☆ 4.6 Article

Improvement in Corrosion Resistance and Interfacial Contact Resistance Properties of 316L Stainless Steel by Coating with Cr, Ti Co-Doped Amorphous Carbon Films in the Environment of the PEMFCs

MOLECULES (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Chemical

Investigation of graphite conductive adhesive coated on SS316L used for bipolar plates of proton-exchange membrane fuel cell

Reza Taherian et al.

Summary: In this study, a polymer-based carbon adhesive was used as a conductive coating on SS316L bipolar plates, with the addition of graphite to improve electrical conductivity and structural stability. It was found that PVAc/60 wt.% G is a suitable coating for SS316L bipolar plates.

JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Analytical

Detection and Analysis of Corrosion and Contact Resistance Faults of TiN and CrN Coatings on 410 Stainless Steel as Bipolar Plates in PEM Fuel Cells

Mohsen Forouzanmehr et al.

Summary: Bipolar plates are crucial components in PEM fuel cell systems. In this study, researchers coated 410 stainless steel with titanium nitride and chromium nitride, and compared the corrosion resistance and interfacial contact resistance to select the best coating. The results showed that chromium nitride is the most suitable choice for the 410 stainless steel coating.

SENSORS (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Vertical-Graphene-Reinforced Titanium Alloy Bipolar Plates in Fuel Cells

Feng Yu et al.

Summary: This study proposes a method for surface reinforcement of titanium alloy bipolar plates using a vertical graphene coating, which effectively reduces the corrosion rate and interfacial contact resistance (ICR) in PEMFC operating environments, while improving thermal conductivity and water contact angle. The research provides a new opportunity for reinforcing metallic surfaces in high-performance electrodes used in energy and catalyst applications.

ADVANCED MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion resistance and conductivity of NbN-coated 316L stainless steel for membrane fuel cells

Mohan Chen et al.

Summary: In this study, NbN coatings were deposited using multi-arc ion plating at different nitrogen partial pressures, and the effects of phase composition, microstructure, and surface morphology on the anti-corrosion behavior and conductivity were investigated. The results showed that the coating deposited at a relatively high nitrogen partial pressure exhibited the best corrosion resistance and conductivity.

CORROSION SCIENCE (2022)

Add to Collection

Article Chemistry, Physical

Investigation of corrosion properties with Ni-P/TiNO coating on aluminum alloy bipolar plates in proton exchange membrane fuel cell

Jinzhou Zhang et al.

Summary: Aluminum alloy bipolar plates have potential applications in PEMFC due to their lightweight and low cost. However, their susceptibility to corrosion limits their usage. A Ni-P/TiNO coating prepared using electroless plating and CFUMSIP technology improves the corrosion resistance and stability of the aluminum alloy bipolar plates.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion and conductivity behavior of titanium-doped amorphous carbon film coated SS316L in the environment of PEMFCs

Wei Li et al.

Summary: The introduction of Ti atoms in α-C film can significantly improve its electrical properties, corrosion resistance, stability under nobler potentials, and durability in service environments.

MATERIALS CHEMISTRY AND PHYSICS (2022)

Add to Collection

Article Chemistry, Physical

Corrosion-resistant and interfacial conductive AlTiVCrMo high-entropy alloy and (AlTiVCrMo)Nx high-entropy ceramics coatings for surface modification of bipolar plates in proton exchange membrane fuel cells

Weiqing Yan et al.

Summary: Metal bipolar plates (BPPs) have the potential to replace conventional carbon-based BPPs, but the issues of corrosion and passivation need to be addressed. Corrosion-resistant and interfacial conductive high-entropy alloy and ceramic coatings have shown promise as surface modification methods for bipolar plates, improving their corrosion resistance and conductivity.

JOURNAL OF POWER SOURCES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Electrochemical Behavior and Surface Conductivity of C/TiC Nanocomposite Coating on Titanium for PEMFC Bipolar Plate

Wei Meng et al.

Summary: A C/TiC nanocomposite coating was successfully prepared on a titanium surface and characterized, showing excellent corrosion resistance and low interfacial contact resistance.

METALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Nano-Cr2N dominated films with high conductivity and strong corrosion resistance for Ti bipolar plates

Li Chen et al.

Summary: In this study, CrN films with high conductivity and strong corrosion resistance were successfully deposited on Ti plates by high power impulse magnetron sputtering. The method effectively inhibited the formation of columnar structure and formed a nanostructure encapsulated amorphous Cr2N clusters, providing good protection for the Ti plates.

MATERIALS & DESIGN (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Improvement in corrosion resistance of 316L stainless steel in simulated body fluid mixed with antiplatelet drugs by coating with Ti-doped DLC films for application in biomaterials

Pornwasa Wongpanya et al.

Summary: The structures and corrosion behavior of titanium-doped DLC films on 316L SS were investigated. It was found that titanium doping improved the corrosion resistance of DLC films, and the inhibition efficiency was further enhanced when antiplatelet drugs were present in the simulated body fluid.

CORROSION SCIENCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of hydrophobic and anti-corrosive behavior of Cr-DLC film on stainless steel bipolar plate

Limin Wang et al.

Summary: In this study, Cr-DLC films without a transition layer were fabricated on stainless steel BPP to improve its corrosion resistance and hydrophobic electrical resistivity. The results showed that the sample with a Cr content of 2.58 at.% exhibited better contact angle and corrosion resistance, attributed to its lower surface roughness, the presence of a surface passivation layer, and the inertness of CrxCy.

DIAMOND AND RELATED MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

High corrosion resistance of reduced graphene oxide coated 316L stainless steel bipolar plate for proton exchange membrane fuel cell prepared by a facile method

Qi Yin et al.

Summary: The study demonstrates that utilizing GO adsorbing-H2 reducing method improves the corrosion resistance of 316L stainless steel bipolar plates in PEMFC, with the rGO coating showing significantly higher corrosion resistance compared to bare 316L stainless steel.

MATERIALS CHEMISTRY AND PHYSICS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Characterization and properties of NbN-Nb bilayer formed on titanium for bipolar plates

Hongyu Shen et al.

Summary: In this study, a NbN/Nb bilayer structure was prepared on titanium to be used as bipolar plates for PEMFCs. The corrosion resistance and electrical conductivity of the samples were measured in simulated PEMFCs environments. The findings show that the duplex-treated sample exhibits significantly lower corrosion current density and interfacial contact resistance compared to untreated titanium.

MATERIALS CHEMISTRY AND PHYSICS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion resistance and contact resistance properties of Cr-doped amorphous carbon films deposited under different carbon target current on the 316L stainless steel bipolar plate for PEMFC

Baosen Mi et al.

Summary: Cr-doped amorphous carbon coatings were deposited on 316L stainless steel using magnetron sputtering technology. By adjusting the current value of the carbon target, coatings with different phase structures were obtained. The results showed that samples with carbon target currents of 3A and 5A exhibited better corrosion resistance.

VACUUM (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Electronic conductive and corrosion mechanisms of dual nanostructure CuCr-doped hydrogenated carbon films for SS316L bipolar plates

Q. Jia et al.

Summary: A new method for preparing carbon-coated metal bipolar plates is proposed in this study, using reactive magnetron sputtering with a Cr0.6Cu0.4 target in methane and argon atmosphere. The resulting C18.6Cr0.06Cu (S65) film has a high deposition rate and good conductivity. The unique structure of the film provides excellent electrical and anti-corrosion properties.

MATERIALS TODAY CHEMISTRY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of high potential corrosion protection with titanium carbonitride coating on 316L stainless steel bipolar plates

Jie Jin et al.

Summary: Depositing TiN and TiCN coatings on stainless steel substrates using Closed Field Unbalanced Magnetron Sputter Ion Plating can improve the durability and corrosion resistance of stainless steel bipolar plates in proton exchange membrane fuel cells at high potential, meeting the Department of Energy targets for interfacial contact resistance.

CORROSION SCIENCE (2021)

Add to Collection

Article Electrochemistry

Low-cost graphite coated copper as bipolar plates of proton exchange membrane fuel cells for corrosion protection

Sida Wu et al.

Summary: This study explores a new method for preparing a graphite coating on the surface of copper foil, which enhances corrosion resistance in a fuel cell environment and maintains the anode in a cathodic protection state. Additionally, the interfacial contact resistance of copper with graphite coating meets DOE targets.

FUEL CELLS (2021)

Add to Collection

Article Chemistry, Physical

Synthesis and Ex-Situ characterizations of diamond-like carbon coatings for metallic bipolar plates in PEM fuel cells

Ibrahim Alaefour et al.

Summary: This study investigates diamond-like carbon (DLC) film coatings as corrosion protection coatings for metallic-based bipolar plates. It is found that higher deposition power and absence of argon gas result in more sp3 bonds and higher electrical resistivity. Coatings deposited from methane exhibit superior adhesion to stainless steel substrates, and coatings with low power and high argon gas percentage provide better anti-corrosion protection.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

Add to Collection

Article Chemistry, Physical

Evaluation of vacuum heat-treated α-C films for surface protection of metal bipolar plates used in polymer electrolyte membrane fuel cells

Wei Li et al.

Summary: Metal bipolar plates used in proton exchange membrane fuel cells have serious corrosion issues, but amorphous carbon films with titanium interlayer show improved corrosion resistance and conductivity after vacuum heat treatment, making them a potential solution for improving performance in harsh environments.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

Add to Collection

Review Green & Sustainable Science & Technology

An overview of bipolar plates in proton exchange membrane fuel cells

Aubrey Tang et al.

Summary: Bipolar plates play a crucial role in proton exchange membrane fuel cells, but their weight, volume, and cost present challenges to commercialization. This paper reviews materials and manufacturing processes for bipolar plates, highlighting additive manufacturing as an innovative method to improve their properties.

JOURNAL OF RENEWABLE AND SUSTAINABLE ENERGY (2021)

Add to Collection

Article Chemistry, Physical

The effect of Cr doped in amorphous carbon films on electrical conductivity: Characterization and mechanism

Kun Hou et al.

Summary: Chromium-doped amorphous carbon films can enhance the conductivity and corrosion resistance of metallic bipolar plates, forming chromium carbide phase and pure metal phase. Additionally, chromium doping affects nano-hardness and surface roughness.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Improvement of corrosion resistance and biocompatibility of 316L stainless steel for joint replacement application by Ti-doped and Ti-interlayered DLC films

Pornwasa Wongpanya et al.

Summary: Titanium was incorporated into diamond-like carbon (DLC) films deposited on 316L stainless steel using filtered cathodic vacuum arc, leading to the formation of different structures. Among these, ta-C:Ti/Ti exhibited the best corrosion resistance and biocompatibility, making it a promising DLC film for joint replacement biomaterials.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Ceramics

A reactive-sputter-deposited TiSiN nanocomposite coating for the protection of metallic bipolar plates in proton exchange membrane fuel cells

Shuang Peng et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Properties of a Plasma-Nitrided Coating and a CrNx Coating on the Stainless Steel Bipolar Plate of PEMFC

Meiling Xu et al.

COATINGS (2020)

Add to Collection

Article Materials Science, Coatings & Films

Microstructure and mechanical, electrical, and electrochemical properties of sputter-deposited multicomponent (TiNbZrTa)Nx coatings

Rui Shu et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Article Chemistry, Physical

Ultrathin effective TiN protective films prepared by plasma-enhanced atomic layer deposition for high performance metallic bipolar plates of polymer electrolyte membrane fuel cells

Woo-Jae Lee et al.

APPLIED SURFACE SCIENCE (2020)

Add to Collection

Article Chemistry, Physical

Majorization of GLC properties by the introduction of silver nanowires as conductive framework for metal bipolar plates

Fangyuan Yan et al.

APPLIED SURFACE SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Growth of nanocrystalline β-Nb2N coating on 430 ferritic stainless steel bipolar plates of PEMFCs by disproportionation reaction of Nb(IV) ions in molten salt

Ling Xu Yang et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Materials Science, Coatings & Films

Microstructure and property evolution of diamond-like carbon films co-doped by Al and Ti with different ratios

Yong Zhou et al.

SURFACE & COATINGS TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Physical

Amorphous carbon films doped with silver and chromium to achieve ultra-low interfacial electrical resistance and long-term durability in the application of proton exchange membrane fuel cells

Di Zhang et al.

CARBON (2019)

Add to Collection

Article Chemistry, Physical

Evaluation of Ni-Cr-P coatings electrodeposited on low carbon steel bipolar plates for polymer electrolyte membrane fuel cell

Uttam K. Chanda et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2018)

Add to Collection

Article Chemistry, Physical

Surface diffusion modification AISI 304SS stainless steel as bipolar plate material for proton exchange membrane fuel cell

Jianli Wang et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2012)

Add to Collection

Article Chemistry, Physical

Deposition and properties of Al-containing diamond-like carbon films by a hybrid ion beam sources

Wei Dai et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

Add to Collection

Article Physics, Applied

Nanocomposite nc-TiC/a-C thin films for electrical contact applications

Erik Lewin et al.

JOURNAL OF APPLIED PHYSICS (2006)

Add to Collection

Article Chemistry, Physical

Ferritic stainless steels as bipolar plate material for polymer electrolyte membrane fuel cells

HL Wang et al.

JOURNAL OF POWER SOURCES (2004)

Add to Collection

Article Materials Science, Coatings & Films

Deposition and characterization of Ti- and W-containing diamond-like carbon films by plasma source ion implantation

K Baba et al.

SURFACE & COATINGS TECHNOLOGY (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Determination of bonding in diamond-like carbon by Raman spectroscopy

AC Ferrari

DIAMOND AND RELATED MATERIALS (2002)

Add to Collection

Article Engineering, Biomedical

Titanium containing amorphous hydrogenated carbon films (a-C : H/Ti): surface analysis and evaluation of cellular reactions using bone marrow cell cultures in vitro

A Schroeder et al.

BIOMATERIALS (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.