4.5 Article

The Effect of the Process Parameters on the Growth Rate and Composition of the Anti Scratch Films Deposited from TEOS by AP-PECVD on Polycarbonate

Related references

Note: Only part of the references are listed.
Article Engineering, Chemical

The Effect of the Process Parameters on the Composition and Properties of Silica-Like Films Deposited by Atmospheric Pressure PECVD in the System TEOS-He-O2

Anastasia S. Bil et al.

Summary: This paper reports on a study of an atmospheric pressure plasma enhanced chemical vapor deposition process using a simple dielectric barrier discharge and a low frequency high voltage generator. The authors investigated the effect of deposition parameters on the properties of silica-like layers grown from a TEOS/He/O-2 system. The results show that deposition temperature and electrical power absorbed in plasma are critical parameters in determining the characteristics of the deposited films. The study provides insights into achieving high growth rates of high quality films.

PLASMA CHEMISTRY AND PLASMA PROCESSING (2022)

Article Engineering, Electrical & Electronic

Improved abrasion resistance of silica-based CVD thin films on polycarbonate substrates for automotive applications

Sae Tanaka et al.

Summary: By changing the carrier gas from He to Ar, the abrasion resistance and adhesion strength of the silica-based thin film were improved, making it suitable for vehicle window glass replacements. The adhesion strength between the film and substrate was likely enhanced by the etching effect of the Ar plasma on the primer.

JOURNAL OF VACUUM SCIENCE & TECHNOLOGY B (2021)

Article Materials Science, Characterization & Testing

Scratch behavior of polycarbonate by Rockwell C diamond indenter under progressive loading

Ming Liu et al.

POLYMER TESTING (2020)

Review Chemistry, Applied

Recent progress of functional coating materials and technologies for polycarbonate

Namil Kim

JOURNAL OF COATINGS TECHNOLOGY AND RESEARCH (2017)

Article Materials Science, Coatings & Films

Tetrakis(trimethylsilyloxy)silane for nanostructured SiO2-like films deposited by PECVD at atmospheric pressure

J. Schaefer et al.

SURFACE & COATINGS TECHNOLOGY (2016)

Article Materials Science, Multidisciplinary

Deposition of silicon oxide coatings by atmospheric pressure plasma jet for oxygen diffusion barrier applications

Haitao Zhang et al.

THIN SOLID FILMS (2016)

Review Materials Science, Ceramics

Mechanical properties of sol-gel coatings on polycarbonate: a review

Nicolas Le Bail et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2015)

Article Materials Science, Ceramics

The effect of TEOS plasma parameters on the silicon dioxide deposition mechanisms

Marzieh Abbasi-Firouzjah et al.

JOURNAL OF NON-CRYSTALLINE SOLIDS (2013)

Article Instruments & Instrumentation

Refractive index changes in amorphous SiO2 (silica) by swift ion irradiation

O. Pena-Rodriguez et al.

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION B-BEAM INTERACTIONS WITH MATERIALS AND ATOMS (2012)

Review Materials Science, Multidisciplinary

An Overview of the Scratch Resistance of Automotive Coatings: Exterior Clearcoats and Polycarbonate Hardcoats

Christopher Seubert et al.

COATINGS (2012)

Article Materials Science, Ceramics

TiO2-SiO2 hard coating on polycarbonate substrate by microwave assisted sol-gel technique

Martina Dinelli et al.

JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY (2011)

Article Engineering, Mechanical

Effect of distance from the support on the penetration mechanism of clamped circular polycarbonate armor plates

Qasim H. Shah et al.

INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2008)

Article Materials Science, Multidisciplinary

A study towards improving mechanical properties of sol-gel coatings for polycarbonate

Linda Y. L. Wu et al.

THIN SOLID FILMS (2008)

Article Nanoscience & Nanotechnology

Toughness and adhesion of atomic layer deposited alumina films on polycarbonate substrates

B. A. Latella et al.

SCRIPTA MATERIALIA (2007)