Related references
Note: Only part of the references are listed.Investigation of the Peritectic Phase Transition in a Commercial Peritectic Steel Under Different Cooling Rates Using In Situ Observation
Tao Liu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2020)
δ-Ferrite Formation and Its Effect on the Mechanical Properties of Heavy-Section AISI 316 Stainless Steel Casting
Qiyu Wang et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Effect of the Process Gas and Scan Speed on the Properties and Productivity of Thin 316L Structures Produced by Laser-Powder Bed Fusion
C. Pauzon et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Densification Behavior and Influence of Building Direction on High Anisotropy in Selective Laser Melting of High-Strength 18Ni-Co-Mo-Ti Maraging Steel
Yuchao Bai et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Review of Peritectic Solidification Mechanisms and Effects in Steel Casting
Ghavam Azizi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2020)
Predominant Solidification Modes of 316 Austenitic Stainless Steel Coatings Deposited by Laser Cladding on 304 Stainless Steel Substrates
L. H. R. Apolinario et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)
Equivalent heat source approach in a 3D transient heat transfer simulation of full-penetration high power laser beam welding of thick metal plates
Antoni Artinov et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2018)
High performance computation of residual stress and distortion in laser welded 301L stainless sheets
Hui Huang et al.
FINITE ELEMENTS IN ANALYSIS AND DESIGN (2017)
Comparison of residual stress induced by TIG and LBW in girth weld of AISI 304 stainless steel pipes
Jijin Xu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Solidification mechanism of austenitic stainless steels solidified with primary ferrite
Hiroshige Inoue et al.
ACTA MATERIALIA (2017)
Effects of processing parameters on tensile properties of selective laser melted 304 stainless steel
Kai Guan et al.
MATERIALS & DESIGN (2013)
Cracking behavior and mechanical properties of austenitic stainless steel parts produced by laser metal deposition
J. Yu et al.
MATERIALS & DESIGN (2013)
Identification of Defect Prone Peritectic Steel Grades by Analyzing High-Temperature Phase Transformations
Peter Presoly et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Numerical simulation of residual stresses induced by laser beam welding in a SUS316 stainless steel pipe with considering initial residual stress influences
Dean Deng et al.
NUCLEAR ENGINEERING AND DESIGN (2010)
Study on microstructure and mechanical properties of 304 stainless steel joints by TIG, laser and laser-TIG hybrid welding
Jun Yan et al.
OPTICS AND LASERS IN ENGINEERING (2010)
Prediction of laser beam welding-induced distortions and residual stresses by numerical simulation for aeronautic application
Muhammad Zain-ul-Abdein et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
The dependence of crack properties on the Cr/Ni equivalent ratio in AISI 304L austenitic stainless steel weld metals
D. J. Lee et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Small-scale resistance spot welding of austenitic stainless steels
Shinji Fukumoto et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Kinetics of the peritectic reaction in an Fe-C alloy
Dominic Phelan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels
J. Talonen et al.
ACTA MATERIALIA (2007)
Thermo-mechanical modeling of laser welding of AA5083 sheets
R. Spina et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2007)
In-situ observed dynamics of peritectic solidification and δ/γ transformation of Fe-3 to 5 At. Pct Ni alloys
Y Arai et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2005)
Effect of microfissures on mechanical properties of 308L austenitic stainless steel weld metals
Y Cui et al.
JOURNAL OF MATERIALS SCIENCE (2005)
Effect of strain rate on the strain-induced γ→α′-martensite transformation and mechanical properties of austenitic stainless steels
J Talonen et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2005)
High temperature behavior of Ni-base weld metal - Part II - Insight into the mechanism for ductility dip cracking
AJ Ramirez et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Peritectic reaction and solidification in iron-nickel alloys
NJ McDonald et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2003)
Effect of nitrogen addition on microstructure and fusion zone cracking in type 316L stainless steel weld metals
V Shankar et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Phase formation during solidification of AISI 304 austenitic stainless steel
A Hunter et al.
SCRIPTA MATERIALIA (2002)
Relation between microstructure, composition, and hot cracking in Ti-stabilized austenitic stainless steel weldments
V Shankar et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2000)
Share Paper
