☆ 4.7 Article

Investigation on the microstructure, mechanical and electrical properties of Ti3SiC2/Cu joint obtained by Ti25Zr25Ni25Cu25 amorphous high entropy alloy and Ag composite filler

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Designing a low-melting Sn6Ag7Ni4Co2Ti high entropy alloy filler to optimize microstructure and mechanical properties of Ti3SiC2/Cu joint

Xin Nai et al.

Summary: The study found that using Sn6Ag7Ni4Co2Ti low-melting high entropy alloy as filler can achieve a defect-free Ti3SiC2/Cu brazed joint. The high-entropy effect and hysteresis effect of the alloy effectively reduce the rate of atomic diffusion and slow down the metallurgical reaction, which is beneficial to maintain a simple interface structure. The joint brazed with Sn6Ag7Ni4Co2Ti HEA filler achieved a maximum shear strength of 60.55 +/- 3.45 MPa, which is 34.85% higher than the joint brazed with Ag-26.7Cu-4.5Ti filler.

MATERIALS CHARACTERIZATION (2023)

Add to Collection

Article Engineering, Manufacturing

Effect of Ti content on microstructure and mechanical properties of SiCf/SiC composites/GH536 superalloy joints brazed with CoFeCrNiCuTi high entropy filler

Shuai Zhao et al.

Summary: In this study, SiCf/SiC composite and GH536 superalloy were vacuum brazed using a self-made CoFeNiCrCuTix high entropy filler with varying Ti content. The influence of Ti content in the filler on the microstructure and mechanical properties of the joints was investigated. Increasing the Ti content in the filler shifted the interfacial reaction control from Fe and Ni elements to Ti elements. The presence of TiC phase in continuous strips helped inhibit and reduce the formation of brittle Fe-Si and Ni-Si phases, resulting in improved mechanical properties. The maximum shear strength of the brazed joint reached 98.23 MPa when the molar ratio of Ti content to other elements in the filler was 1, which was 14.10% higher compared to filler without Ti element. This study demonstrates that Ti element in high entropy fillers can regulate interfacial reactions and reduce the amount of brittle intermetallic compounds, presenting a new idea for high entropy filler design and its application in brazing.

JOURNAL OF MANUFACTURING PROCESSES (2023)

Add to Collection

Article Materials Science, Ceramics

Microstructural evolution and growth kinetics of interfacial reaction layers in SUS430/Ti3SiC2 diffusion bonded joints using a Ni interlayer

Qiang Cheng et al.

Summary: Ti3SiC2 ceramic and SUS430 stainless steel were successfully joined using Ni interlayers and solid diffusion bonding technique. It was found that the Ni foil effectively prevented inter-diffusion and reaction between Ti3SiC2 and SS, and the good transition in the joint contributed to the sound joining. The interface in the joints adjacent to SS matrix was composed of gamma solid solution and a small amount of sigma intermetallic compound.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Improvement for Ti3SiC2/Cu joint brazed using composite fillers with abnormal expansion ceramic particulates

Haiyan Chen et al.

Summary: Using composite filler with YSZ solid-state phase transformation ceramic particulates, this study successfully reduced the residual stresses and improved the mechanical strength of ceramic/metal brazing joints. The microstructure of joints and YSZ particulates in the interface were investigated, and the effect of YSZ particulates content on the mechanical properties of joints was evaluated. The results showed that the solid-state phase transformation of YSZ particulates played a crucial role in reducing the residual stress and enhancing the shear strength of the joints.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Chemistry, Physical

The effect of annealing temperatures on the phase constitutes, thermal properties and corrosion behaviors of Ti-Ni-Zr-Cu high entropy alloy thin ribbons

Xiaoyang Yi et al.

Summary: In this study, amorphous Ti-Ni-Zr-Cu thin ribbons were successfully prepared using rapid spinning technology. The researchers investigated the crystallization temperature, activation energy of crystallization, and phase constituents of the annealed thin ribbons. The results showed that the annealing temperature had a significant effect on the phase constituents, lattice constant, and Vickers hardness of the Ti-Ni-Zr-Cu thin ribbons.

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of SiCf/SiC composites/GH536 superalloy joints brazed with CoFeNiCrCu high-entropy alloy filler

Shuai Zhao et al.

Summary: In this study, SiCf/SiC and GH536 were brazed using a high entropy alloy CoFeNiCrCu filler. The interfacial microstructure, brazing mechanism, and mechanical properties of the joint were investigated. Due to the high entropy mixing effect of the filler, a random solid solution formed in the seam, resulting in greatly enhanced mechanical properties of the joint.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Understanding the microstructure evolution mechanism and the microstructure-strength correlations of Ti3SiC2/Ti2AlNb joint brazed with AgCu interlayer

Bo Zhang et al.

Summary: The effect of brazing parameters on the microstructure of a Ti3SiC2 ceramic brazed joint with a Ti2AlNb alloy was investigated and the microstructure evolution mechanism of the joint was clarified through characterization of the interfacial reaction products. The unique crystal structure of Ti3SiC2 phase leads to the effortless de-intercalation of Si atoms and subsequent complex interfacial reactions. The brazing temperature has a significant influence on these reactions, with a maximum shear strength achieved at 860°C for 20 minutes.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Interfacial strengthening mechanism of C/C/Nb0.74CoCrFeNi2/Nb brazed joints: Stress-relieving effects of the FCC phase

Jixu Hu et al.

Summary: This study successfully joined a carbon-fiber-reinforced carbon-matrix (C/C) composite and Nb using a Nb0.74CoCrFeNi2 eutectic high-entropy alloy filler. The research found that adjusting the content of the face-centered cubic (FCC) phase can enhance the strength of the joint. The results of the study are of great significance for improving the joining of dissimilar materials.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Ceramics

Brazing ZrB2-SiC ceramics to Nb with a novel CoFeNiCrCu high entropy alloy

Gang Wang et al.

Summary: In this study, ZrB2-SiC ceramic and Nb were brazed using a novel high entropy alloy CoFeNiCrCu filler. The newly generated Cr2B improved interfacial bonding strength and a composite microstructure containing a soft FCC and hard Laves phase significantly enhanced joint strength. Furthermore, influences of brazing temperature on interfacial reaction and shear strength of joint were investigated, with successful results at 1160 degrees C for 60 minutes.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Crystallography

Improvement for Interfacial Microstructure and Mechanical Properties of Ti3SiC2/Cu Joint Brazed by Ag-Cu-Ti Filler with Copper Mesh

Haiyan Chen et al.

Summary: Ti3SiC2 ceramic and copper were vacuum brazed successfully using Ag-Cu-Ti filler and Ag-Cu-Ti filler with copper mesh. The addition of copper mesh and optimization of brazing parameters improved the mechanical properties of the joints, resulting in a higher shear strength.

CRYSTALS (2021)

Add to Collection

Article Materials Science, Ceramics

Influence of Ti3SiC2 content on erosion behavior of Cu-Ti3SiC2 cathode under vacuum arc

Sieglind Ngai et al.

Summary: The study showed that an increase in Ti3SiC2 content in Cu-Ti3SiC2 composites results in decreased relative density and bending strength, while hardness and electrical resistivity increase. The morphology and phase composition of the erosion zone are primarily influenced by the decomposition process and the amount of Ti3SiC2 in the cathode.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

A novel joining of Cf/C composites using AlCoCrFeNi2.1 high-entropy brazing filler alloys

Haitao Xu et al.

Summary: In this study, a novel brazing of C-f/C composites using AlCoCrFeNi2.1 high-entropy alloys as the interlayer was successfully achieved. The joints were found to have a typical structure of C-f/C zone, continuous metallic layer, and filling phases. Increasing the brazing temperature led to higher average shear strength and the formation of a hybrid structure in the joints.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Controlling interfacial reactions of Ti3SiC2/Ti2AlNb brazed joints by transferring graphene layers

Zhan Sun et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Thermal expansion of Cu/carbon nanotube composite wires and the effect of Cu-spatial distribution

Rajyashree Sundaram et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Chemistry, Physical

Wetting kinetics and spreading phenomena of the precursor film and bulk liquid in the AgCuTi/TC4 system

Guanpeng Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Chemistry, Physical

Co effects on Cu-Ni-Si alloys microstructure and physical properties

Zhuan Zhao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Engineering, Manufacturing

Effect of brazing temperature on microstructure and mechanical properties of TiAl/ZrB2 joint brazed with CuTiZrNi filler

Gang Wang et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

Add to Collection

Article Chemistry, Physical

Electronic transport in equiatomic CuZrNiTi alloy

S. Uporov et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Materials Science, Ceramics

Contact-reactive brazing of Ti3SiC2 ceramic to TC4 alloy using a Ni interlayer: Interfacial microstructure and joining properties

Y. H. Xia et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of the SiC/Zr4 joints brazed with TiZrNiCu filler for nuclear application

Qin Qi et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of the SiC/Zr4 joints brazed with TiZrNiCu filler for nuclear application

Qin Qi et al.

PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

Interfacial microstructure and mechanical properties of TC4/Ti3SiC2 contact-reactive brazed joints using a Cu interlayer

Y. Wang et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

Ti3SiC2/UO2 composite pellets with superior high-temperature thermal conductivity

Bingqing Li et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of surface microstructure on the active element content and wetting behavior of brazing filler metal during brazing Ti3SiC2 ceramic and Cu

H. Y. Chen et al.

VACUUM (2018)

Add to Collection

Review Materials Science, Multidisciplinary

High-Entropy Alloys: Potential Candidates for High-Temperature Applications - An Overview

Sathiyamoorthi Praveen et al.

ADVANCED ENGINEERING MATERIALS (2018)

Add to Collection

Review Chemistry, Physical

Mechanical and corrosion properties of Ti-Ni-Cu-Zr metallic glass matrix composites

Q. Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Interfacial Behavior and Its Effect on Mechanical Properties of Cf/SiC Composite/TiAl6V4 Joint Brazed with TiZrCuNi

Dongyu Fan et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)

Add to Collection

Article Engineering, Industrial

Microstructural evolution mechanisms of Ti600 and Ni-25%Si joint brazed with Ti-Zr-Ni-Cu amorphous filler foil

Xiaopeng Li et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)

Add to Collection

Review Materials Science, Multidisciplinary

A critical review of high entropy alloys and related concepts

D. B. Miracle et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Ceramics

Joining of Cf/SiC composite to Ti-6Al-4V with (Ti-Zr-Cu-Ni) plus Ti filler based on in-situ alloying concept

Dongyu Fan et al.

CERAMICS INTERNATIONAL (2017)

Add to Collection

Article Materials Science, Ceramics

Joining Ti3SiC2 MAX phase with 308 stainless steel and aluminum fillers by tungsten inert gas (TIG)-brazing process

Y. Hadji et al.

CERAMICS INTERNATIONAL (2016)

Add to Collection

Article Chemistry, Physical

Suppressing spinodal decomposition by adding Co into Cu-Ni-Si alloy

XiangPeng Xiao et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Interfacial study of NiTi-Ti3SiC2 solid state diffusion bonded joints

A. Kothalkar et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Chemistry, Physical

Effect of cooling rate on the phase transformation behavior and mechanical properties of Ni-rich NiTi shape memory alloy

Y. Motemani et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2009)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of coefficient of thermal expansion of silver thin film on different substrates using X-ray diffraction

Yeongseok Zoo et al.

THIN SOLID FILMS (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes

JW Yeh et al.

ADVANCED ENGINEERING MATERIALS (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.