☆ 4.7 Article

Numerical and experimental study of the effects of tangential to axial velocity ratio and structural parameters inside the nozzle on spray characteristics

PHYSICS OF FLUIDS (2023)

Related references

Note: Only part of the references are listed.

Article Mechanics

Spray characteristics of diesel, biodiesel, polyoxymethylene dimethyl ethers blends and prediction of spray tip penetration using artificial neural network

Yu Liu et al.

Summary: This study investigated the spray characteristics of biodiesel and polyoxymethylene dimethyl ethers (PODE) under different injection pressures. It was found that biodiesel blends have a greater spray tip penetration compared to diesel blends, and the addition of PODE brings the spray characteristics of biodiesel closer to pure diesel. An excellent predictive model was also developed using computer technology.

PHYSICS OF FLUIDS (2022)

Add to Collection

Article Thermodynamics

Gas-liquid mass transfer characterization in a thin shrinking film at an atomization nozzle

Axel Canado et al.

Summary: This paper applies a light absorption method to estimate the thickness of atomizing liquid film at microscale and determine the local profile of dioxygen concentration using a dioxygen sensitive dye. The method relies on the Beer-Lambert law and provides a dual measurement of thickness and mass transfer. It is the first successful implementation of this method in thin liquid films in sprays at microscale and with such high velocities.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2022)

Add to Collection

Article Mechanics

Numerical investigation on the role of a mixer on spray impingement and mixing in channel cross-stream airflow

Palaniappan Venkatachalam et al.

Summary: This study numerically investigates the influence of introducing a spin-type mixer and different angular orientations of the mixer blades on the spray-wall interaction and mixing. The results show that the choice of the angular orientation of the mixer governs the extent of droplet deposition and splashing, as well as the spatial uniformity of droplets and ammonia species.

PHYSICS OF FLUIDS (2022)

Add to Collection

Article Mechanics

Computational fluid dynamics characterization of the hollow-cone atomization: Newtonian and non-Newtonian spray comparison

Massimiliano Di Martino et al.

Summary: The study focuses on the characterization of small-scale pressure-swirl spray under laminar flow conditions, and investigates the key parameters that modify the attributes of multiscale flow. Through computational fluid dynamics, the influence of main fluid/packaging parameters on spray properties and the atomization process is analyzed. The entire spray system is modeled by structuring the fragmentation process into multiple stages, linking key features of the hollow-cone spray process to spray pattern and droplet size distribution for both Newtonian and non-Newtonian fluid properties.

PHYSICS OF FLUIDS (2022)

Add to Collection

Article Thermodynamics

Parametric study of heat transfer characteristics of enhanced surfaces in a spray cooling system: An experimental investigation

Azzam S. Salman et al.

Summary: This study conducted experiments to investigate the effects of nozzle-to-surface distance, coolant flow rate, and temperature difference on the heat transfer characteristics of enhanced surfaces in a spray cooling system. The results showed that radial grooves and surface structures played a crucial role in improving heat transfer performance.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Internal and external flow characteristics of multi-nozzle spray with liquid nitrogen

Rong Xue et al.

Summary: The multi-nozzle spray cooling with liquid nitrogen can achieve high heat transfer rate and uniform temperature for a large-scale environmental simulation system. Understanding the flow characteristics is crucial to controlling the mass flow rates and temperature distribution in a cryogenic system. The experimental and numerical approach reveals the flow characteristics of the multi-nozzle spray with liquid nitrogen, providing insights for practical engineering applications.

CRYOGENICS (2021)

Add to Collection

Article Engineering, Chemical

Numerical study of the effect of geometric parameters on the internal flow of a pressure nozzle for dustfall

Junpeng Wang et al.

Summary: Using CFD simulations, this study investigated the effect of main structural parameters on the internal flow of a pressure nozzle, finding that changes in convergent angle, outlet diameter, swirl angle, and flow area significantly impact velocity and swirl degree. Among these parameters, swirl angle and outlet diameter have the most significant influence on the velocity of the nozzle outlet.

ADVANCED POWDER TECHNOLOGY (2021)

Add to Collection

Article Thermodynamics

Effect of spray modes on electrospray cooling heat transfer of ethanol

Haojie Xu et al.

Summary: The heat transfer performance of electrospray cooling has been experimentally investigated with different spray modes, showing that droplet size decreases and spray velocity increases with higher applied voltage. As the spray mode transitions to cone-jet/multi-jet modes, the nucleate boiling region is extended and the critical heat flux increases. Electrospray cooling significantly enhances cooling capacity by precise control under certain conditions.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Engineering, Environmental

Experimental investigation on spray characteristics of twin-fluid nozzle for water mist and its heptane pool fire extinguishing performance

Chan Seok Jeong et al.

Summary: The study indicates that the twin-fluid nozzle outperforms the single-fluid nozzle in fire extinguishing performance, being able to extinguish fires faster and more effectively, while using less water. Additionally, the airflow of the twin-fluid nozzle is identified as a critical factor affecting its fire suppression capabilities.

PROCESS SAFETY AND ENVIRONMENTAL PROTECTION (2021)

Add to Collection

Article Thermodynamics

Comparative study on the enhancement of spray cooling heat transfer using conventional and bio-surfactants

Pengfei Liu et al.

Summary: The study revealed that adding Rhamnolipid can significantly enhance heat transfer during spray cooling, while adding Sophorolipid can lead to a decrease in heat transfer. All three surfactants can enhance heat transfer during nucleate boiling, with biosurfactants performing better than the conventional surfactant.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Mechanics

Air swirl effect on spray characteristics and droplet dispersion in a twin-jet crossflow airblast injector

Shirin Patil et al.

Summary: The paper reports on spray characterization in a novel twin-jet airblast injector, focusing on the effect of injector air swirl on droplet characteristics and dispersion behavior. The addition of air swirl significantly affects spray topology and droplet size downstream of the injector exit, leading to improved atomization quality and high spray dispersion. The results provide insight into the physics behind the improved atomization due to air swirl and demonstrate the injector's ability to achieve atomization quality and high spray dispersion over a wide operating range.

PHYSICS OF FLUIDS (2021)

Add to Collection

Article Mechanics

Three-dimensional computational fluid dynamics simulation of the hollow-cone spray process: The stability of the conical liquid sheet

Massimiliano Di Martino et al.

Summary: This study focuses on the atomization characteristics in small-scale applications and the spray performance in pressure-swirl atomizers. By using computational fluid dynamics, the stability of the gas-liquid interface produced by swirling liquid injection is investigated, and the liquid droplet spray state is examined based on liquid properties and geometric features.

PHYSICS OF FLUIDS (2021)

Add to Collection

Article Mechanics

Study of pressure-swirl atomizer with spiral path at design point and outside of design point

Kiumars Khani Aminjan et al.

Summary: This study focuses on pressure-swirl atomizers with a spiral path, exploring the flow development under different pressure levels. Results show that increasing pressure leads to a larger spray cone angle and smaller droplet diameter. Additionally, increasing the cross-section and length of the spiral path results in thicker fluid film and larger droplet diameter with a reduced spray cone angle.

PHYSICS OF FLUIDS (2021)

Add to Collection

Article Mechanics

Droplet breakup and coalescence of an internal-mixing twin-fluid spray

Hao Wu et al.

Summary: The air-assisted spray consists of a bulk of tiny droplets entrained by high-speed gas-phase flow, with droplets less than 5 micrometers in diameter accounting for the majority. In the far-field of the spray, coalescence dominates droplet collision dynamics.

PHYSICS OF FLUIDS (2021)

Add to Collection

Article Thermodynamics

Surface orientation effects on heat transfer performance of spray cooling

Xiao Zhao et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Mechanics

Spray droplet size distribution and droplet velocity measurements in a firing optical engine

Nikhil Sharma et al.

PHYSICS OF FLUIDS (2020)

Add to Collection

Article Physics, Multidisciplinary

Numerical Investigation on the Thermodynamic Characteristics of a Liquid Film upon Spray Cooling Using an Air-Blast Atomization Nozzle

Jia-Xin Li et al.

ENTROPY (2020)

Add to Collection

Article Thermodynamics

Experimental study on flashing spray characteristics of pressure swirl nozzle with ethanol solution

Jinghe Lu et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2020)

Add to Collection

Article Mechanics

Effect of the physical properties of liquid and ALR on the spray characteristics of a pre-filming airblast nozzle

Mir Muhammad Tareq et al.

INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2020)

Add to Collection

Article Mechanics

Numerical simulation of in-nozzle flow characteristics under flash boiling conditions

Peng Yin et al.

INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2020)

Add to Collection

Article Thermodynamics

Effects of microstructured surface and mixed surfactants on the heat transfer performance of pulsed spray cooling

Ni Liu et al.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2020)

Add to Collection

Article Thermodynamics

Experimental investigation of nozzle geometry effect on two-phase nozzle performance through trilateral flash cycle

Mahdi Ahmadi et al.

THERMAL SCIENCE AND ENGINEERING PROGRESS (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Study on the effects of electrostatic force and spray characteristics in spray cooling of vertical hot strip

Kyung-Hwan Lim et al.

JOURNAL OF ELECTROSTATICS (2020)

Add to Collection

Article Energy & Fuels

Theoretical model of swirling thick film flow inside converging nozzles of various geometries

Boo-Hyoung Bang et al.

FUEL (2020)

Add to Collection

Article Thermodynamics

Experimental study on heat transfer performance of a novel compact spray cooling module

Li-Jia Jiang et al.

APPLIED THERMAL ENGINEERING (2019)

Add to Collection

Article Thermodynamics

On the influence of geometrical parameters on the spray characteristics of high shear injectors

Kuppuraj Rajamanickam et al.

EXPERIMENTAL THERMAL AND FLUID SCIENCE (2019)

Add to Collection

Article Thermodynamics

Measurement of static pressure profiles of vortex flashing R134a flow expanded through convergent-divergent nozzles

Jingwei Zhu et al.

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID (2019)

Add to Collection

Article Nuclear Science & Technology

Experimental study on spray characteristics of pressure-swirl nozzle in China advanced PWR containment

Jiawei Bian et al.

NUCLEAR ENGINEERING AND DESIGN (2019)

Add to Collection

Article Thermodynamics

Study on in-nozzle flow and spray behavior characteristics under various needle positions and length-to-width ratios of nozzle orifice using a transparent acrylic nozzle

Byunggyun Kim et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2019)

Add to Collection

Article Thermodynamics

Enhancement mechanism of high alcohol surfactant on spray cooling: Experimental study

Wei-Wei Zhang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)

Add to Collection

Article Thermodynamics

Characteristics and correlation of nozzle internal flow and jet breakup under flash boiling conditions

Shangze Yang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)

Add to Collection

Article Thermodynamics

Effects of nozzle positioning on single-phase spray cooling

Xuan Gao et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2017)

Add to Collection

Article Thermodynamics

Experimental study on the relation between internal flow and flashing spray characteristics of R134a using straight tube nozzles

Xin-Sheng Wang et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2017)

Add to Collection

Article Thermodynamics

Spray characteristics of pressure-swirl nozzles at different nozzle diameters

Tao Zhang et al.

APPLIED THERMAL ENGINEERING (2017)

Add to Collection

Article Thermodynamics

Near-field mixing of jets issuing from an array of round nozzles

Shahriar Ghahremanian et al.

INTERNATIONAL JOURNAL OF HEAT AND FLUID FLOW (2014)

Add to Collection

Article Thermodynamics

Thermal effects on a pressure swirl nozzle in spray cooling

J. L. Xie et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2014)

Add to Collection

Article Mechanics

Viscous flow through the swirl chamber of a pressure-swirl atomizer

E. Wimmer et al.

INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2013)

Add to Collection

Article Engineering, Multidisciplinary

Comparison of turbulence models in simulating swirling pipe flows

Andrew Escue et al.

APPLIED MATHEMATICAL MODELLING (2010)

Add to Collection

Article Thermodynamics

Nozzle geometry effects in liquid jet array impingement

Brian P. Whelan et al.

APPLIED THERMAL ENGINEERING (2009)

Add to Collection

Article Thermodynamics

Flow characteristics and heat transfer performances of a semiconfined impinging array of jets: effect of nozzle geometry

BPE Dano et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2005)

Add to Collection

© Peeref 2019-2024. All rights reserved.