Related references
Note: Only part of the references are listed.Redeposition layer formation caused by shading effect during sputter cleaning and associated damage on rake face of TiN coated high-speed steel drills
J. Kampichler et al.
SURFACE & COATINGS TECHNOLOGY (2022)
Combined experimental and numerical analysis of critical loading conditions for hard metal tool damage in titanium milling
T. Kaltenbrunner et al.
JOURNAL OF MANUFACTURING PROCESSES (2022)
Interface mediated deformation and fracture of an elastic-plastic bimaterial system resolved by in situ transmission scanning electron microscopy
Markus Alfreider et al.
MATERIALS & DESIGN (2022)
Effect of substrate surface texture on adhesion performance of diamond coating
Zhao Zhang et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)
Mode dependent evaluation of fracture behaviour using cantilever bending
Nidhin George Mathews et al.
THEORETICAL AND APPLIED FRACTURE MECHANICS (2021)
Ex Situ Residual Stress Analysis of Chemical Vapor Deposited Diamond Coated Cutting Tools by Synchrotron X-Ray Diffraction in Transmission Geometry
Daniel Hinzmann et al.
ADVANCED ENGINEERING MATERIALS (2021)
Mechanism of adhesion failure during interrupted cutting with cemented carbide tools: Experimental and ab-initio perspective
Siyuan Gao et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2021)
Influence of WC-Co hard metal microstructure on defect density, initiation and propagation kinetics of fatigue cracks starting at intrinsic and artificial defects under a negative stress ratio
T. Kluensner et al.
ACTA MATERIALIA (2020)
Effect of Ta diffusion layer on the adhesion properties of diamond coating on WC-Co substrate
Dan-dan Ma et al.
APPLIED SURFACE SCIENCE (2020)
Micromechanical investigations of CVD coated WC-Co cemented carbide by micropillar compression
Idriss El Azhari et al.
MATERIALS & DESIGN (2020)
Experimentally validated calculation of the cutting edge temperature during dry milling of Ti6Al4V
A. W. Nemetz et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Poisson's ratio of porous and cellular materials with randomly distributed isometric pores or cells
Tereza Uhlirova et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2020)
Novel micro-scale specimens for mode-dependent fracture testing of brittle materials: A case study on GaAs single crystals
J. Ast et al.
MATERIALS & DESIGN (2020)
Effects of three-dimensional Cu/Nb interfaces on strengthening and shear banding in nanoscale metallic multilayers
Y. Chen et al.
ACTA MATERIALIA (2020)
Fatigue behaviour of WC-Co hard metal under stress ratio and effectively loaded volume relevant to metalworking tool failure
T. Kluensner et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)
Influence of localized cyclic substrate plastification on residual stress, load stress and cracking near the interface between hard coating and WC-Co hard metal substrate
T. Kluensner et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2019)
Shot peening-induced plastic deformation of individual phases within a coated WC-Co hard metal composite material including stress-strain curves for WC as a function of temperature
Lukas Faksa et al.
SURFACE & COATINGS TECHNOLOGY (2019)
A review on the mechanical properties for thin film and block structure characterised by using nanoscratch test
Xianfeng Wang et al.
NANOTECHNOLOGY REVIEWS (2019)
Influence of Cobalt on the Adhesion Strength of Polycrystalline Diamond Coatings on WC-Co Hard Alloys
S. A. Linnik et al.
TECHNICAL PHYSICS (2018)
Strength of WC-Co hard metals as a function of the effectively loaded volume
M. Jonke et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2017)
Selective interface toughness measurements of layered thin films
R. Konetschnik et al.
AIP ADVANCES (2017)
Mechanical failure of metal/ceramic interfacial regions under shear loading
Xiaoman Zhang et al.
ACTA MATERIALIA (2017)
ADM guidance-Ceramics: guidance to the use of fractography in failure analysis of brittle materials
Susanne S. Scherrer et al.
DENTAL MATERIALS (2017)
Fatigue life equality of polished and electrical discharge machined WC-Co hard metal achieved solely by wet blasting
T. Kluensner et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2016)
High temperature mechanical properties of WC-Co hard metals
T. Teppernegg et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2016)
Tension behavior of interfaces between ZrCu metallic glass and Si or Zr
C. H. Hsieh et al.
APPLIED SURFACE SCIENCE (2015)
Novel Methods for the Site Specific Preparation of Micromechanical Structures
S. Wurster et al.
PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY (2015)
Residual stress gradients in α-Al2O3 hard coatings determined by pencil-beam X-ray nanodiffraction: The influence of blasting media
Michael Tkadletz et al.
SURFACE & COATINGS TECHNOLOGY (2015)
Analysis of residual stresses and wear mechanism of HF-CVD diamond coated cemented carbide tools
E. Uhlmann et al.
PRODUCTION ENGINEERING-RESEARCH AND DEVELOPMENT (2015)
A review on the mechanical methods for evaluating coating adhesion
Zhaoxiang Chen et al.
ACTA MECHANICA (2014)
Assessing the interfacial strength of an amorphous-crystalline interface
M. C. Liu et al.
ACTA MATERIALIA (2013)
Diamond deposition on hardmetal substrates - Comparison of substrate pre-treatments and industrial applications
R. Haubner et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2010)
Interface fracture properties of thin films studied by using the micro-cantilever deflection technique
Kurt Matoy et al.
SURFACE & COATINGS TECHNOLOGY (2009)
Fracture of ceramics
Robert Danzer et al.
ADVANCED ENGINEERING MATERIALS (2008)
An overview of the potential of quantitative coating adhesion measurement by scratch
SJ Bull et al.
TRIBOLOGY INTERNATIONAL (2006)
The VDI 3198 indentation test evaluation of a reliable qualitative control for layered compounds
N Vidakis et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
The use of the fractal description to characterize engineering surfaces and wear particles
CQ Yuan et al.
WEAR (2003)
Weibull effective volumes and surfaces for cylindrical rods loaded in flexure
GD Quinn
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2003)
Share Paper
