☆ 4.7 Article

Electric arc gasification of pyrolysis oil with the production of hydrogen-enriched synthesis gas and carbon nanomaterial

FUEL PROCESSING TECHNOLOGY (2023)

Related references

Note: Only part of the references are listed.

Article Chemistry, Analytical

Catalytic pyrolysis of Reutealis trisperma oil using raw dolomite for bio-oil production

Yorinda Buyang et al.

Summary: Conversion of non-edible RTO into bio-oil by catalytic pyrolysis using dolomite as a catalyst, without prior calcination or treatment. Dolomite enhanced bio-oil yield and reduced char formation at higher pyrolysis temperatures. Dolomite also improved the composition and physical properties of bio-oil, including viscosity, calorific value, and density, and reduced the carboxylic acid content through esterification reaction.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2023)

Add to Collection

Article Chemistry, Physical

Optimization of two bio-oil steam reforming processes for hydrogen production based on thermodynamic analysis

Panlei Wang et al.

Summary: The thermodynamics of hydrogen production from bio-oil in conventional steam reforming and sorption-enhanced steam reforming methods was investigated. Factors such as reforming temperature, S/C ratio, and operating pressure significantly influence hydrogen yield, with SE-SR showing advantages of higher yield at lower temperatures and carbon suppression compared to C-SR.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2022)

Add to Collection

Article Engineering, Environmental

An investigation into the preparation of carbon black by partial oxidation of spent tyre pyrolysis oil

Chiemeka Onyeka Okoye et al.

Summary: This study prepared carbon black using a drop tube furnace to promote the use of recycled waste materials as an industrial feedstock. The yield and properties of the carbon black were found to be affected by reaction temperature, oxygen concentration, and residence time. Characterization showed that the carbon black produced from recycled waste materials had comparable properties to commercial products, indicating its potential for use in circular economy strategies.

WASTE MANAGEMENT (2022)

Add to Collection

Article Engineering, Environmental

Comparative Analysis of the Characteristics of Carbonaceous Material Obtained via Single-Staged Steam Pyrolysis of Waste Tires

Kirill B. Larionov et al.

Summary: The study focused on the characteristics of carbonaceous material obtained by single-staged steam pyrolysis of waste tires, revealing that the samples had similar properties and structure. The research provides theoretical support for the development of technology in this area to simplify the tire recycling process.

JOURNAL OF THE AIR & WASTE MANAGEMENT ASSOCIATION (2022)

Add to Collection

Article Environmental Sciences

Liquid Hydrocarbons Production by the Steam Pyrolysis of Used Tires: Energy Characteristics and Environmental Sustainability

K. B. Larionov et al.

Summary: The technical characteristics and combustion process of liquid hydrocarbons obtained by steam pyrolysis of used automobile tires were studied, and compared to traditional liquid fuel oil. The liquid hydrocarbons showed low pour point, comparable calorific value, shorter ignition delay time, and burning time. The combustion process of these liquid hydrocarbons was found to be superior to traditional liquid fuel.

WASTE AND BIOMASS VALORIZATION (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Steam Pyrolysis of Oil Sludge for Energy-Valuable Products

Kirill Larionov et al.

Summary: Experimental studies were conducted on the steam pyrolysis of oil sludge using a flowtype pilot plant. Valuable energy products including liquid hydrocarbons, semi-coke, non-condensable gas-phase compounds, and bitumen were obtained. The physicochemical characteristics, atomization process, droplet ignition, and combustion of the liquid hydrocarbons were comprehensively studied. This study is of great importance for the design of new installations and technological systems for hydrocarbon pyrolysis.

APPLIED SCIENCES-BASEL (2022)

Add to Collection

Article Chemistry, Applied

A novel approach of waste tires rubber utilization via ambient air direct current arc discharge plasma

A. Ya Pak et al.

Summary: The study proposes a method for obtaining ultrafine carbon product and gas mixture through generating electric arc plasma in open-air environment, aiming to address the global issue of waste tires rubber utilization. Experimental results demonstrate that this approach simplifies design, reduces energy consumption, and yields high quality carbon powder and gas mixture.

FUEL PROCESSING TECHNOLOGY (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Plasma-Catalytic Reforming of Naphthalene and Toluene as Biomass Tar over Honeycomb Catalysts in a Gliding Arc Reactor

Danhua Mei et al.

Summary: This study proposes a hybrid plasma-catalytic system for steam reforming of tar compounds over honeycomb-based catalysts in a gliding arc discharge (GAD) reactor. The presence of Ni/γ-Al2O3 gives the best performance with high conversions of toluene and naphthalene, and yields of H2 and CO while inhibiting the formation of byproducts. Characterization of the used catalyst shows strong carbon resistance and excellent stability of the honeycomb material coated with Ni/γ-Al2O3.

ACS SUSTAINABLE CHEMISTRY & ENGINEERING (2022)

Add to Collection

Review Chemistry, Physical

The future of hydrogen energy: Bio-hydrogen production technology

Xianxian Xu et al.

Summary: The widespread use of non-renewable energy has led to serious environmental problems. Hydrogen, as a carbon-free fuel, is considered the most promising energy carrier for the future. However, the current production of hydrogen is dominated by fossil-based techniques, which have low conversion efficiency and greenhouse gas emissions. Therefore, finding green and sustainable production routes for hydrogen with low energy consumption and cost is crucial. Bio-hydrogen production technologies have environmental advantages and broad prospects, with each technique having its own advantages, challenges, and applicability.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2022)

Add to Collection

Article Green & Sustainable Science & Technology

An advanced coal-based zero-emission polygeneration system using water-gas shift reaction and syngas recycle to achieve different methanol and electricity distributions

Tuantuan Xin et al.

Summary: This study proposes an advanced polygeneration system that combines methanol synthesis and the Allam cycle in order to achieve coal utilization with zero carbon emissions. By connecting the coal-to-methanol process and the Allam cycle, the energy penalty of carbon dioxide separation in methanol production is reduced to zero. The combined system improves energy conversion performance and enhances the distribution of different products, such as methanol and electric power.

JOURNAL OF CLEANER PRODUCTION (2022)

Add to Collection

Review Green & Sustainable Science & Technology

Manufacturing of carbon black from spent tyre pyrolysis oil e A literature review

Chiemeka Onyeka Okoye et al.

Summary: Carbon black is a significant industrial chemical used for various applications such as elastomer reinforcement, conductive filler, coating agent, and dyeing agent. While current production relies on fossil fuel-based resources, there is a growing interest in utilizing renewable sources and recycled wastes for cleaner production and reduced costs.

JOURNAL OF CLEANER PRODUCTION (2021)

Add to Collection

Review Chemistry, Physical

A comprehensive review on the prospects of multi-functional carbon nano onions as an effective, high- performance energy storage material

Vivek Dhand et al.

Summary: This review provides an update on the current and novel developments of carbon nano onions (CNOs) in recent years, including synthesis routes, growth mechanisms, purification methods, properties, applications, research trends, and market analysis.

CARBON (2021)

Add to Collection

Article Chemistry, Analytical

Chemical recycling of end-of-life tires by intermediate pyrolysis using a twin-auger reactor: Validation in a laboratory environment

Juan Daniel Martinez et al.

Summary: This study validated the operational features of a twin-auger pyrolyzer and the characteristics of the resulting products for the chemical recycling of end-of-life tires. Through 27 experiments, optimal conditions were determined, and detailed physicochemical property analyses were conducted on the products.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2021)

Add to Collection

Article Green & Sustainable Science & Technology

Combustion and emission characteristics of diesel engine fueled with nanocatalyst and pyrolysis oil produced from the solid plastic waste using screw reactor

Manigandan Sekar et al.

Summary: This study focused on extracting plastic oil from mixed plastic waste and using nanoparticles to improve the quality of waste pyrolysis oil. The addition of Fe2O3 doped Al2O3 increased brake power production by 35% and reduced emissions of HC and CO2 by 45% and 60% respectively. The NOx emissions were also reduced by 15% compared to neat plastic oil and diesel fuel when using 25% pyrolysis oil.

JOURNAL OF CLEANER PRODUCTION (2021)

Add to Collection

Review Engineering, Environmental

A Review on Additives-assisted Ultrasound for Organic Pollutants Degradation

Xiaohui Lu et al.

Summary: Considerable attention has been paid to sonochemical advanced oxidation processes (SAOPs) for pollutants removal in the past 2 decades. SAOPs are effective methods for degrading refractory pollutants by generating free radicals such as •OH and •H through water pyrolysis, and high temperature and pressure in cavitation bubbles. Various additives have been used to enhance sonochemical pollutants degradation. This paper reviews the efficiency of ultrasound (US) alone and sono-hybrid systems in degrading pollutants, focusing on the reaction mechanisms of additives for improving degradation. Challenges and research needs for applying SAOPs for removing organic pollutants from aquatic systems are discussed.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Add to Collection

Article Thermodynamics

Global vision from the thermodynamics of the effect of the bio-oil composition and the reforming strategies in the H2 production and the energy requirement

Leire Landa et al.

Summary: The study compares the yield of H-2 and by-products in the reforming of different oxygenates in bio-oil through thermodynamic analysis, focusing on steam reforming, oxidative steam reforming, and autothermal reforming. The results show that S/C = 5 and the temperature range of 610-644 degrees Celsius are the most suitable conditions for high equilibrium H-2 yield. Inert gas addition at a S/C ratio of 1.5 slightly increases hydrogen yield and decreases coke formation, but this effect is not significant for S/C ratios above 5.

ENERGY CONVERSION AND MANAGEMENT (2021)

Add to Collection

Article Environmental Sciences

Recovery of carbon black from waste tire in continuous commercial rotary kiln pyrolysis reactor

Junqing Xu et al.

Summary: This study examines the properties of carbon black from waste tires continuous commercial scale pyrolysis, aiming to contribute to the field and provide insights into the feasibility of commercial pyrolysis and operation methods.

SCIENCE OF THE TOTAL ENVIRONMENT (2021)

Add to Collection

Article Chemistry, Physical

Hydrogen production from a solution plasma process of bio-oil

Heejin Lee et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2020)

Add to Collection

Article Chemistry, Physical

A density functional theory study on the conversion of polycyclic aromatic hydrocarbons in hydrogen plasma

Lu Chen et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2020)

Add to Collection

Article Materials Science, Coatings & Films

Cubic SiC nanowire synthesis by DC arc discharge under ambient air conditions

Alexander Pak et al.

SURFACE & COATINGS TECHNOLOGY (2020)

Add to Collection

Review Agricultural Engineering

Pyrolysis synergy of municipal solid waste (MSW): A review

Duu-Jong Lee et al.

BIORESOURCE TECHNOLOGY (2020)

Add to Collection

Article Chemistry, Physical

Further insight into some properties of pyrolytic carbon black obtained from scrap truck tires

Franco Cataldo

FULLERENES NANOTUBES AND CARBON NANOSTRUCTURES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Vacuumless synthesis of tungsten carbide in a self-shielding atmospheric plasma of DC arc discharge

A. Ya Pak et al.

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Catalysis-free transformation of non-graphitising carbons into highly crystalline graphite

Jason L. Fogg et al.

COMMUNICATIONS MATERIALS (2020)

Add to Collection

Review Thermodynamics

Progress in waste utilization via thermal plasma

Vineet Singh Sikarwar et al.

PROGRESS IN ENERGY AND COMBUSTION SCIENCE (2020)

Add to Collection

Article Thermodynamics

Effects of sewage sludge organic and inorganic constituents on the properties of pyrolysis products

W. D. Chanaka Udayanga et al.

ENERGY CONVERSION AND MANAGEMENT (2019)

Add to Collection

Article Environmental Sciences

Pyrolysis wastewater treatment by adsorption on biochars produced by poplar biomass

Benedetta de Caprariis et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2017)

Add to Collection

Article Biotechnology & Applied Microbiology

Valorization of pyrolysis water: a biorefinery side stream, for 1,2-propanediol production with engineered Corynebacterium glutamicum

Julian Lange et al.

BIOTECHNOLOGY FOR BIOFUELS (2017)

Add to Collection

Article Thermodynamics

Potential of pyrolysis processes in the waste management sector

D. Czajczynska et al.

THERMAL SCIENCE AND ENGINEERING PROGRESS (2017)

Add to Collection

Review Chemistry, Physical

Transforming waste into carbon-based nanomaterials

Junjiao Deng et al.

CARBON (2016)

Add to Collection

Article Agricultural Engineering

Entrained flow gasification of straw- and wood-derived pyrolysis oil in a pressurized oxygen blown gasifier

E. J. Leijenhorst et al.

BIOMASS & BIOENERGY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Synthesis of thin bundled single walled carbon nanotubes and nanohorn hybrids by arc discharge technique in open air atmosphere

Joseph A. Berkmans et al.

DIAMOND AND RELATED MATERIALS (2015)

Add to Collection

Article Chemistry, Physical

Gasification of corn cob using non-thermal arc plasma

Changming Du et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2015)

Add to Collection

Article Chemistry, Multidisciplinary

Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report)

Matthias Thommes et al.

PURE AND APPLIED CHEMISTRY (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Arc discharge synthesis of carbon nanotubes: Comprehensive review

Neha Arora et al.

DIAMOND AND RELATED MATERIALS (2014)

Add to Collection

Article Engineering, Environmental

Production of high quality syngas from argon/water plasma gasification of biomass and waste

M. Hlina et al.

WASTE MANAGEMENT (2014)

Add to Collection

Article Chemistry, Physical

Arc synthesis of double-walled carbon nanotubes in low pressure air and their superior field emission properties

Jiang Zhao et al.

CARBON (2013)

Add to Collection

Article Energy & Fuels

Experimental Study of Carbon Black and Diesel Engine Soot Oxidation Kinetics Using Thermogravimetric Analysis

Hom N. Sharma et al.

ENERGY & FUELS (2012)

Add to Collection

Article Chemistry, Physical

Comparative XRD, Raman, and TEM Study on Graphitization of PBO-Derived Carbon Fibers

M. Beatriz Vazquez-Santos et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2012)

Add to Collection

Article Nanoscience & Nanotechnology

Continuous and low-cost synthesis of high-quality multi-walled carbon nanotubes by arc discharge in air

Jiang Zhao et al.

PHYSICA E-LOW-DIMENSIONAL SYSTEMS & NANOSTRUCTURES (2012)

Add to Collection

Article Thermodynamics

Effects of syngas type on the operation and performance of a gas turbine in integrated gasification combined cycle

Young Sik Kim et al.

ENERGY CONVERSION AND MANAGEMENT (2011)

Add to Collection

Article Engineering, Mechanical

Thermogravimetric analysis of carbon black and engine soot-Towards a more robust oil analysis method

Arne Bredin et al.

TRIBOLOGY INTERNATIONAL (2011)

Add to Collection

Article Chemistry, Physical

Synthesis of single-wall carbon nanohorns by arc-discharge in air and their formation mechanism

Nan Li et al.

CARBON (2010)

Add to Collection

Review Chemistry, Physical

Hydrogen production by methane decomposition: A review

Hazzim F. Abbas et al.

INTERNATIONAL JOURNAL OF HYDROGEN ENERGY (2010)

Add to Collection

Article Materials Science, Multidisciplinary

High yield formation of carbon nanotubes using a rotating cathode in open air

Ravi Joshi et al.

DIAMOND AND RELATED MATERIALS (2008)

Add to Collection

Review Thermodynamics

Biofuels (alcohols and biodiesel) applications as fuels for internal combustion engines

Avinash Kumar Agarwal

PROGRESS IN ENERGY AND COMBUSTION SCIENCE (2007)

Add to Collection

Article Chemistry, Analytical

Pyrolysis and combustion of waste lubricant oil from diesel cars:: Decomposition and pollutants

M. J. Fuentes et al.

JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2007)

Add to Collection

Article Chemistry, Physical

Studying disorder in graphite-based systems by Raman spectroscopy

M. A. Pimenta et al.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2007)

Add to Collection

Article Chemistry, Physical

Preparation of activated carbons from used tyres by gasification with steam and carbon dioxide

Juan F. Gonzalez et al.

APPLIED SURFACE SCIENCE (2006)

Add to Collection

Article Materials Science, Multidisciplinary

Carbon nanotubes and other fullerenes produced from tire powder injected into an electric arc

LE Murr et al.

MATERIALS CHARACTERIZATION (2005)

Add to Collection

Article Chemistry, Physical

Raman micro spectroscopy of soot and related carbonaceous materials:: Spectral analysis and structural information

A Sadezky et al.

CARBON (2005)

Add to Collection

Article Polymer Science

Entropy penalty-induced self-assembly in carbon black or carbon fiber filled polymer blends

GZ Wu et al.

MACROMOLECULES (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.