)

Add to Collection

Article Mechanics

Comparison of strain pre-extrapolation techniques for shape and strain sensing by iFEM of a composite plate subjected to compression buckling

Daniele Oboe et al.

Summary: The iFEM is a model-based technique for structural shape sensing using experimentally acquired input strain data, making it applicable for composite materials monitoring. In experiments, SEA and polynomial fitting are used to pre-extrapolate the strain field of the entire plate, and sensitivity analysis and laser measurements are used to validate the iFEM displacement reconstruction capability.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Engineering, Multidisciplinary

Fatigue damage diagnosis and prognosis of an aeronautical structure based on surrogate modelling and particle filter

Demetrio Cristiani et al.

Summary: The degradation of engineering systems due to fatigue crack growth is a key issue, with uncertainty sources in both the item itself and the physical degradation process variability. Particle filters provide a Bayesian framework for approximating system degradation state, but face challenges in real-time operation due to computational power requirements. A comprehensive particle filter framework is proposed to address fatigue crack growth uncertainty sources and computational burden issue, incorporating artificial neural networks-based surrogate modelling to improve efficiency.

STRUCTURAL HEALTH MONITORING-AN INTERNATIONAL JOURNAL (2021)

Add to Collection

Article Engineering, Mechanical

Shape sensing and damage identification with iFEM on a composite structure subjected to impact damage and non-trivial boundary conditions

Luca Colombo et al.

Summary: The inverse Finite Element Method (iFEM) is a valuable tool for shape sensing and damage identification in structural health monitoring frameworks. This method calculates displacement fields and strain fields based on discrete strain measurements in the structure without prior knowledge of material properties or loading conditions.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2021)

Add to Collection

Article Chemistry, Analytical

Shape Sensing of a Complex Aeronautical Structure with Inverse Finite Element Method

Daniele Oboe et al.

Summary: The inverse Finite Element Method (iFEM) is gaining attention for shape sensing due to its independence from material properties and external load. Proper definition of model geometry, boundary conditions, and optimized sensor networks to acquire strain field are required for complex structures. A simplified iFEM model with reduced geometrical complexity and tuned boundary conditions is proposed to handle structures with partial sensor application, showing effectiveness in aeronautical structures with experimentally acquired strain measurements.

SENSORS (2021)

Add to Collection

Article Engineering, Multidisciplinary

Development of an integrated sacrificial sensor for damage detection and monitoring in composite materials and adhesively bonded joints

G. Olafsson et al.

Summary: This study introduces a novel embedded sensor for detecting damage within adhesively bonded joints. The sensor operates by detecting changes in electrical resistance and has shown potential for load monitoring and cycle counting. The sensor does not compromise the structural performance of materials and provides timely failure indication for effective repair.

STRUCTURAL HEALTH MONITORING-AN INTERNATIONAL JOURNAL (2021)

Add to Collection

Article Engineering, Mechanical

Experimental analysis of mode I crack propagation in adhesively bonded joints by optical backscatter reflectometry and comparison with digital image correlation

R. A. A. Lima et al.

Summary: In this study, the relationship between Optical Backscatter Reflectometry-based backface strain sensing and adhesive damage was investigated using double cantilever beam specimens. It was found that backface strain sensing allowed for the identification of plastic deformations ahead of the crack-tip, which opens up new possibilities for fatigue crack monitoring and in-service measurements.

THEORETICAL AND APPLIED FRACTURE MECHANICS (2021)

Add to Collection

Article Mechanics

Structural health monitoring of a CFRP structural bonded repair by using a carbon nanotube modified adhesive film

Xoan F. Sanchez-Romate et al.

Summary: The carbon nanotube (CNT) doped adhesive film has been shown to have good crack-sensing capabilities, with no negative impact on mechanical performance, and an increase in electrical resistance during crack propagation and adhesive deformation processes.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Engineering, Mechanical

A smoothed iFEM approach for efficient shape-sensing applications: Numerical and experimental validation on composite structures

Adnan Kefal et al.

Summary: The smoothed inverse finite element method (iFEM((s))) combines the inverse finite element method (iFEM) and the smoothing element analysis (SEA) for real-time displacement field reconstruction using strain-sensor measurements. This method is validated for shape sensing in multilayered composite and sandwich structures. By incorporating refined zigzag theory (RZT), the approach accurately models through-the-thickness displacement distributions and accurately predicts structural shapes.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2021)

Add to Collection

Article Engineering, Mechanical

Structural health monitoring of aerospace sandwich structures via strain measurements along zero-strain trajectories

Thomas Bergmayr et al.

Summary: This paper investigates a strain-based structural health monitoring method for damage detection and localization in composite sandwich structures, using numerical and experimental analysis to demonstrate its effectiveness for edge structure.

ENGINEERING FAILURE ANALYSIS (2021)

Add to Collection

Article Engineering, Chemical

Damage detection in adhesively bonded single lap joints by using backface strain: Proposing a new position for backface strain gauges

M. Z. Sadeghi et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2020)

Add to Collection

Article Engineering, Marine

Dent damage identification in stiffened cylindrical structures using inverse Finite Element Method

Mingyang Li et al.

OCEAN ENGINEERING (2020)

Add to Collection

Article Instruments & Instrumentation

Fatigue crack growth identification in bonded joints by using carbon nanotube doped adhesive films

Xoan F. Sanchez-Romate et al.

SMART MATERIALS AND STRUCTURES (2020)

Add to Collection

Article Mechanics

Evaluation of infrared thermography methods for analysing the damage behaviour of adhesively bonded repair solutions

U. Martens et al.

COMPOSITE STRUCTURES (2020)

Add to Collection

Article Engineering, Marine

Structural health monitoring of an offshore wind turbine tower using iFEM methodology

Mingyang Li et al.

OCEAN ENGINEERING (2020)

Add to Collection

Article Green & Sustainable Science & Technology

Manufacturing variability drives significant environmental and economic impact: The case of carbon fiber reinforced polymer composites in the aerospace industry

Alexander van Grootel et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Add to Collection

Article Engineering, Chemical

Advanced ultrasonic NDT for weak bond detection in composite-adhesive bonded structures

Bengisu Yilmaz et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Impact area and debonding line detection assessment by cross-correlation analysis and distributed sensing

M. Ciminello et al.

OPTICAL FIBER TECHNOLOGY (2020)

Add to Collection

Article Engineering, Aerospace

Structural health monitoring of an adhesively bonded CFRP aircraft fuselage by ultrasonic Lamb Waves

J. Weiland et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART G-JOURNAL OF AEROSPACE ENGINEERING (2020)

Add to Collection

Article Mechanics

Stringer debonding edge detection employing fiber optics by combined distributed strain profile and wave scattering approaches for non-model based SHM

Monica Ciminello et al.

COMPOSITE STRUCTURES (2019)

Add to Collection

Article Engineering, Mechanical

Definition of a load adaptive baseline by inverse finite element method for structural damage identification

Luca Colombo et al.

MECHANICAL SYSTEMS AND SIGNAL PROCESSING (2019)

Add to Collection

Article Engineering, Marine

An efficient curved inverse-shell element for shape sensing and structural health monitoring of cylindrical marine structures

Adnan Kefal

OCEAN ENGINEERING (2019)

Add to Collection

Article Engineering, Chemical

Structural health monitoring of an adhesive disbond through electromechanical impedance spectroscopy

William Roth et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2017)

Add to Collection

Article Engineering, Chemical

Strain Profile Measurement for Structural Health Monitoring of Woven Carbon-fiber Reinforced Polymer Composite Bonded joints by Fiber Optic Sensing Using an Optical Backscatter Reflectometer

Andrea Bernasconi et al.

JOURNAL OF ADHESION (2016)

Add to Collection

Article Engineering, Chemical

Fatigue Crack Growth Monitoring in Composite Bonded Lap Joints by a Distributed Fibre Optic Sensing System and Comparison with Ultrasonic Testing

A. Bernasconi et al.

JOURNAL OF ADHESION (2016)

Add to Collection

Article Engineering, Marine

Displacement and stress monitoring of a Panamax containership using inverse finite element method

Adnan Kefal et al.

OCEAN ENGINEERING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Structural health monitoring of a composite skin-stringer assembly using within-the-bond strategy of guided wave propagation

Mohammad H. Sherafat et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Engineering, Multidisciplinary

A quadrilateral inverse-shell element with drilling degrees of freedom for shape sensing and structural health monitoring

Adnan Kefal et al.

ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2016)

Add to Collection

Article Instruments & Instrumentation

An inverse finite element method for beam shape sensing: theoretical framework and experimental validation

Marco Gherlone et al.

SMART MATERIALS AND STRUCTURES (2014)

Add to Collection

Article Mechanics

Analysis of adhesively bonded repairs in composites: Damage detection and prognosis

M. A. Caminero et al.

COMPOSITE STRUCTURES (2013)

Add to Collection

Article Engineering, Multidisciplinary

Damage monitoring and analysis of composite laminates with an open hole and adhesively bonded repairs using digital image correlation

M. A. Caminero et al.

COMPOSITES PART B-ENGINEERING (2013)

Add to Collection

Article Engineering, Mechanical

A study on fatigue crack propagation in thick composite adhesively bonded joints

A. Bernasconi et al.

INTERNATIONAL JOURNAL OF FATIGUE (2013)

Add to Collection

Article Engineering, Chemical

Development of a proof test for through-life monitoring of bond integrity in adhesively bonded repairs to aircraft structure

Alan Baker et al.

INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES (2012)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Monitoring of fatigue crack growth in composite adhesively bonded joints using Fiber Bragg Gratings

Andrea Bernasconi et al.

11TH INTERNATIONAL CONFERENCE ON THE MECHANICAL BEHAVIOR OF MATERIALS (ICM11) (2011)

Add to Collection

Article Engineering, Chemical

Fatigue initiation in adhesively-bonded single-lap joints

A. Graner Solana et al.

JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2007)

Add to Collection

Review Engineering, Aerospace

Fibre reinforced composites in aircraft construction

C Soutis

PROGRESS IN AEROSPACE SCIENCES (2005)

Add to Collection

© Peeref 2019-2024. All rights reserved.