Related references
Note: Only part of the references are listed.Study on High-Temperature Mechanical Properties of Fe-Mn-C-Al TWIP/TRIP Steel
Guangkai Yang et al.
METALS (2021)
Heat Treatment Design for a QP Steel: Effect of Partitioning Temperature
Marcel Carpio et al.
METALS (2021)
Micromechanical Behavior of Transformation-Induced Plasticity-Assisted Annealed Martensitic Steel Using In Situ Neutron Diffraction
Chenghao Song et al.
STEEL RESEARCH INTERNATIONAL (2020)
Improvement of AISI 4340 steel properties by intermediate quenching – microstructure, mechanical properties, and fractography
Afshin Mehrabi et al.
International Journal of Materials Research (2020)
Perspectives on Quenching and Tempering 4340 Steel
A. J. Clarke et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Structure-Property Correlation of Quenching and Partitioning Heat Treated Silicon-Manganese Steel
Palaksha Pilar Acharya et al.
SILICON (2019)
Microstructure and properties of thermomechanically treated and bake hardened AISI 4340 steel
Arun Kumar et al.
MATERIALS TODAY-PROCEEDINGS (2019)
Effect of Q&P Heat Treatment on Fine Microstructure and Mechanical Properties of a Low-alloy Medium-carbon Steel
Rahim Jafari et al.
6TH INTERNATIONAL BIENNIAL CONFERENCE ON ULTRAFINE GRAINED AND NANOSTRUCTURED MATERIALS (UFGNSM 2017) (2018)
Tempering of Lath Martensite in Low and Medium Carbon Steels: Assessment and Challenges
George Krauss
STEEL RESEARCH INTERNATIONAL (2017)
An ultrahigh strength steel with ultrafine-grained microstructure produced through intercritical deformation and partitioning process
Heping Liu et al.
MATERIALS & DESIGN (2015)
Influence of alloying elements on the microstructure evolution and mechanical properties in quenched and partitioned steels
N. Maheswari et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Quenching and Partitioning Steel Heat Treatment
Li Wang et al.
METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS (2013)
EBSD study of a hot deformed austenitic stainless steel
H. Mirzadeh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Formability of Al-Nb Bearing Ultra High-strength TRIP-aided Sheet Steels with Bainitic Ferrite and/or Martensite Matrix
Koh-ichi Sugimoto et al.
ISIJ INTERNATIONAL (2010)
Characterization of microstructure obtained by quenching and partitioning process in low alloy martensitic steel
C. Y. Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Comparison of mechanical properties of martensite/ferrite and bainite/ferrite dual phase 4340 steels
N. Saeidi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Process simulation and microstructure analysis of low carbon Si-Mn quenched and partitioned steel
Zhao Cai et al.
JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL (2008)
Isothermal transformation of austenite to bainite in high carbon steels
S. A. Sajjadi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
Ultrafine grained ferrite-marten site dual phase steels fabricated via equal channel angular pressing: Microstructure and tensile properties
YI Son et al.
ACTA MATERIALIA (2005)
Share Paper
