☆ 4.6 Article

Polishing process of 4H-SiC under different pressures in a water environment

DIAMOND AND RELATED MATERIALS (2023)

Related references

Note: Only part of the references are listed.

Article Engineering, Manufacturing

Phase transition and plastic deformation mechanisms induced by self-rotating grinding of GaN single crystals

Chen Li et al.

Summary: The study explores the deformation and removal mechanisms of gallium nitride (GaN) single crystals during ultra-precision machining. The experimental results show that abrasive size significantly affects the surface morphology and roughness, leading to a transition from brittle fracture-dominated surface to a plastic surface with reduced abrasive size. Through cross-sectional TEM method and MD simulation, it is found that plastic deformation in GaN crystals is caused by the formation of polycrystalline nanocrystals and defects, with an observable delamination phenomenon in the plastic deformation zone.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2022)

Add to Collection

Article Chemistry, Physical

Anisotropy dependence of material removal and deformation mechanisms during nanoscratch of gallium nitride single crystals on (0001) plane

Chen Li et al.

Summary: Nanoscratch tests on GaN single crystals revealed that crack-free plastic deformation could be achieved along different zone axes, with deeper penetration depth and less phase transformation along the [11-20] zone axis. Higher stress along the [1-100] zone axis induced more phase transition from hexagonal system to cubic system. This study enhances understanding of the anisotropy dependence of material removal and damage mechanisms in GaN crystals.

APPLIED SURFACE SCIENCE (2022)

Add to Collection

Article Chemistry, Physical

A novel approach to obtain near damage-free surface/subsurface in machining of single crystal 4H-SiC substrate using pure metal mediated friction

Min Wu et al.

Summary: The high-speed friction-induced removal behavior of single crystal silicon carbide (4H-SiC) by pure metals (iron and nickel) was investigated in this study. The subsurface damage of SiC substrates on both C-face and Si-face was explored. It was found that the C-face SiC substrate had almost no damage, while crystal defects were evidenced on the Si-face SiC substrate. The material removal rate was highest on the Si-face using pure nickel. The formation of silicide and/or oxide indicated that the material removal of both the C-face and Si-face of 4H-SiC was dominated by the friction-induced chemical interaction. A friction reaction-removal model of single crystal 4H-SiC substrate using pure metal was proposed.

APPLIED SURFACE SCIENCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of polishing pressure and sliding speed on the material removal mechanism of single crystal diamond in plasma-assisted polishing

Nian Liu et al.

Summary: This study systematically investigates the effects of polishing pressure and sliding speed in plasma-assisted polishing (PAP) on single crystal diamond (SCD) substrates. The results show that low polishing pressures lead to a smooth atomic-scale surface, while high pressures result in a rough surface with grooves. Furthermore, the sliding speed has minimal effect on the surface quality parameter.

DIAMOND AND RELATED MATERIALS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

A perspective on leakage current induced by threading dislocations in 4H-SiC Schottky barrier diodes

Jhong-Ren Huang et al.

Summary: This study compared the influences of threading edge and screw dislocation (TED and TSD) defects on the leakage current of 4H-SiC Schottky barrier diodes (SBDs). Experimental results showed that TEDs had a stronger correlation with leakage current under soft breakdown compared to TSDs. Additionally, Kelvin probe force microscopy indicated that the work function at TED sites was lower than at TSD sites by about 15 meV.

MATERIALS LETTERS (2022)

Add to Collection

Article Engineering, Electrical & Electronic

The effect of contact types on SiC polishing process

Yuqi Zhou et al.

Summary: Through molecular dynamics simulation, the study reveals that the self-rotation of diamond abrasives during polishing significantly impacts the polishing characteristics of SiC wafers, reducing structural damage and frictional forces.

MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING (2022)

Add to Collection

Article Engineering, Mechanical

Effect of water film on the nano-scratching process of 4H-SiC under the constant load

Yuqi Zhou et al.

Summary: The effects of water film and scratching load on tribological properties were investigated using molecular dynamics simulation. The results showed that water film reduces the friction coefficient and enhances heat dissipation during scratching. The presence of water film inhibits the formation of dislocations by affecting the formation of Si-Si bonds. Scratching in a water-wetted environment improves surface quality and reduces sub-surface damage, but negatively affects material removal rate. The effect of increasing load is opposite to that of adding water.

TRIBOLOGY INTERNATIONAL (2022)

Add to Collection

Article Materials Science, Ceramics

Atomistic investigation of machinability of monocrystalline 3C-SiC in elliptical vibration-assisted diamond cutting

Liang Zhao et al.

Summary: The study reveals the mechanisms governing machined surface formation of hard brittle monocrystalline 3C-SiC in ultrasonic elliptical vibration-assisted diamond cutting through molecular dynamics simulations. Different deformation modes and their correlations with surface integrity are shown.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Chemistry, Physical

Influence mechanism of defects on the subsurface damage and structural evolution of diamond in CMP process

Song Yuan et al.

Summary: It has been found that initial defects on material surfaces can lead to more amorphous damage layers and affect structural evolution, having a significant impact on subsequent machining quality and subsurface damage.

APPLIED SURFACE SCIENCE (2021)

Add to Collection

Article Engineering, Mechanical

Modification mechanism of collaborative ions implanted into 4H-SiC by atomic simulation and experiment

Qiang Kang et al.

Summary: Ion implantation is increasingly used to assist machining micro/nano devices, with a method of heavy ions assisted light ions implantation proposed for modifying 4H-SiC surface. Through MD simulation and experiments, it was shown that collaborative ion implantation effectively modifies the surface of hard and brittle materials, bringing benefits for subsequent ultra-precision machining.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Review Engineering, Manufacturing

Science and art of ductile grinding of brittle solids

Han Huang et al.

Summary: This article reviews the current state of the art of ductile grinding and outlines the underlying science behind pertinent machining events, emphasizing the importance of wheel requirements and variables in the grinding process. The critical influence of material microstructures on local deformation mechanisms and material removal is highlighted as well.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2021)

Add to Collection

Article Engineering, Mechanical

Effects of pressure and velocity on the interface friction behavior of diamond utilizing ReaxFF simulations

Song Yuan et al.

Summary: The study found that pressure and sliding velocity impact the interface friction behavior during the chemical mechanical polishing process of diamond, affecting the friction force and atom removal in different stages. This elucidates the technological parameters for ultra-precision and low-damage machining of diamond.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Article Automation & Control Systems

Experimental studies on material removal mechanisms in ultrasonic assisted grinding of SiC ceramics with a defined grain distribution brazed grinding wheel

Kai Ding et al.

Summary: The study compared the material removal mechanism in Ultrasonic Assisted Grinding (UAG) and Conventional Grinding (CG) for SiC, finding a transition from ductile removal to brittle fracture with increasing undeformed chip thickness. Additionally, UAG showed lower surface/subsurface breakage, surface roughness, grinding force, and specific grinding energy compared to CG under identical operating conditions.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)

Add to Collection

Article Physics, Condensed Matter

Effect of inclusion on 4H-SiC during nano-scratching from an atomistic perspective

Yuhua Huang et al.

Summary: In this study, the impact of inclusions on scratching behavior during SiC epitaxy was explored through molecular dynamics modeling. It was found that inclusions significantly affect the microstructure, atomistic behavior, and machinability. Eliminating inclusions requires a high penetration depth, but increases the sensitivity of process parameters.

JOURNAL OF PHYSICS-CONDENSED MATTER (2021)

Add to Collection

Article Engineering, Manufacturing

Removal behavior of micropipe in 4H-SiC during micromachining

Yuhua Huang et al.

Summary: Silicon carbide is a good semiconductor material due to its performance in high-voltage and high-frequency fields, but defects like micropipe can impact device performance. Research shows that adjusting penetration depth during micromachining may not completely eliminate the effect of micropipe, but different dynamic behaviors of 4H-SiC under various penetration depths could be a strategy for detecting or controlling the impact of micropipe.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Chemistry, Physical

Effects of pressure and slurry on removal mechanism during the chemical mechanical polishing of quartz glass using ReaxFF MD

Xiaoguang Guo et al.

APPLIED SURFACE SCIENCE (2020)

Add to Collection

Article Materials Science, Ceramics

Molecular dynamics study of the removal mechanism of SiC in a fixed abrasive polishing in water lubrication

Piao Zhou et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Engineering, Mechanical

Insight into the mechanism of low friction and wear during the chemical mechanical polishing process of diamond: A reactive molecular dynamics simulation

Song Yuan et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Review Physics, Applied

Defect engineering in SiC technology for high-voltage power devices

Tsunenobu Kimoto et al.

APPLIED PHYSICS EXPRESS (2020)

Add to Collection

Article Physics, Condensed Matter

Dependency of the structure of a water layer sandwiched by silicon carbide on shear speed and temperature

Bin Lin et al.

JOURNAL OF PHYSICS-CONDENSED MATTER (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Atomistic mechanisms of chemical mechanical polishing of diamond (100) in aqueous H2O2/pure H2O: Molecular dynamics simulations using reactive force field (ReaxFF)

Xiaoguang Guo et al.

COMPUTATIONAL MATERIALS SCIENCE (2019)

Add to Collection

Article Engineering, Mechanical

Insights on low-friction mechanism of amorphous carbon films from reactive molecular dynamics study

Xiaowei Li et al.

TRIBOLOGY INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Molecular dynamics simulation of SiC removal mechanism in a fixed abrasive polishing process

Piao Zhou et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Study on nanomechanical properties of 4H-SiC and 6H-SiC by molecular dynamics simulations

Zige Tian et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Engineering, Mechanical

A study of ultraprecision mechanical polishing of single-crystal silicon with laser nano-structured diamond abrasive by molecular dynamics simulation

Houfu Dai et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Insights into the atomistic behavior in diamond chemical mechanical polishing with •OH environment using ReaxFF molecular dynamics simulation

Zhuoying Shi et al.

COMPUTATIONAL MATERIALS SCIENCE (2019)

Add to Collection

Review Engineering, Electrical & Electronic

Review on SiC MOSFETs High-Voltage Device Reliability Focusing on Threshold Voltage Instability

K. Puschkarsky et al.

IEEE TRANSACTIONS ON ELECTRON DEVICES (2019)

Add to Collection

Article Materials Science, Ceramics

A study of deformation behavior and phase transformation in 4H-SiC during nanoindentation process via molecular dynamics simulation

Bo Zhu et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Sub-nanoscale polishing of single crystal diamond(100) and the chemical behavior of nanoparticles during the polishing process

Song Yuan et al.

DIAMOND AND RELATED MATERIALS (2019)

Add to Collection

Article Chemistry, Physical

Subsurface damages beneath fracture pits of reaction-bonded silicon carbide after ultra-precision grinding

Zhipeng Li et al.

APPLIED SURFACE SCIENCE (2018)

Add to Collection

Article Chemistry, Multidisciplinary

Investigation of Nanocutting Characteristics of Off-Axis 4H-SiC Substrate by Molecular Dynamics

Miaocao Wang et al.

APPLIED SCIENCES-BASEL (2018)

Add to Collection

Article Chemistry, Physical

A numerical study of ultraprecision machining of monocrystalline silicon with laser nano-structured diamond tools by atomistic simulation

Houfu Dai et al.

APPLIED SURFACE SCIENCE (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Molecular dynamics simulation study of deformation mechanisms in 3C-SiC during nanometric cutting at elevated temperatures

Saeed Zare Chavoshi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Wear process of single crystal diamond affected by sliding velocity and contact pressure in mechanical polishing

Ning Yang et al.

DIAMOND AND RELATED MATERIALS (2015)

Add to Collection

Review Physics, Applied

The current understanding on the diamond machining of silicon carbide

Saurav Goel

JOURNAL OF PHYSICS D-APPLIED PHYSICS (2014)

Add to Collection

Article Engineering, Industrial

Damage-free machining of monocrystalline silicon carbide

Hiroaki Tanaka et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Chemistry, Physical

Friction in a Thin Water Layer: Dissociative versus Nondissociative Friction

M. Paliy et al.

JOURNAL OF PHYSICAL CHEMISTRY C (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Visualization and analysis of atomistic simulation data with OVITO-the Open Visualization Tool

Alexander Stukowski

MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING (2010)

Add to Collection

Review Materials Science, Multidisciplinary

Prospects for SiC electronics and sensors

Nick G. Wright et al.

MATERIALS TODAY (2008)

Add to Collection

Article Materials Science, Multidisciplinary

Analytical potential for atomistic simulations of silicon, carbon, and silicon carbide

P Erhart et al.

PHYSICAL REVIEW B (2005)

Add to Collection

Article Engineering, Electrical & Electronic

Effects of process parameter variations on the removal rate in chemical mechanical polishing of 4H-SiC

CL Nelson et al.

JOURNAL OF ELECTRONIC MATERIALS (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.