☆ 4.7 Article

High-strength SiC joints fabricated at a low-temperature of 1400°C using a novel low activation filler of Praseodymium

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Effects of interfacial residual stress on mechanical behavior of SiCf/SiC composites

Xiaowu Chen et al.

Summary: Residual stress in boron nitride interphase of continuous SiC fiber-reinforced SiC composites was measured, and it was found that an increase in fabrication temperature leads to increased residual stress, which significantly affects the mechanical properties of the composites.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Materials Science, Ceramics

Dynamic oxidation mechanism of carbon fiber reinforced SiC matrix composite in high-enthalpy and high-speed plasmas

Lingwei Yang et al.

Summary: This study investigated the dynamic oxidation mechanisms of C-f/SiC in high-enthalpy and high-speed plasmas using an inductively coupled plasma wind tunnel. The transition of active/passive oxidations of SiC was identified, and the mechanical properties of C-f/SiC remained stable after long-term dynamic oxidations, indicating its excellent thermal stability for use in thermal protection systems of reusable hypersonic vehicles.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Materials Science, Ceramics

Preparation, microstructure and ion-irradiation damage behavior of Al4SiC4-added SiC ceramics

Huan Liu et al.

Summary: Highly densified SiC ceramics were fabricated by synthesizing single-phase Al4SiC4 powder with low neutron absorption cross section and mixing it with SiC powder, followed by hot pressing. The densification of the ceramics was greatly enhanced by the decomposition of Al4SiC4 and the formation of aluminosilicate liquid phase during sintering. The resulting SiC ceramics exhibited fine equiaxed grains and excellent mechanical properties.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Low-temperature Pr3Si2C2-assisted liquid-phase sintering of SiC with improved thermal conductivity

Jie Xu et al.

Summary: In this study, a novel Pr3Si2C2 additive was prepared and successfully applied in the liquid-phase sintering of SiC ceramics. It was found that an appropriate amount of additive could improve the sintering rate and thermal conductivity of SiC, while excessive additive could decrease the thermal conductivity due to increased interfacial thermal resistance. SiC materials with optimized amount of additive and grain boundary structure exhibited the highest thermal conductivity.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Ultra-high creep resistant SiC ceramics prepared by rapid hot pressing

Pavol Sajgalik et al.

Summary: The high-temperature compression creep properties of additive-free beta/alpha silicon carbide ceramics fabricated by rapid hot pressing were investigated, showing the ceramics had the lowest creep rate reported in the literature within certain temperature and pressure ranges. The average creep activation energy and stress exponent remained constant along the whole range of investigated parameters, suggesting a creep mechanism involving GB sliding accommodated by GB diffusion and beta-alpha SiC phase transformation.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Joining of SiC using CoFeCrNiCuTi high entropy alloy filler by electric current field assisted sintering

Yihe Liu et al.

Summary: SiC ceramics were successfully brazed at lower temperatures using CoFeCrNiCuTi high-entropy alloy and electric field-assisted sintering technology. The inter-diffusion between the filler and ceramics was improved due to the high-entropy effect and the accelerated diffusion of elements. This approach provides a new and efficient filler system for ceramic brazing.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Brazing SiC ceramic to Al0.3CoCrFeNi high-entropy alloy using Ag-Cu filler metal

Jie Sun et al.

Summary: This study successfully achieved reliable brazing of SiC ceramic to Al0.3CoCrFeNi high-entropy alloy using inactive AgCu filler and investigated the influence of interfacial microstructure and brazing temperature on the joint properties.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Effect of low activation rare-earth oxides on sintering of β-SiC

Dengzhou Xu et al.

Summary: The feasibility of sintering beta-SiC at 1850 degrees C using low-activation rare-earth oxides as sintering additives was studied. Pr6O11 was found to be the most effective additive and a mechanism based on liquid phase sintering was proposed. The radiation stability of sintered SiC was also investigated.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Ultrafast low-temperature near-seamless joining of Cf/SiC using a sacrificial Pr3Si2C2 filler via electric current field-assisted sintering technique

Xiaobing Zhou et al.

Summary: A novel layered structure material, Pr3Si2C2, was successfully synthesized using a molten salt approach, and used as a joining filler for carbon fibers reinforced SiC composites. A near-seamless joint was achieved by the newly precipitated SiC grains, which were well densified with the Cf/SiC matrix. The formation of near-seamless joint eliminates the thermal mismatch issues.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Near-seamless joining of Cf/SiC composites using Y3Si2C2 via electric field-assisted sintering technique

Teng Yu et al.

Summary: Y3Si2C2 material was synthesized at a low temperature and used as a joining material for C-f/SiC composites, resulting in near-seamless joints using an electric field-assisted sintering technique.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Review Materials Science, Ceramics

Long-term ceramic matrix composite for aeroengine

Chaokun Song et al.

Summary: This review proposes three strategies to prolong the service life of CMC-SiC thermal-structure components and discusses important factors such as densification, matrix cracking stress, and self-healing component introduction.

JOURNAL OF ADVANCED CERAMICS (2022)

Add to Collection

Article Materials Science, Ceramics

Effects of the joining process on the microstructure and properties of liquid phase-sintered SiC-SiC joints formed with Ti foil

Li-Xiang Wu et al.

Summary: It was found that suitable joining pressure can increase the shear strength of SiC joints, while the joining atmosphere also affects the microstructure and shear strength of the joints. By examining the composition and microstructure of the interlayer, a SiC-SiC joining under argon environment was achieved, offering a cost-effective approach and expanding the applications of SiC ceramic components with complex shapes.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Ytterbium disilicate-based glass-ceramic as joining material for ceramic matrix composites

Federico Smeacetto et al.

Summary: The ceramic matrix composites integration requires a reliable joining technique, with an ytterbium disilicate based glass-ceramic material showing promise for joining SiC/SiC and C/SiC composites. The material exhibits an apparent shear strength of 35 MPa and self-healing behavior at elevated temperatures, making it a potential joining material for CMCs.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Transmission electron microscopy study of extended defect evolution and amorphization in SiC under Si ion irradiation

Jean-Marc Costantini et al.

Summary: This study investigates the damage induced in 3C-SiC epilayers on a silicon wafer by 2.3-MeV Si ion irradiation for different fluences, and deduces the threshold energy densities and irradiation doses for dislocation loop formation and amorphous phase transformation. The role of electronic excitations on the damage recovery at high fluence is also addressed for both SiC and Si.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2021)

Add to Collection

Article Materials Science, Ceramics

Low temperature seamless joining of SiC using a Ytterbium film

Lin-Kun Shi et al.

Summary: The study successfully achieved seamless joining of monolithic SiC at a low temperature using electric field-assisted sintering technology, with Yb coating on SiC forming Yb3Si2C2 to create almost completely seamless joints. The high bending strength of the joints indicates a sound connection, potentially useful for SiC-based composites.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2021)

Add to Collection

Review Materials Science, Ceramics

Progress and challenges towards additive manufacturing of SiC ceramic

Rujie He et al.

Summary: The emergence of additive manufacturing technologies has opened up new avenues for the fabrication of SiC ceramic products. This paper reviews the recent developments in additive manufacturing of SiC ceramic, highlights key challenges, and forecasts potential opportunities for the future. The aim is to provide guidance for the additive manufacturing of SiC ceramic and other structural ceramics.

JOURNAL OF ADVANCED CERAMICS (2021)

Add to Collection

Article Materials Science, Ceramics

Low-temperature joining of SiC ceramics using NITE phase with Al2O3-Ho2O3 additive

Wen-Bin Niu et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Solid-state joining of SiC using a thin Ti3AlC2, TiC, or Ti filler

Pipit Fitriani et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Wetting behavior and brazing of titanium-coated SiC ceramics using Sn0.3Ag0.7Cu filler

Xiaoguo Song et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Pressureless joining of silicon carbide using Ti3SiC2 MAX phase at 1500°C

Hai-Bin Ma et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

Thermodynamic descriptions of the light rare-earth elements in silicon carbide ceramics

Kai Xu et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Almost seamless joining of SiC using an in-situ reaction transition phase of Y3Si2C2

Xiaobing Zhou et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Joining of reaction bonded silicon carbide using self-infiltration of residual Si present in the RBSC

Hyun-Woo Sung et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

A novel high entropy CoFeCrNiCu alloy filler to braze SiC ceramics

Gang Wang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

A novel glass-ceramic with high crystallinity for joining of SiC ceramic

Jian Fang et al.

MATERIALS LETTERS (2020)

Add to Collection

Article Materials Science, Ceramics

High-strength SiC joints with a novel in-situ formed SiC/Al4SiC4 joining filler

Junwen Liu et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Joining of silicon carbide ceramics using a silicon carbide tape

Yong-Hyeon Kim et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Ceramics

Fabrication of highly dense three-layer SiC cladding tube by chemical vapor infiltration method

Pengfei Tao et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Direct bonding of silicon carbide ceramics sintered with yttria

Yong-Hyeon Kim et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Nano-infiltration and transient eutectic (NITE) phase joining SiC ceramics at 1500°C

Li-Xiang Wu et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Pressureless joining of SiC ceramics at low temperature

Li-Xiang Wu et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Effect of Ti addition on the wetting and brazing of Sn0.3Ag0.7Cu filler on SiC ceramic

Mianmian Li et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Seamless joining of silicon carbide ceramics through an sacrificial interlayer Of Dy3Si2C2

Peng Wan et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

SiC ceramics joined with an in-situ reaction gradient layer of TiC/Ti3SiC2 and interface stress distribution simulations

Xiaobing Zhou et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

Residual thermal stress of SiC/Ti3SiC2/SiC joints calculation and relaxed by postannealing

Xiaobing Zhou et al.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Ceramics

Joining of SiC monoliths using a thin MAX phase tape and the elimination of joining layer by solid-state diffusion

Pipit Fitriani et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2018)

Add to Collection

Article Materials Science, Ceramics

Joining of SiCf/SiC using a Ti3AlC2 filler and subsequent elimination of the joining layer

Pipit Fitriani et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

High temperature properties of the monolithic CVD β-SiC materials joined with a pre-sintered MAX phase Ti3SiC2 interlayer via solid-state diffusion bonding

Peter Tatarko et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Thickness-dependent phase evolution and bonding strength of SiC ceramics joints with active Ti interlayer

Hui Yang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Flash joining of CVD-SiC coated Cf/SiC composites with a Ti interlayer

Peter Tatarko et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Review Materials Science, Ceramics

Sintering additives for SiC based on the reactivity: A review

Kati Raju et al.

CERAMICS INTERNATIONAL (2016)

Add to Collection

Article Materials Science, Ceramics

Joining of CVD-SiC coated and uncoated fibre reinforced ceramic matrix composites with pre-sintered Ti3SiC2 MAX phase using Spark Plasma Sintering

Peter Tatarko et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Ceramics

Joining of ceramic matrix composites to high temperature ceramics for thermal protection systems

C. Jimenez et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Fast joining SiC ceramics with Ti3SiC2 tape film by electric field-assisted sintering technology

Xiaobing Zhou et al.

JOURNAL OF NUCLEAR MATERIALS (2015)

Add to Collection

Article Materials Science, Ceramics

Joining of C/SiC composites by spark plasma sintering technique

Stefano Rizzo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2014)

Add to Collection

Article Materials Science, Ceramics

Joining of β-SiC by spark plasma sintering

Salvatore Grasso et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2014)

Add to Collection

Article Materials Science, Ceramics

Microstructure of reaction layer and its effect on the joining strength of SiC/SiC joints brazed using Ag-Cu-In-Ti alloy

Yan Liu et al.

JOURNAL OF ADVANCED CERAMICS (2014)

Add to Collection

Article Materials Science, Coatings & Films

Superhard V-Si-N coatings (>50 GPa) with the cell-like nanostructure prepared by magnetron sputtering

Feng Huang et al.

SURFACE & COATINGS TECHNOLOGY (2013)

Add to Collection

Article Materials Science, Ceramics

Development of SiC-SiC joint by reaction bonding method using SiC/C tapes as the interlayer

Zhaohua Luo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Bonding Mechanisms and Shear Properties of Alumina Ceramic/Stainless Steel Brazed Joint

G. W. Liu et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Silicon carbide composites as fusion power reactor structural materials

L. L. Snead et al.

JOURNAL OF NUCLEAR MATERIALS (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Joining of SiC ceramic-based materials with ternary carbide Ti3SiC2

Hongying Dong et al.

MATERIALS SCIENCE AND ENGINEERING B-ADVANCED FUNCTIONAL SOLID-STATE MATERIALS (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Handbook of SiC properties for fuel performance modeling

Lance L. Snead et al.

JOURNAL OF NUCLEAR MATERIALS (2007)

Add to Collection

Article Materials Science, Ceramics

The fabrication of reaction-formed silicon carbide with controlled microstructure by infiltrating a pure carbon preform with molten Si

YX Wang et al.

CERAMICS INTERNATIONAL (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.