Related references
Note: Only part of the references are listed.
Article
Materials Science, Ceramics
Essam B. Moustafa et al.
Summary: This study investigated the development of surface nanocomposites using friction stir processing (FSP) to reinforce AA5083 sheets with four different hybrid nanoparticles. The results showed improved mechanical properties and tribological behavior, including enhanced surface hardness, reduced wear resistance, and decreased coefficient of friction. The addition of hybrid nanoparticles resulted in additional grain refinement and the formation of intermetallic phases, leading to significant improvements in the overall performance of the manufactured nanocomposites.
CERAMICS INTERNATIONAL
(2022)
Article
Engineering, Industrial
Qimin Shi et al.
Summary: In-situ preparation of particle reinforced Al matrix composites by laser powder bed fusion is a promising approach to strengthening Al-based alloys. Optimizing laser melting and remelting energy density, combined with high and low-energy laser scanning, can enhance the material's microstructure and mechanical properties. The developed strategy shows potential in obtaining dense materials with fine microstructure and improved mechanical properties during LPBF process.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
(2022)
Article
Nanoscience & Nanotechnology
Wen Cheng et al.
Summary: In this study, composite powders containing nano-TiB2 and nano-TiC particles were prepared by ball milling, and aluminum matrix composites were fabricated by selective laser melting. The addition of nano-TiB2 and nano-TiC particles improved the microstructure and mechanical properties of the material.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Chemistry, Physical
Yingchen Wang et al.
Summary: This study investigates the microstructure evolution and deformation behavior of graphene-based TiC/Ti6Al4V composites processed by friction stir processing. The results reveal uniform microstructure in the stir zone and distinct microstructures at different depths from the processed surface. Special crystallographic orientation relation is observed, and the hardness distribution is found to vary with depth.
APPLIED SURFACE SCIENCE
(2022)
Article
Engineering, Civil
Mohammad Rasool Moazami et al.
Summary: In this study, the microstructure and mechanical properties of Al-15Mg(2)Si-xTiB(2) hybrid composites in different conditions were investigated. The addition of TiB2 improved the as-cast tensile properties, while further additions resulted in a deterioration of tensile properties. Hot deformation and elevated-temperature exposure enhanced the tensile properties by fragmenting, dispersing, and spheroidizing the pseudo-eutectic Mg2Si constituents. The presence of an optimal amount of TiB2 combined with high-temperature thermomechanical processing significantly improved the mechanical properties of the hypereutectic Al-Mg-Si composites.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING
(2022)
Article
Materials Science, Ceramics
Priyaranjan Samal et al.
Summary: This research investigates the synergistic effects of multi-walled carbon nanotubes (CNT) and in-situ synthesized titanium carbide (TiC) on the mechanical performance of aluminum hybrid composites. The study finds that the reinforcement with CNT and TiC significantly improves the micro-hardness, tensile strength, and impact strength of the composites. However, it also results in a decrease in the impact strength. Further analysis reveals the presence of CNT pull-out and CNT bridging effects from the tensile fractography of the composites.
CERAMICS INTERNATIONAL
(2022)
Article
Engineering, Multidisciplinary
Chaolin Tan et al.
Summary: This study investigates the additive manufacturing of SiC-reinforced precipitation hardening steel and explores the effects of SiC content on densification, microstructure evolution, precipitation kinetics, and mechanical properties. The results show that SiC addition promotes in-situ precipitation and enhances the strength of the material through the combination of precipitates, SiC particles, and dislocations.
COMPOSITES PART B-ENGINEERING
(2022)
Article
Chemistry, Physical
Lixia Xi et al.
Summary: Aluminum matrix nanocomposites were manufactured by selective laser melting of MWCNTs modified Al-Mg-Sc-Zr alloys. The addition of MWCNTs influenced the manufacturing quality, phase formation, and mechanical properties of the alloys. The heat-treated MWCNTs/Al-Mg-Sc-Zr nanocomposites exhibited improved mechanical properties due to precipitation strengthening, in-situ synthesis of Al4C3, and favorable interfacial bonding.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Chemistry, Physical
Hongtao Geng et al.
Summary: The hybrid aluminum matrix composites (HAMCs) have gained significant attention due to the synergy between multiple phases. In this study, in-situ AlN-TiC-TiN-Al3Ti/Al inoculation ribbons were prepared and introduced into the Al-Cu-Mn-Ti matrix alloy, leading to improved mechanical properties and refined grain size. The good distribution of nano-particles and the interface matching relationship contribute to the enhanced properties, along with multiple strengthening mechanisms.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Chemistry, Physical
Chang Zhou et al.
Summary: Hybrid Al matrix composites reinforced with ZrW2O8 and SiC reinforcements were fabricated and the effect of SiC content on microstructure, phase composition, thermal expansion, and mechanical properties was investigated. The results showed that composites with a certain SiC content exhibited the best bending strength and near-zero thermal expansion.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Review
Chemistry, Physical
Tatevik Minasyan et al.
Summary: Aluminum alloys, reinforced with ceramic particulates through techniques like laser powder-bed fusion, offer high-performance materials with excellent mechanical properties. The focus of current research is on using additives for grain refinement to enhance the mechanical performance of printed parts.
Article
Chemistry, Physical
Mujian Xia et al.
Summary: In-situ TiC and TiB reinforced titanium matrix composites were fabricated using laser powder fusion, and the influence of scan strategy on their microstructure morphologies and corrosion resistance in NaCl solution was investigated. The results showed that the scan strategy had an impact on the formation of a TiO2 passive layer, with the XY + 90 degrees strategy leading to better corrosion resistance. The corrosion mechanism was discussed based on electrochemical impedance spectroscopy and X-ray photoelectron spectroscopy.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Engineering, Chemical
Ruiqi Wang et al.
Summary: The additive manufacturing method of laser powder bed fusion (LPBF) shows potential in producing high-performance metal matrix nanocomposite components. This study prepared AISHOMg powder with TiB2 nanoparticles by ball milling and optimized the powder properties for better LPBF processability. The optimized nanocomposite powder exhibited favorable forming quality and excellent mechanical properties.
ADVANCED POWDER TECHNOLOGY
(2022)
Article
Crystallography
Zhigang Shen et al.
Summary: In this study, in situ SiC-reinforced Al-Zn-Mg-Cu composites were fabricated by laser powder bed fusion. The effects of SiC content on the microstructure, phase composition, microhardness, and wear resistance were investigated. The results show that increasing SiC content improves the microhardness and wear resistance of the composites.
Review
Materials Science, Multidisciplinary
Paul A. Rometsch et al.
Summary: In recent years, there has been a growing demand in industries for the development of high-strength aluminium alloys for LPBF, but challenges remain in printability and defect control. To achieve high strength with printability, possible strategies include adapting existing high-strength alloys, designing new alloys specifically for LPBF, and developing aluminium-based composites.
MATERIALS & DESIGN
(2022)
Article
Materials Science, Multidisciplinary
Lixia Xi et al.
Summary: In this work, aluminum matrix composites reinforced with (ZrC + TiC) ceramics were successfully fabricated using laser additive manufacturing. The influence of laser power on the properties of the composites was investigated, and the reaction mechanism during the manufacturing process was revealed. The composites prepared at optimal process parameters exhibited high tensile strength and good elongation, attributed to the combined effects of various strengthening mechanisms.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2022)
Article
Chemistry, Physical
Mang Ni et al.
Summary: This study presents a strategy for inhibiting the formation of columnar grains in additively manufactured superalloys. Scandium (Sc) was introduced as an oxide dispersion strengthener (ODS) into Inconel 718 (IN718) alloy to disrupt the typical columnar grains and improve the microstructure and mechanical properties. The addition of Sc resulted in the formation of Sc2O3 nanoparticles and cellular subgrains microstructure, leading to higher yield strength in the as-prepared IN718-Sc alloy.
JOURNAL OF ALLOYS AND COMPOUNDS
(2022)
Article
Materials Science, Multidisciplinary
J. Christudasjustus et al.
Summary: In this study, Al-xV alloys with nanocrystalline structure and high solid solubility of V were synthesized using high-energy ball milling and spark plasma sintering techniques. The microstructure and properties of the alloys were investigated, revealing that the microstructure and hardness were influenced by the sintering temperature, with the formation of a V-lean phase and bimodal grain size observed.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
(2022)
Article
Materials Science, Multidisciplinary
Lizhuang Yang et al.
Summary: The study introduces a novel hybrid reinforcement Cu@GNS-CNTs to graphene/metal system, which enhances the load-bearing capacity of graphene and strain hardening capability of the metal matrix. The organically integrated reinforcing structure exhibits superior load-transfer, fracture inhibition, and dislocation storage capabilities, contributing to the excellent mechanical properties of the composites.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
(2022)
Article
Materials Science, Multidisciplinary
Kefeng Li et al.
Summary: This study comprehensively investigates a novel nano-oxide dispersed Co28Cr9W1.5Si (wt.%) alloy fabricated by laser powder bed fusion. The in-situ formation of Si-rich amorphous nano-oxide inclusions and distinct Co5Cr3Si2 nano-precipitates was observed. The interface between the matrix and the inclusions, as well as their morphologies and microstructure, were thoroughly investigated. The existence of transition boundaries between the inclusions and the matrix effectively hindered the movement of dislocations, leading to an increase in strength. The quantitative analysis revealed a significant contribution to strength caused by the in-situ formed oxide inclusions.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
(2022)
Article
Nanoscience & Nanotechnology
Xiaohui Liu et al.
Summary: In this study, the printability of AA2024-based nanocomposites is improved by incorporating TiC nanoparticles during laser powder bed fusion (LPBF). This approach overcomes the issues of coarse columnar grains and hot cracks typically observed in additive manufacturing of unweldable high-strength aluminum alloys. The addition of TiC nanoparticles not only refines the grain structure and suppresses hot crack formation, but also enhances the mechanical properties of the nanocomposites.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
(2022)
Article
Optics
Lixia Xi et al.
Summary: This study investigates the microstructure evolution and wear properties of MWCNTs/Ti6Al4V composites fabricated by SLM. The addition of MWCNTs enhances the hardness and wear resistance of the composites.
OPTICS AND LASER TECHNOLOGY
(2022)
Proceedings Paper
Materials Science, Multidisciplinary
K. G. Prashanth
Summary: Additive manufacturing processes like selective laser melting (SLM) have gained attention for their ability to produce materials with improved properties and complex shapes. However, processing composites by SLM presents challenges such as defects in process parameters and matrix-reinforcement interaction due to high temperatures.
MATERIALS TODAY-PROCEEDINGS
(2022)
Article
Chemistry, Physical
Junchao Yi et al.
Summary: This study successfully prepared dual-phase reinforced aluminum matrix composites using a novel laser additive manufacturing technology. The feasibility of producing ceramics using a combustion synthesis reaction system was confirmed through selective laser melting, and AlSi10Mg alloy matrix composites were fabricated.
JOURNAL OF ALLOYS AND COMPOUNDS
(2021)
Article
Materials Science, Coatings & Films
Xi Shu et al.
Summary: A novel method using pre-melted electron beam freeform fabrication was proposed to enhance the hardness and wear resistance of Zr alloys by fabricating ZrC-reinforced composites. A graphite diversion nozzle played a critical role in diffusing C from graphite into liquid Zr, leading to the formation of ZrC and consequent fabrication of ZrC/Zr composites. The interface between ZrC and Zr matrix showed negative lattice misfits, with lattice distortion and dispersion strengthening of ZrC contributing to the improved mechanical properties of the composites.
SURFACE & COATINGS TECHNOLOGY
(2021)
Review
Multidisciplinary Sciences
Dongdong Gu et al.
Summary: The advancement of laser-metal additive manufacturing has enabled the printing of multimaterial/multifunctional designs to meet the increasing demand from industries such as aviation, aerospace, automobile manufacturing, and energy production. By integrating material-structure-performance, major improvements in performance and function can be achieved through the right materials printed in the right positions and unique structures printed for unique functions. This approach exemplifies the revolution of design and manufacturing strategies in additive manufacturing.
Article
Materials Science, Multidisciplinary
Lixia Xi et al.
Summary: This study investigated the influence of ceramic nanoparticles on the morphology and size of primary Si phase(s) in AlSi40 alloys manufactured by selective laser melting (SLM). The addition of ceramic nanoparticles resulted in a reduction in the size of primary Si, leading to more homogeneous microhardness distribution and improved mechanical properties. The modified alloy showed increased ultimate compressive strength and maximum compressive strain compared to the unmodified alloy, indicating enhanced performance.
Article
Chemistry, Physical
Yuanyuan Jiang et al.
Article
Materials Science, Multidisciplinary
Lixia Xi et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T
(2020)
Article
Optics
Dongdong Gu et al.
OPTICS AND LASER TECHNOLOGY
(2019)
Article
Materials Science, Multidisciplinary
Ying Yang et al.
MATERIALS & DESIGN
(2018)
Article
Engineering, Manufacturing
E. Ahmadi et al.
JOURNAL OF MANUFACTURING PROCESSES
(2017)
Article
Materials Science, Ceramics
Ying Li et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
(2016)
Article
Materials Science, Ceramics
Ying Li et al.
CERAMICS INTERNATIONAL
(2015)
Article
Materials Science, Ceramics
Ying Li et al.
CERAMICS INTERNATIONAL
(2015)
Article
Materials Science, Ceramics
Shaocun Liu et al.
CERAMICS INTERNATIONAL
(2014)
Article
Engineering, Manufacturing
K. G. Prashanth
MATERIALS AND MANUFACTURING PROCESSES
(2010)
Article
Chemistry, Physical
K. G. Prashanth et al.
JOURNAL OF ALLOYS AND COMPOUNDS
(2009)
