☆ 4.7 Article

Investigation on fine particle deposition characteristics in narrow rectangular channel based on Eulerian-Lagrangian method

POWDER TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Chemical

Thermal-hydraulic and particle deposition analysis of supercritical CO2 in different tubes

Shang Mao et al.

Summary: The thermal-hydraulic and particle deposition characteristics of supercritical CO2 (SCO2) in different tubes were numerically investigated. It was found that the semi-circular tube exhibited the best heat transfer performance and could effectively alleviate the buoyancy effect. The corners of the semi-circular and square tubes should be further optimized to prevent excessive temperatures. The particle deposition efficiency varied with particle size, mass flux, and heat flux, indicating that flow channels should be further optimized for heat exchangers using SCO2 as working fluid.

POWDER TECHNOLOGY (2023)

Add to Collection

Article Thermodynamics

Experimental investigation of temperature and hydrodynamics on CaCO3 fouling during convective heat transfer and subcooled flow boiling

Sadaf Rahimi et al.

Summary: Deposit formation in heat exchangers is an undesirable process that can reduce their performance and efficiency. This research investigated the impact of fluid bulk temperature (Tb) on the deposition of CaCO3 solution under convective heat transfer and subcooled flow boiling conditions. The study found that Tb significantly influenced the mechanism of deposit formation, changing the fouling resistance curve and crystal type of the deposit layer. The results also showed that heat flux and fluid flow rate had different effects on fouling rate depending on Tb and heat flux levels.

APPLIED THERMAL ENGINEERING (2023)

Add to Collection

Article Thermodynamics

Study on mechanical stress of semicircular and rectangular channels in printed circuit heat exchangers

Zirui Xu et al.

Summary: In this study, a simplified mechanical stress analysis method for PCHE was proposed to improve its safety under high pressure operation. By optimizing the channel shape, the mechanical stress of PCHE can be reduced, leading to a more compact design and safe operation.

ENERGY (2022)

Add to Collection

Article Chemistry, Physical

Numerical modeling on heat transfer of supercritical water in cooled horizontal circular tube

Shang Mao et al.

Summary: This paper investigates the cooling heat transfer characteristics of supercritical water in horizontal tubes using numerical simulation. The effects of heat flux, mass flux, tube diameter, and buoyancy on heat transfer performance are revealed, and two models are validated against experiments.

JOURNAL OF SUPERCRITICAL FLUIDS (2022)

Add to Collection

Article Thermodynamics

Experimental study on fouling inhibition characteristics of a variable frequency electromagnetic field on the CaCO3 fouling of a heat transfer surface

Yandong Liang et al.

Summary: Forced convective heat transfer and CaCO3 deposition experiments were conducted to investigate the fouling inhibition characteristics of a variable frequency electromagnetic field. The results showed that the electromagnetic field effectively inhibited the CaCO3 fouling deposition and decreased the growth rate of fouling. It also reduced the conductivity of the test fluid and promoted the crystallization of CaCO3 in aragonite, resulting in easily removable soft fouling. An evaluation model was proposed to better define the fouling inhibition effect of the variable frequency electromagnetic field.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2022)

Add to Collection

Article Chemistry, Physical

Numerical investigation on flow and thermal performance of supercritical CO2 in a horizontal ribbed tube

Shang Mao et al.

Summary: The thermal performance of supercritical carbon dioxide in horizontal ribbed tubes has been investigated through numerical simulation. Three types of ribs were studied to understand their effects on heat transfer. The results show that the triangular ribbed tubes can significantly enhance the heat transfer coefficient and reduce wall temperature. However, circular ribbed tubes demonstrate the best performance from the viewpoint of performance evaluation criteria. Moreover, the rib configuration promotes the transition of the flow field, leading to improved heat transfer. Finally, small rib size and medium pitch further enhance the turbulent heat transfer of supercritical CO2.

JOURNAL OF SUPERCRITICAL FLUIDS (2022)

Add to Collection

Article Thermodynamics

Predicting heat transfer and flow features of supercritical CO2 in printed circuit heat exchangers with novel wavy minichannels

Morteza Khoshvaght-Aliabadi et al.

Summary: This study investigates the performance of non-uniform wavy minichannels using supercritical carbon dioxide as the working fluid. The results show that the proposed structures for the wavy minichannels can increase the heat transfer coefficient under the given operating conditions. Replacing the conventional wavy minichannel with shorter wavelengths at the upstream significantly enhances the heat transfer in both cooling and heating modes.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2022)

Add to Collection

Article Thermodynamics

Development of subcooled wall boiling model considering bubble sliding in narrow rectangular channel

Mingjun Wang et al.

Summary: This paper focuses on the development of a wall boiling model which considers the influence of bubble sliding in describing wall boiling phenomena. The developed model has been validated through experiments and shows better performance in narrow rectangular channels.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2022)

Add to Collection

Article Nuclear Science & Technology

A coupled model of corrosion of the steam generator heat transfer tube

Weibing Wang et al.

Summary: In this paper, a mechanism model of the coupling of ion migration and fluid dynamics of the heat transfer tube on the secondary side of the steam generator is established. The accuracy of the model was verified, and the sensitivity of the migration process of impurity ions to metal corrosion was analyzed and discussed.

NUCLEAR ENGINEERING AND DESIGN (2022)

Add to Collection

Article Thermodynamics

Migration-deposition coupling characteristics and influence of corrosion products on heat transfer in steam generators

Defang Mu et al.

Summary: This study aimed to predict the distribution of deposits on the surface of heat transfer tubes and assess its influence on heat transfer characteristics. A comprehensive model was established to simulate the fouling characteristics of steam generators. The results showed that fouling had an evident effect on the overall heat transfer efficiency and distribution of steam generators.

APPLIED THERMAL ENGINEERING (2022)

Add to Collection

Article Thermodynamics

Modeling of heat transfer of supercritical water in helical finned double pipe

Shang Mao et al.

Summary: This study numerically simulated the flow and heat transfer behavior of supercritical water in a horizontal double pipe with helical fins, revealing peak heat transfer coefficients under specific conditions. Factors affecting heat transfer performance include buoyancy, hot fluid temperature, mass flux, and shape factor.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

A CFD study of particle deposition in three-dimensional heat exchange channel based on an improved deposition model

Hao Lu et al.

Summary: This study investigates particle deposition in a heat exchange channel with surface ribs, identifying flow structures, deposition locations, and deposition efficiency, all influenced by important parameters such as particle diameter and air flow velocity. Main mechanisms for particle deposition include turbulent flow induced by the ribs, secondary flow, particle rebound, and gravitational settling.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

CFD aided design and analysis of a precooler with zigzag channels for supercritical CO2 power cycle

Muhammed Saeed et al.

Summary: The study suggests that choosing smaller design point values for CO2 channel mass flow rates can significantly reduce pressure losses, but may result in undesirable temperature profiles; higher channel mass flow rates can avoid pinch points in the precooler, but lead to compact designs with poor hydraulic performance; using a sandwiched channel configuration can substantially improve the hydraulic performance of the cold side without affecting the thermal characteristics of the precooler.

ENERGY CONVERSION AND MANAGEMENT (2021)

Add to Collection

Article Engineering, Chemical

Simulation of particle fouling characteristics with improved modeling on two different tubes

Zhiming Xu et al.

Summary: This paper studied the fouling characteristics of micron-scale magnesium oxide particles in circular and converging-diverging tubes. The simulation results showed that the fouling resistance of the converging-diverging tube was smaller than that of the circular tube.

POWDER TECHNOLOGY (2021)

Add to Collection

Article Thermodynamics

Experimental and numerical investigation on particulate fouling characteristics of vortex generators with a hole

Zhimin Han et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Engineering, Chemical

Three-way coupling of fine particle deposition behavior on a rib-roughened surface

Wenpeng Hong et al.

POWDER TECHNOLOGY (2020)

Add to Collection

Article Engineering, Chemical

Experimental and numerical approach to resolve particle deposition on dimpled heat transfer surfaces locally and temporally

Hannes Deponte et al.

CHEMICAL ENGINEERING SCIENCE (2020)

Add to Collection

Article Thermodynamics

Deposition characteristics of particles in inclined heat exchange channel with surface ribs

Hao Lu et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Thermodynamics

Numerical simulation and experimental study of the growth characteristics of particulate fouling on pipe heat transfer surface

Ning Zhang et al.

HEAT AND MASS TRANSFER (2019)

Add to Collection

Article Thermodynamics

Numerical study of particulate fouling characteristics in a rectangular heat exchange channel

Zhiming Xu et al.

APPLIED THERMAL ENGINEERING (2019)

Add to Collection

Article Nuclear Science & Technology

Modeling heat transfer through corrosion product deposits on fuel rods in pressurized water reactors

D. Y. Yeo et al.

NUCLEAR ENGINEERING AND DESIGN (2019)

Add to Collection

Article Nuclear Science & Technology

Modeling of corrosion-induced blockages on radiation heat transfer by using RELAP5-3D

Jivan Khatry et al.

PROGRESS IN NUCLEAR ENERGY (2019)

Add to Collection

Article Thermodynamics

The deposition characteristics of micron particles in heat exchange pipelines

Zhimin Han et al.

APPLIED THERMAL ENGINEERING (2019)

Add to Collection

Review Astronomy & Astrophysics

Study on the method of nuclear power operation and analysis of movement and deposition of accident particles

Zhou Tao et al.

SCIENTIA SINICA-PHYSICA MECHANICA & ASTRONOMICA (2019)

Add to Collection

Article Energy & Fuels

Parametric study on fouling mechanism and heat transfer characteristics of tube bundle heat exchangers for reducing fouling considering the deposition and removal mechanisms

Song-Zhen Tang et al.

FUEL (2018)

Add to Collection

Article Thermodynamics

Exploration of nanofluid pool boiling and deposition on a horizontal cylinder in Eulerian and Lagrangian frames

Mostafa Mahdavi et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)

Add to Collection

Article Energy & Fuels

Fouling characteristics analysis and morphology prediction of heat exchangers with a particulate fouling model considering deposition and removal mechanisms

Song-Zhen Tang et al.

FUEL (2017)

Add to Collection

Article Thermodynamics

Parameter study on the fouling characteristics of the H-type finned tube heat exchangers

Fei-Long Wang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2017)

Add to Collection

Article Engineering, Chemical

Lattice Boltzmann method and RANS approach for simulation of turbulent flows and particle transport and deposition

H. Sajjadi et al.

PARTICUOLOGY (2017)

Add to Collection

Article Engineering, Chemical

Numerical study on deposition of particles in a 90° bend in the presence of swirling flow using Eulerian-Lagrangian method

Akbar Arsalanloo et al.

POWDER TECHNOLOGY (2017)

Add to Collection

Article Engineering, Chemical

A two-way couple of Eulerian-Lagrangian model for particle transport with different sizes in an obstructed channel

Mahla Maskaniyan et al.

POWDER TECHNOLOGY (2017)

Add to Collection

Article Thermodynamics

Experimental and numerical investigation on particle deposition in a compact heat exchanger

S. Baghdar Hosseini et al.

APPLIED THERMAL ENGINEERING (2017)

Add to Collection

Article Construction & Building Technology

Simulations of indoor airflow and particle dispersion and deposition by the lattice Boltzmann method using LES and RANS approaches

H. Sajjadi et al.

BUILDING AND ENVIRONMENT (2016)

Add to Collection

Article Engineering, Chemical

Eulerian-Lagrangian modeling of solid particle behavior in a square cavity with several pairs of heaters and coolers inside

Faroogh Garoosi et al.

POWDER TECHNOLOGY (2015)

Add to Collection

Article Engineering, Chemical

Sticking/rebound criterion for collisions of small adhesive particles: Effects of impact parameter and particle size

Sheng Chen et al.

POWDER TECHNOLOGY (2015)

Add to Collection

Article Nuclear Science & Technology

Experimental studies on single-phase flow and heat transfer in a narrow rectangular channel

Jian Ma et al.

NUCLEAR ENGINEERING AND DESIGN (2011)

Add to Collection

Article Engineering, Chemical

Application of a modified Eulerian model to study the particle deposition on a vertical surface in turbulent flow

M. Abdolzadeh et al.

POWDER TECHNOLOGY (2011)

Add to Collection

Article Engineering, Chemical

An integrated theoretical fouling model for convective heating surfaces in coal-fired boilers

Yadi Pan et al.

POWDER TECHNOLOGY (2011)

Add to Collection

Article Engineering, Chemical

Rebound characteristics for 50-μm particles impacting a powdery deposit

M. C. van Beek et al.

POWDER TECHNOLOGY (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.