Related references
Note: Only part of the references are listed.The synergetic effects of shot peening and laser-shot peening on the microstructural evolution and fatigue performance of a medium carbon steel
Yating Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2023)
Microstructure and mechanical properties of an Fe-Mn-Al-C lightweight steel after dynamic plastic deformation processing and subsequent aging
Zongyuan Li et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2022)
Microstructures and fatigue behaviors of 25CrNi2MoV steel under electropulsing-assisted ultrasonic surface rolling
Chenfeng Duan et al.
INTERNATIONAL JOURNAL OF FATIGUE (2022)
Evaluation of pre-shot peening on improvement of carburizing heat treatment of AISI 9310 gear steel
Jizhan Wu et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2022)
Ultra-high fatigue property and fracture mechanism of modified 20CrMoH steel by gas carburizing technology combined with shot peening treatment
Jintao Wang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2022)
Sensitive misalignment-based dynamic loaded meshing impact diagnosis mechanism for aviation spiral bevel gear transmission
Han Ding et al.
EXPERT SYSTEMS WITH APPLICATIONS (2022)
Failure analysis of the carburized 20MnCr5 gear in fatigue working condition
Ning Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2022)
Study on the relation between surface integrity and contact fatigue of carburized gears
Xiuhua Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2022)
Ultra-high strength medium-Mn lightweight steel by dislocation slip band refinement and suppressed intergranular ?-carbide with Cr addition
Mingxiang Liu et al.
MATERIALS CHARACTERIZATION (2022)
Effect of shot peening on microstructure and contact fatigue crack growth mechanism of shaft steel
Shengguan Qu et al.
MATERIALS CHEMISTRY AND PHYSICS (2021)
Determination of the mode I crack tip opening rate and the rate dependent cohesive properties for structural adhesive joints using digital image correlation
Fengzhen Sun et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2021)
Effect of shot peening on residual stress distribution and tribological behaviors of 17Cr2Ni2MoVNb steel
Yalong Zhang et al.
SURFACE & COATINGS TECHNOLOGY (2020)
Effect of phase in surface layers on rotating-bending fatigue strength of SCM415 steel after austenitic nitriding
Yasushi Hiraoka
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Crack initiation mechanism in ultrafine-grained copper fabricated by severe plastic deformation in the high-cycle fatigue regime
M. Goto et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Experimental study on surface integrity of ultra-high-strength steel by ultrasonic hot rolling surface strengthening
Xiaosheng Luan et al.
SURFACE & COATINGS TECHNOLOGY (2020)
Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening
Yalong Zhang et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Analytical theory for fatigue crack propagation rates of mixed-mode I-II cracks and its application
S. Qi et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Improving the fretting and corrosion fatigue performance of 300M ultra-high strength steel using the ultrasonic surface rolling process
Weidong Zhao et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Effect of ultrasonic surface rolling on microstructure and rolling contact fatigue behavior of 17Cr2Ni2MoVNb steel
Ya-Long Zhang et al.
SURFACE & COATINGS TECHNOLOGY (2019)
The influence of ultrasonic surface rolling on the fatigue and wear properties of 23-8N engine valve steel
Fuqiang Lai et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Deformation behaviour and texture evolution of martensite steel subjected to hard milling
Binxun Li et al.
MATERIALS CHARACTERIZATION (2019)
Effect of ultrasonic nanocrystal surface modification on elevated temperature residual stress, microstructure, and fatigue behavior of ATI 718Plus alloy
Micheal Kattoura et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Fatigue stress concentration sensitivity and stress ratio effect of a 40CrNi2Si2MoVA steel
Yukui Gao
MATERIALS LETTERS (2017)
Effect of laser shock peening on bending fatigue performance of AISI 9310 steel spur gear
Chong Peng et al.
OPTICS AND LASER TECHNOLOGY (2017)
Fatigue strength evaluation of small defect at stress concentration
Mari Aman et al.
3RD INTERNATIONAL SYMPOSIUM ON FATIGUE DESIGN AND MATERIAL DEFECTS (FDMD 2017) (2017)
Effect of wet shot peening on Ti-6Al-4V alloy treated by ceramic beads
Guo-qing Chen et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2014)
High-pressure torsion of pure metals: Influence of atomic bond parameters and stacking fault energy on grain size and correlation with hardness
Kaveh Edalati et al.
ACTA MATERIALIA (2011)
Thermally activated dislocation dynamics in austenitic FeMnC steels at low homologous temperature
S. Allain et al.
SCRIPTA MATERIALIA (2010)