☆ 4.7 Article

Effect of powder column height on the compression behavior of rice husk powder under gas pressurization

FUEL (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Chemical

Stress distribution in a powder column under uniaxial compression

Amalia Thomas et al.

Summary: The distribution of stresses transmitted by compressed powder onto the containing vessel base and side walls is investigated in this study. It is found that a uniform pressure on the base is only achieved when the compressed powder column is taller than a critical value. Additionally, high radial stresses are measured on the vessel side wall in the region below the piston.

POWDER TECHNOLOGY (2022)

Add to Collection

Article Engineering, Chemical

Experimental study on the alumina fine powder internal compression characteristics under gas pressurization

Shicheng Wang et al.

Summary: The study found that the pressurization rate affects the compression characteristics of powder beds, with different positions in the beds exhibiting different compression characteristics and the compression ratio increasing with bed depth. A prediction model for relative compaction density variation was established based on the research results.

POWDER TECHNOLOGY (2022)

Add to Collection

Article Engineering, Chemical

Experimental study on the effects of particle characteristics and pressurization methods on powder compression

Shicheng Wang et al.

Summary: Both particle characteristics and pressurization methods have a significant impact on powder compression behavior. The compressibility of powder with different average particle sizes, sphericity, and adhesion was experimentally investigated. The results show that smaller particle size, higher sphericity, and greater adhesion lead to higher compressibility of the powder. Gas pressurization has a smaller effect on powder compression compared to mechanical pressurization. The relationship between normal stress and gas pressurization rate was proposed, and the mechanism of different pressurization methods was discussed.

CHEMICAL ENGINEERING SCIENCE (2022)

Add to Collection

Article Engineering, Chemical

Biomass feeding in a dilute pneumatic conveying system

Thais L. C. Gomes et al.

Summary: The study designed a feeding system for controlling biomass flow rate and evaluated the feeding efficiency of different biomasses under various conditions. Low bulk density biomass showed higher feeding efficiencies at lower silo heights, while high-density biomass performed better at greater heights.

POWDER TECHNOLOGY (2021)

Add to Collection

Article Engineering, Chemical

Analyzing bulk density and void fraction: B. Effect of moisture content and compression pressure

Haim Kalman et al.

Summary: This study investigates the impact of moisture content and compression pressure on bed void fraction in different materials. The Archimedes number was identified as a suitable parameter for describing particle behavior, as well as the effects of moisture content and compression pressure. General equations were developed to assess liquid bridge forces in solid and porous particles, as well as describe compressed particulate beds based on the Heckel model. The study also examined the compression of wet particles, with the general equations aligning well with experimental values.

POWDER TECHNOLOGY (2021)

Add to Collection

Review Engineering, Chemical

Flow behavior characterization of biomass Feedstocks

Ziwei Cheng et al.

Summary: The key to successful biomass handling processes lies in understanding the flow behavior of different feedstocks as functions of critical material properties, environmental conditions, and processing parameters. Factors such as particle size, shape, moisture, temperature, and handling equipment all substantially influence biomass flowability. Current limitations in studies and potential methods to overcome them have been presented.

POWDER TECHNOLOGY (2021)

Add to Collection

Article Engineering, Chemical

Approach the powder contact force, voidage, tensile stress, wall frictional stress and state diagram of powder bed by simple pressure drop monitoring

Wan-Yi Hsu et al.

ADVANCED POWDER TECHNOLOGY (2020)

Add to Collection

Review Biotechnology & Applied Microbiology

Advances in thermochemical conversion of woody biomass to energy, fuels and chemicals

Shusheng Pang

BIOTECHNOLOGY ADVANCES (2019)

Add to Collection

Review Green & Sustainable Science & Technology

Global challenges in the sustainable development of biomass gasification: An overview

S. K. Sansaniwal et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2017)

Add to Collection

Article Engineering, Chemical

Compression analysis for assessment of pellet plasticity: Identification of reactant pores and comparison between Heckel, Kawakita, and Adams equations

Ann-Sofie Persson et al.

CHEMICAL ENGINEERING RESEARCH & DESIGN (2016)

Add to Collection

Review Chemistry, Applied

Gasification of Woody Biomass

Jianjun Dai et al.

ANNUAL REVIEW OF CHEMICAL AND BIOMOLECULAR ENGINEERING, VOL 6 (2015)

Add to Collection

Article Energy & Fuels

Gravity discharge characteristics of biomass-coal blends in a hopper

Zhiguo Guo et al.

FUEL (2014)

Add to Collection

Article Energy & Fuels

Research on the flow properties of the blended particles of rice straw and coal

Qiang Guo et al.

FUEL (2012)

Add to Collection

Review Thermodynamics

Biomass feeding for thermochemical reactors

Jianjun Dai et al.

PROGRESS IN ENERGY AND COMBUSTION SCIENCE (2012)

Add to Collection

Review Energy & Fuels

Pressure-drop predictions in a fixed-bed coal gasifier

Adam Luckos et al.

FUEL (2011)

Add to Collection

Article Engineering, Chemical

Measuring shear properties and normal stresses generated within a rotational shear cell for consolidated and non-consolidated powders

R. E. Freeman et al.

POWDER TECHNOLOGY (2009)

Add to Collection

Article Engineering, Chemical

On the physical interpretation of the Kawakita and Adams parameters derived from confined compression of granular solids

Josefina Nordstrom et al.

POWDER TECHNOLOGY (2008)

Add to Collection

Review Engineering, Chemical

Product design of cohesive powders - Mechanical properties, compression and flow behavior

J Tomas

CHEMICAL ENGINEERING & TECHNOLOGY (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.