☆ 4.7 Article

Investigation of wireless electrification for a reconfigurable manufacturing cell

JOURNAL OF MANUFACTURING SYSTEMS (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Electrical & Electronic

An Efficient Modeling of Air Gap and Nonlinear Analysis of Magnetic Equivalent Circuit for Large Turbogenerators Under No-Load Condition

Linlin Zhang

Summary: In this article, a fast and accurate modeling method for large turbogenerators is proposed using a 2-D nonlinear magnetic equivalent circuit (MEC) model that considers saturation and rotor motion. The use of continuous fitting function is found to be crucial for the convergence of nonlinear iteration, and a simple and effective MEC for the air gap is provided.

IEEE TRANSACTIONS ON MAGNETICS (2022)

Add to Collection

Article Engineering, Electrical & Electronic

Segmented IPT Coil Design for Continuous Multiple Charging of an Electrified Monorail System

Eun S. Lee et al.

Summary: This article proposes inductive power transfer (IPT) systems based on segmented transmitter (Tx) coils for continuous wireless power delivery to multiple transport robots in an electrified monorail system (EMS). The segmented Tx coil structure allows for flexible installation, easy fabrication, and insensitivity to IPT characteristics. The proposed IPT system uses folded Tx coils and an optimally sized Rx coil to eliminate magnetic dead zones between adjacent Tx coils. Experimental results show that the proposed system achieves higher dc power efficiency compared to conventional Tx coils.

IEEE TRANSACTIONS ON POWER ELECTRONICS (2022)

Add to Collection

Article Automation & Control Systems

A New Coil Structure of Dual Transmitters and Dual Receivers With Integrated Decoupling Coils for Increasing Power Transfer and Misalignment Tolerance of Wireless EV Charging System

Amran Hossain et al.

Summary: This article introduces a new inductive power transfer (IPT) system with dual transmitters and dual receivers, as well as integrated decoupling coils. The proposed decoupling coils not only mitigate the mutual inductances of the same-side coils, but also participate in power transmission, and have good misalignment performance.

IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS (2022)

Add to Collection

Article Engineering, Industrial

Towards automatic configuration and programming of a manufacturing cell

Halldor Arnarson et al.

Summary: Manufacturing industries are evolving towards customized production to create high-quality products with innovative technologies, low prices, and high reliability. Reconfigurable manufacturing systems (RMS) are considered an attractive approach to achieve flexible manufacturing. However, the reconfiguration and programming of RMS are time-consuming and labor-intensive. This paper proposes a highly flexible RMS system with advanced robotics, a digital twin programming interface, and a wireless power transfer (WPT) solution to address these challenges. By reducing human interaction and setup time, this system shows promising potential for new manufacturing lines.

JOURNAL OF MANUFACTURING SYSTEMS (2022)

Add to Collection

Article Engineering, Industrial

Reconfiguring and ramping-up ventilator production in the face of COVID-19: Can robots help?

Ali Ahmad Malik et al.

Summary: This study explores the use of human-robot teams to ramp up ventilator production, presenting a model and design guidelines for faster integration. Evaluation of the scenario through continuous human-robot simulation and amplification of results in a discrete event simulation demonstrates the effectiveness of the approach.

JOURNAL OF MANUFACTURING SYSTEMS (2021)

Add to Collection

Article Engineering, Electrical & Electronic

A Coupling Mechanism With Multidegree Freedom for Bidirectional Multistage WPT System

Jinde Wu et al.

Summary: A bidirectional multistage wireless power transfer (BM-WPT) method is proposed to provide flexible power supply for multiple arm devices, featuring a bowl-coupling structure and three-dimensional orthogonal ring coil arrangement to reduce coupling variation against joint rotation. Special resonant topology design for each stage allows energy to be injected or output freely regardless of energy transfer direction, ultimately reducing sensitivity of output voltages with load variation. Simulation and experimental results confirm the effectiveness of the proposed method.

IEEE TRANSACTIONS ON POWER ELECTRONICS (2021)

Add to Collection

Article Computer Science, Artificial Intelligence

A modular factory testbed for the rapid reconfiguration of manufacturing systems

D. -Y. Kim et al.

JOURNAL OF INTELLIGENT MANUFACTURING (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Full-Range Soft-Switching Pulse Frequency Modulated Wireless Power Transfer

Wei Liu et al.

IEEE TRANSACTIONS ON POWER ELECTRONICS (2020)

Add to Collection

Article Computer Science, Information Systems

Omnidirectional and Efficient Wireless Power Transfer System for Logistic Robots

Zheng Zhang et al.

IEEE ACCESS (2020)

Add to Collection

Article Engineering, Electrical & Electronic

Six-Plate Capacitive Coupler to Reduce Electric Field Emission in Large Air-Gap Capacitive Power Transfer

Hua Zhang et al.

IEEE TRANSACTIONS ON POWER ELECTRONICS (2018)

Add to Collection

Review Engineering, Electrical & Electronic

A Comprehensive Review of Wireless Charging Technologies for Electric Vehicles

Aqueel Ahmad et al.

IEEE TRANSACTIONS ON TRANSPORTATION ELECTRIFICATION (2018)

Add to Collection

Review Energy & Fuels

A Review on the Recent Development of Capacitive Wireless Power Transfer Technology

Fei Lu et al.

ENERGIES (2017)

Add to Collection

Article Engineering, Industrial

Towards a generic design method for reconfigurable manufacturing systems Analysis and synthesis of current design methods and evaluation of supportive tools

Ann-Louise Andersen et al.

JOURNAL OF MANUFACTURING SYSTEMS (2017)

Add to Collection

Article Engineering, Manufacturing

SMART: A System-Level Manufacturing and Automation Research Testbed

Ilya Kovalenko et al.

SMART AND SUSTAINABLE MANUFACTURING SYSTEMS (2017)

Add to Collection

Proceedings Paper Engineering, Industrial

Prerequisites and Barriers for the Development of Reconfigurable Manufacturing Systems for High Speed Ramp-up

Ann-Louise Andersen et al.

3RD ICRM 2016 INTERNATIONAL CONFERENCE ON RAMP-UP MANAGEMENT (2016)

Add to Collection

Article Engineering, Electrical & Electronic

Design Considerations to Reduce Gap Variation and Misalignment Effects for the Inductive Power Transfer System

Cong Zheng et al.

IEEE TRANSACTIONS ON POWER ELECTRONICS (2015)

Add to Collection

Article Engineering, Electrical & Electronic

Inductive Power Transfer

Grant A. Covic et al.

PROCEEDINGS OF THE IEEE (2013)

Add to Collection

Article Engineering, Industrial

Reconfigurable production system design - theoretical and practical challenges

Carin Rosio et al.

JOURNAL OF MANUFACTURING TECHNOLOGY MANAGEMENT (2013)

Add to Collection

Article Automation & Control Systems

SmartFactory-Towards a factory-of-things

Detlef Zuehlke

ANNUAL REVIEWS IN CONTROL (2010)

Add to Collection

Review Engineering, Industrial

Reconfigurable manufacturing systems: the state of the art

Z. M. Bi et al.

INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH (2008)

Add to Collection

© Peeref 2019-2024. All rights reserved.