☆ 4.6 Article

Development of novel Al-Si-Ce filler wires to enable high contrast in X-ray imaging of fusion welded aluminum alloy joints

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Effect of Ce addition on microstructure, thermal and mechanical properties of Al-Si alloys

Sezgin Cengiz et al.

Summary: The effect of cerium (Ce) content on the microstructure and properties of commercial Al-12Si and Al-12Si-xCe alloys was investigated. Adding Ce resulted in a decrease in the coefficient of thermal expansion and the formation of additional phases. The ultimate tensile strength of the alloy increased with the addition of 2 wt% Ce, but decreased with further addition of Ce.

MATERIALS TODAY COMMUNICATIONS (2023)

Add to Collection

Article Materials Science, Characterization & Testing

Novel non-destructive technique for detecting the weld fusion zone using a filler wire of high x-ray contrast

J. Galos et al.

Summary: This study demonstrates a novel method that provides contrast between the Al substrate and weld fusion zone in x-ray images by incorporating a dopant element in the filler wire with a higher x-ray attenuation coefficient. This technique enables the detection of penetration depth and weld throat more accurately than conventional methods.

NDT & E INTERNATIONAL (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Thermal stability of aluminum-cerium binary alloys containing the Al-Al11Ce3 eutectic

Frank Czerwinski

Summary: The strength retention of Al-Ce binary alloys at high temperatures was assessed compared to A380 alloy and pure Al. The Al11Ce3 eutectic and proeutectic phases were found to have limited effectiveness in strengthening Al-Ce alloys at room temperature and retaining their strength at increased temperatures. Despite the high hardness retention ratio of Al-Ce alloys, the yield stress decreased with testing temperatures.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Study of Solidification Thermal Analysis, Microstructure and Mechanical Characteristics of A384 Cast Alloy Treated with Rare Earth (Sm, Tb, Ce and La) Elements

Mahmoud Tash et al.

Summary: This article investigates the refining and modification response of cast A384 aluminium alloy induced by the addition of rare earth elements and the impact on microstructural and mechanical performance. It is observed that the added rare earth metals Sm plus Tb to A384 alloy improved the alloy strength and hardness due to their refining and modification effect. Furthermore, enhancement of both wear and corrosion resistance is achieved through the addition of 1.0 wt.% Samarium (Sm) to A384 samples.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Review Materials Science, Multidisciplinary

Profilometry-Based Inverse Finite Element Method Indentation Plastometry

Trevor William Clyne et al.

Summary: This review examines the current state-of-the-art in extracting the stress-strain relationship of a metallic sample from indentation experiments, utilizing a high load and large spherical indenter. The process involves measuring the indent profile and using it for inverse FEM modeling to obtain the best fit parameter values for a constitutive plasticity law. Commercial products now offer automated operations, but implementing and optimizing these procedures still involve various practical challenges.

ADVANCED ENGINEERING MATERIALS (2021)

Add to Collection

Article Materials Science, Characterization & Testing

An enhancement framework based on gradient domain tone mapping and fuzzy logical for X-ray image of complex workpiece

Yi Liu et al.

Summary: A proposed enhancement framework in this paper utilizes logarithm transformation, gradient domain tone mapping, and fuzzy enhancement operator to improve the visual quality of X-ray images, particularly suitable for defect inspection of complex workpieces.

NDT & E INTERNATIONAL (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Rare Earth Metals on the Mechanical Properties and Fractography of Al-Si-Based Alloys

M. F. Ibrahim et al.

INTERNATIONAL JOURNAL OF METALCASTING (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Cerium in aluminum alloys

Frank Czerwinski

JOURNAL OF MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Critical Assessment 36: Assessing differences between the use of cerium and scandium in aluminium alloying

Frank Czerwinski

MATERIALS SCIENCE AND TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Characterization & Testing

Variable Zoom technique for X-Ray Computed Tomography

Yuri Nikishkov et al.

NDT & E INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Characterization & Testing

Quantitative non-destructive evaluation of drilling defects in SiCf/SiC composites using low-energy X-ray imaging technique

Feifei Liu et al.

NDT & E INTERNATIONAL (2020)

Add to Collection

Article Engineering, Environmental

Anticipating impacts of introducing aluminum-cerium alloys into the United States automotive market

Ruby T. Nguyen et al.

RESOURCES CONSERVATION AND RECYCLING (2019)

Add to Collection

Review Automation & Control Systems

Quality assessment in laser welding: a critical review

John Stavridis et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Materials Science, Characterization & Testing

Accurate defect detection via sparsity reconstruction for weld radiographs

Benzhi Chen et al.

NDT & E INTERNATIONAL (2018)

Add to Collection

Article Engineering, Mechanical

Recent results on fatigue strength improvement of high-strength steel welded joints

Halid Can Yildirim

INTERNATIONAL JOURNAL OF FATIGUE (2017)

Add to Collection

Article Materials Science, Characterization & Testing

Automated detection of welding defects in pipelines from radiographic images DWDI

Neury Boaretto et al.

NDT & E INTERNATIONAL (2017)

Add to Collection

Article Optics

An improved version of Otsu's method for segmentation of weld defects on X-radiography images

Muthukumaran Malarvel et al.

OPTIK (2017)

Add to Collection

Article Chemistry, Multidisciplinary

High performance aluminum-cerium alloys for high-temperature applications

Zachary C. Sims et al.

MATERIALS HORIZONS (2017)

Add to Collection

Article Engineering, Electrical & Electronic

Anisotropic diffusion based denoising on X-radiography images to detect weld defects

Muthukumaran Malarvel et al.

DIGITAL SIGNAL PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

A criterion for cracking during solidification

Sindo Kou

ACTA MATERIALIA (2015)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

EFFECT OF WELD PENETRATION ON FATIGUE LIFE

A. R. Deshmukh et al.

12TH GLOBAL CONGRESS ON MANUFACTURING AND MANAGEMENT (GCMM - 2014) (2014)

Add to Collection

Article Materials Science, Characterization & Testing

Automatic weld defect identification from radiographic images

O. Zahran et al.

NDT & E INTERNATIONAL (2013)

Add to Collection

Article Chemistry, Physical

Effect of Ce on solidification and mechanical properties of A360 alloy

Maja Voncina et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

Add to Collection

Article Materials Science, Characterization & Testing

Welding defect detection from radiography images with a cepstral approach

H. Kasban et al.

NDT & E INTERNATIONAL (2011)

Add to Collection

Article Materials Science, Characterization & Testing

Improving the accuracy of computer-aided radiographic weld inspection by feature selection

T. Warren Liao

NDT & E INTERNATIONAL (2009)

Add to Collection

Article Materials Science, Characterization & Testing

An automatic system of classification of weld defects in radiographic images

Rafael Vilar et al.

NDT & E INTERNATIONAL (2009)

Add to Collection

Article Chemistry, Physical

Al-ce-si (Aluminum-Cerium-Silicon)

V. Raghavan

JOURNAL OF PHASE EQUILIBRIA AND DIFFUSION (2007)

Add to Collection

Article Materials Science, Characterization & Testing

Pattern recognition of weld defects detected by radiographic test

RR da Silva et al.

NDT & E INTERNATIONAL (2004)

Add to Collection

Article Materials Science, Multidisciplinary

Thermodynamic aspects of the constitution, grain refining, and solidification enthalpies of Al-Ce-Si alloys

J Gröbner et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)

Add to Collection

Article Engineering, Industrial

Light-weight structures produced by laser beam joining for future applications in automobile and aerospace industry

E Schubert et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.