☆ 4.7 Article

Microstructure-Toughness relationships in 316L stainless steel produced by laser powder bed fusion

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2023)

Related references

Note: Only part of the references are listed.

Article Mechanics

Plastically heterogeneity-driven fracture in additive manufactured steels

Weipeng Li et al.

Summary: Tuning the microstructures in additive manufactured (AM) 316L stainless steels can enhance the toughness of metals by resisting crack propagation. A plastically heterogeneity-driven fracture manner resulting from the unique microstructures in AM steels provides a superior combination of strength and toughness compared to conventional steels. The natural heterogeneous microstructural arrangement of coarse-grain (CG) and fine-grain (FG) zones in the AM steel allows for strong strain/stress partitioning and regional hardening processes, preventing crack propagation. Additionally, low-angle grain boundaries (LAGBs) and dislocation cells at the microscale uniformly strengthen the matrix without introducing stress concentration and detrimental damage incidents.

ENGINEERING FRACTURE MECHANICS (2023)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of heat treatment on creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

Meimei Li et al.

Summary: The objective of this study is to understand the thermal stability of microstructure and its effect on the creep behavior of additively-manufactured 316L stainless steel (AM 316L SS). The study found that different heat treatments at various temperatures had an impact on the material's cell structure, elemental segregation, and oxide particles, which in turn affected the creep life and creep rate.

JOURNAL OF NUCLEAR MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Multi-scale characterisation of microstructure and texture of 316L stainless steel manufactured by laser powder bed fusion

Maxwell Moyle et al.

Summary: The study analyzed the microstructure of 316L stainless steel builds produced by additive manufacturing using advanced microscopy techniques. Results showed that changes in processing parameters led to variations in grain structures, texture, and hardness, with additional insights provided into how grains in AM 316L steel accommodate strain.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Nanoscience & Nanotechnology

On the thermal coarsening and transformation of nanoscale oxide inclusions in 316L stainless steel manufactured by laser powder bed fusion and its influence on impact toughness

Pu Deng et al.

Summary: This study explores the thermal evolution of nanoscale oxide inclusions in 316L stainless steel and reveals the key driving forces and mechanisms behind oxide coarsening during recrystallization. The interaction between grain boundaries and oxides results in the accumulation of oxides at grain boundaries, which promotes microvoid formation and intergranular fracture in the material after recrystallization.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanisms controlling fracture toughness of additively manufactured stainless steel 316L

Deepak Kumar et al.

Summary: This study compared the fracture toughness of two different additive manufacturing processes, selective laser melting (SLM) and wire arc additive manufacturing (WAAM), for stainless steel 316L. It found that the SLM manufactured samples exhibited higher fracture toughness, likely due to their higher twin density and propensity for dislocation slip.

INTERNATIONAL JOURNAL OF FRACTURE (2022)

Add to Collection

Article Engineering, Mechanical

Deformation faulting and dislocation-cell refinement in a selective laser melted 316L stainless steel

Feng He et al.

Summary: The selective laser melted (SLM) 316L stainless steel (316L SS) has superior tensile ductility and doubled yield strength compared to its wrought counterpart. The improved yield strength is attributed to unique cellular substructures featured by Cr/Mo-segregation and trapped dislocations. The excellent ductility is mainly understood from deformation twinning and two newly discovered deformation mechanisms, deformation faulting and dislocation cell refinement, which dominate the whole tensile deformation significantly.

INTERNATIONAL JOURNAL OF PLASTICITY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Dependency of recrystallization kinetics on the solidification microstructure of 316L stainless steel processed by laser powder bed fusion (LPBF)

Edouard de Sonis et al.

Summary: This study compared the recrystallization kinetics of two 316L stainless steels produced by Laser Powder-Bed Fusion (LPBF), and found that the differences in microstructure have a significant impact on recrystallization kinetics. It was observed that a high density of low-angle boundaries (LAB) can promote recrystallization by increasing energy near the grain boundaries, leading to the formation of recrystallization nuclei. The design of microstructures with low LAB could result in higher stability at high temperatures.

MATERIALS CHARACTERIZATION (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of solidification conditions on chemical heterogeneities and dislocations patterning in additively manufactured 316L stainless steel

Sylvain Depinoy

Summary: The dendritic substructure of 316L stainless steel processed by Laser Powder Bed Fusion (L-PBF) was experimentally investigated. It was found that there were no crystalline misorientations between neighboring dendrites, indicating that interdendritic dislocations were not geometrically necessary dislocations stemming from solidification but rather arose from thermomechanical straining during post-solidification cooling.

MATERIALIA (2022)

Add to Collection

Article Materials Science, Multidisciplinary

A micropillar compression investigation into the plastic flow properties of additively manufactured alloys

Shi-Hao Li et al.

Summary: Solidification cells and a high density of dislocations play important roles in determining the plastic properties of additively manufactured alloys. It has been found that the high density of dislocations, arranged in a network or distributed uniformly, determines the yield strength of the alloys, while the variations in cell boundaries have no effect.

ACTA MATERIALIA (2022)

Add to Collection

Article Engineering, Mechanical

Effects of thermal history on sensitization behavior and Charpy impact property of type 316L and 316 stainless steels for applications in a fired heater

N. Bunchoo et al.

Summary: This study compares the sensitization behavior and impact properties of 316L and 316 stainless steel treated at different temperatures. The results show that 316L stainless steel has lower sensitization and higher impact energy, while 316 stainless steel exhibits the opposite.

ENGINEERING FAILURE ANALYSIS (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Review on corrosion performance of laser powder-bed fusion printed 316L stainless steel: Effect of processing parameters, manufacturing defects, post-processing, feedstock, and microstructure

V. B. Vukkum et al.

Summary: The applications of laser-powder bed fusion (LPBF) technique are rapidly increasing, especially in various industries. The focus of research on LPBF printed 316L stainless steel (SS) has mainly been on mechanical properties, with limited attention given to its corrosion behavior. Understanding the influence of processing parameters and feedstock on defects and microstructure is crucial for producing LPBF printed 316L components with reproducible properties.

MATERIALS & DESIGN (2022)

Add to Collection

Article Materials Science, Multidisciplinary

New insights on cellular structures strengthening mechanisms and thermal stability of an austenitic stainless steel fabricated by laser powder-bed-fusion

Thomas Voisin et al.

Summary: The rapid solidification cellular structures in 316L austenitic stainless steels fabricated by laser powder-bed-fusion were found to have specific crystallographic orientations in cell walls, which act as barriers to dislocation movement and contribute to material strengthening. Additionally, oxide precipitates confined inside cell walls also enhance the material's strength. Overall, the understanding of these intrinsic characteristics and strengthening mechanisms can help improve the material's thermal stability and high strength.

ACTA MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of manufacturing parameters and mechanical post-processing on stainless steel 316L processed by laser powder bed fusion

Shahriar Afkhami et al.

Summary: Stainless steel 316L is commonly used in additive manufacturing, particularly via L-PBF, due to its strength-ductility synergy and corrosion resistance. While the material performs well under static, cyclic, and impact loads, further machining or post-processing may be needed to enhance its fatigue performance under cyclic loading.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Experimental determination of solute redistribution behavior during solidification of additively manufactured 316L

Sylvain Depinoy et al.

Summary: The modified WIRS method for processing STEM-EDS data is a strong and reliable technique for characterizing the segregation profile of additively manufactured metals, reducing the experimental uncertainty associated with the quantification of minor elements.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Cold-rolling effects on the microstructure properties of 316L stainless steel parts produced by Laser Powder Bed Fusion (LPBF)

L. Lemarquis et al.

Summary: The study found that the microstructure of 316L produced by LPBF technology undergoes different levels of grain refinement and texture changes after cold-rolling, depending on the initial microstructure. Mechanical twinning was also observed in both microstructures, with a twinned surface ratio exceeding 30%.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical behavior of additively manufactured and wrought 316L stainless steels before and after neutron irradiation

T. S. Byun et al.

Summary: Research was conducted on the mechanical performance of nuclear reactor components fabricated using additive manufacturing methods, with testing conducted before and after neutron irradiation. The AM 316L stainless steel showed hardening and softening after irradiation. The relatively lower strength 316L SS retained higher ductility under irradiation conditions.

JOURNAL OF NUCLEAR MATERIALS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Recrystallization kinetics, mechanisms, and topology in alloys processed by laser powder-bed fusion: AISI 316L stainless steel as example

Leonardo Shoji Aota et al.

Summary: Alloys manufactured by laser powder-bed fusion exhibit intrinsic and hierarchical microstructural features that affect the recrystallization mechanisms. By changing the scanning strategy, it is possible to control the emerging grain patterns. Recrystallization is observed to be slow due to dynamic Zener-Smith pinning, leading to jerky boundary motion, while altering the scanning strategy has an impact on grain topology.

MATERIALIA (2021)

Add to Collection

Article Nanoscience & Nanotechnology

The effect of post-processing heat treatment on the microstructure, residual stress and mechanical properties of selective laser melted 316L stainless steel

Qi Chao et al.

Summary: Additively manufactured 316L austenitic stainless steel was subjected to various heat treatments to study the evolution of residual stress, microstructure, and mechanical properties. Significant compressive residual stress was revealed in the as-built condition, with stress relief achieved at different temperatures. Microstructural changes, such as recrystallization, coarsening of nano-inclusions, and precipitation of embrittling phases, were observed during the heat treatment process, impacting the material's ductility and strength. The study established important relationships between heat treatment, properties, and microstructural changes for the structural application of SLM 316L.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Fracture toughness of 304L austenitic stainless steel produced by laser powder b e d fusion

Punit Kumar et al.

Summary: The study found that 304L austenitic stainless steel manufactured via the LPBF process exhibits high fracture toughness and strength at room temperature due to transformation induced plasticity, but the deformation mechanism changes with increasing temperature, leading to a significant decrease in J values and increased anisotropy.

SCRIPTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Quantitative multiscale correlative microstructure analysis of additive manufacturing of stainless steel 316L processed by selective laser melting

Matjaz Godec et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Multidisciplinary Sciences

The role of side-branching in microstructure development in laser powder-bed fusion

Minh-Son Pham et al.

NATURE COMMUNICATIONS (2020)

Add to Collection

Article Automation & Control Systems

Microstructure and mechanical properties of 316L austenitic stainless steel processed by different SLM devices

A. Roettger et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Calculation and comparison on fracture toughness of specific reliability between ASTM and ISO standards

Si Zhang et al.

MATERIALS RESEARCH EXPRESS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Revealing relationships between porosity, microstructure and mechanical properties of laser powder bed fusion 316L stainless steel through heat treatment

Tobias Ronneberg et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L

K. M. Bertsch et al.

ACTA MATERIALIA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

The Effects of Post-processing in Additively Manufactured 316L Stainless Steels

R. W. Fonda et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Cellular size dependence on the strength of additively manufactured austenitic stainless steel

Decheng Kong et al.

MATERIALS LETTERS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Anisotropy in the microstructure and mechanical property for the bulk and porous 316L stainless steel fabricated via selective laser melting

Decheng Kong et al.

MATERIALS LETTERS (2019)

Add to Collection

Article Engineering, Industrial

Texture control of 316L parts by modulation of the melt pool morphology in selective laser melting

Olivier Andreau et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes

Decheng Kong et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of heat treatment on microstructure and mechanical properties of 316L steel synthesized by selective laser melting

O. O. Salman et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

J-integral Fracture Toughness of High-Mn Steels at Room and Cryogenic Temperatures

Junhyeok Park et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Impact property of high-strength 316L stainless steel with heterostructures

Jiansheng Li et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Crystallographic-orientation-dependent tensile behaviours of stainless steel 316L fabricated by laser powder bed fusion

Xianglong Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Excellent mechanical and corrosion properties of austenitic stainless steel with a unique crystallographic lamellar microstructure via selective laser melting

Shi-Hai Sun et al.

SCRIPTA MATERIALIA (2019)

Add to Collection

Article Nuclear Science & Technology

Microstructure and mechanical properties relationship of additively manufactured 316L stainless steel by selective laser melting

Anne-Helene Puichaud et al.

EPJ NUCLEAR SCIENCES & TECHNOLOGIES (2019)

Add to Collection

Article Chemistry, Physical

Additively manufactured hierarchical stainless steels with high strength and ductility

Y. Morris Wang et al.

NATURE MATERIALS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Oxide inclusions in laser additive manufactured stainless steel and their effects on impact toughness and stress corrosion cracking behavior

Xiaoyuan Lou et al.

JOURNAL OF NUCLEAR MATERIALS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Dislocation network in additive manufactured steel breaks strength-ductility trade-off

Leifeng Liu et al.

MATERIALS TODAY (2018)

Add to Collection

Article Materials Science, Multidisciplinary

High Strength and Ductility of Additively Manufactured 316L Stainless Steel Explained

Md. Shamsujjoha et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Characterization of nano-scale oxides in austenitic stainless steel processed by powder bed fusion

Fuyao Yan et al.

SCRIPTA MATERIALIA (2018)

Add to Collection

Article Electrochemistry

On The Corrosion and Metastable Pitting Characteristics of 316L Stainless Steel Produced by Selective Laser Melting

G. Sander et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Fracture behavior of an austenitic stainless steel with nanoscale deformation twins

L. Xiong et al.

SCRIPTA MATERIALIA (2017)

Add to Collection

Proceedings Paper Engineering, Chemical

Particles control in selective laser melting in-situ oxide dispersion strengthened method

Xin Zhou et al.

1ST INTERNATIONAL CONFERENCE ON NEW MATERIAL AND CHEMICAL INDUSTRY (NMCI2016) (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Failure of metals I: Brittle and ductile fracture

A. Pineau et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel Produced by Selective Laser Melting

R. Casati et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Comparison of microstructure and mechanical properties of 316 L austenitic steel processed by selective laser melting with hot-isostatic pressed and cast material

Arne Roettger et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Oxygen Content Upon the Microstructural and Mechanical Properties of Type 316L Austenitic Stainless Steel Manufactured by Hot Isostatic Pressing

Adam J. Cooper et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2016)

Add to Collection

Article Mechanics

Correlations between Charpy V-notch impact energy and fracture toughness of nuclear reactor pressure vessel (RPV) steels

Meifang Yu et al.

ENGINEERING FRACTURE MECHANICS (2015)

Add to Collection

Article Materials Science, Multidisciplinary

A Microstructural Study on the Observed Differences in Charpy Impact Behavior Between Hot Isostatically Pressed and Forged 304L and 316L Austenitic Stainless Steel

Adam J. Cooper et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)

Add to Collection

Article Mechanics

On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting

A. Riemer et al.

ENGINEERING FRACTURE MECHANICS (2014)

Add to Collection

Article Mechanics

Estimation procedure of J-resistance curves for SE(T) fracture specimens using unloading compliance

Sebastian Cravero et al.

ENGINEERING FRACTURE MECHANICS (2007)

Add to Collection

© Peeref 2019-2024. All rights reserved.